EUROM VK2001 Fan Heater Instruction Manual

: June 5, 2024
: EUROM

Table of Contents

Technical data
Warning electric heaters
Description
Location and connection
Set-up and operation
Safety features
Cleaning and maintenance
Documents / Resources

Instruction manual
VK2001 Fan Heater
Art. nr. 350234

This product is only suitable for well-insulated spaces or occasional use.

Information required for the electric local space heaters
Model identifier(s): VK2001

Item	Symbol	Value	Unit	Item	Unit
Heat output		Type of heat input, for electric storage local space heaters

Thank you
Thank you very much for choosing a EUROM device. You have made a good choice! We hope you will be satisfied with its functioning.
To get maximum profit from your product, it is important to read this manual attentively and totally before use and to understand what is written. Read especially the safety instructions: they are there to protect you and your environment.
Keep the manual in a safe place for future reference. The store also the package: that is the best protection for your product in times of no-use. And if you at any time pass the appliance on, pass on the manual and package too.
We wish you a lot of fun with the VK2001!
Eurom
Kokosstraat 20
8281 JC Genemuiden (NL)
info@eurom.nl
www.eurom.nl

This manual has complied with the utmost care. Nevertheless, we reserve the right to optimize this manual at any time and to adjust it technically. The image used may differ.

Symbol Explanation

Do not cover the device

Technical data

Supply voltage	220-240V~50Hz
Maximum capacity	2000 W
Settings	0-1000-2000 W
Thermostat	+
Dimensions	25 x 12 x 24 cm
Weight	1,13 kg

Warning electric heaters

Safety warning – general

Read the user instructions carefully and completely before using (and installing) this device. Keep the instruction leaflet somewhere safe so that you can consult it and pass it on in the future.
Before use, check your new device (including cable and plug) for any visible damage.
Never use a damaged device but take it back to the supplier for a replacement.
In the event of incorrect usage or installation, there is a risk of electric shocks and/or a fire hazard.

Device position warnings

This device is not suitable for wall or ceiling installation.
Do not use this device in the immediate vicinity of a bath, shower, or swimming pool.
This device is not suitable for use in damp spaces such as bathrooms, washrooms, etc.
Never locate the device near water points and reservoirs (tap, bath, shower, toilet, sink, swimming pool, etc.). Make sure that the device cannot fall into the water and that
it cannot be penetrated by water. If the device falls into the water make sure you remove the plug from the socket! Do not use a device that is wet inside but take it to be
repaired. Never immerse the device, cable, or plug in water or any other fluid, and never touch the device with wet hands.
The air around the device must be able to circulate freely. Never install it too close to walls or large objects and never under a shelf, cupboard, curtains, or similar. When
locating the device, make sure you have the following minimum free space:
Front, minimum free space 100 cm
Back, minimum free space 30-50 cm
Sides, minimum free space 100 cm
Top, minimum free space 100 cm
Always place the unit on a sturdy, flat horizontal surface
The base on which the device is placed must not be made of flammable materials. It must be resistant to temperatures of at least 125°C without burning, melting,
deforming, or bursting into flames. Check regularly to ensure that the surface is not overheating; this could be dangerous!
Never place the device on surfaces such as beds or deep-pile carpets as openings could be blocked.
Do not place the device near an open window as rain could blow in; do not place it on wet surfaces and avoid any liquids being spilled nearby. Do not place the device behind a door or along a walking route to avoid accidental trips.
Do not place the device near, under, or facing an electrical socket and not in the vicinity of an open fire or heat source.
Do not use the device nearby or facing furniture, curtains, paper, clothing, bedding, or other flammable materials. Keep at least 1 meter from the device!
Do not use the heater outdoors or in areas that are smaller than 15m³.
The device contains hot and/or glowing and sparking components. Do not, therefore, use where fuels, paint, flammable fluids, and/or gases are stored. Do not use the
device in an environment that poses a fire risk, e.g. near gas tanks, gas pipes, or aerosols. This is an explosion and fire risk!

Warnings – use

Do not use additions/accessories on the device that have not been supplied or approved by the manufacturer.
Only use the device for its intended purpose and in the manner set out in this instruction leaflet.
Some parts of this device will get very hot and could cause burns. You must pay particular attention to children, vulnerable persons and pets that are present near the device. Never leave them alone with a working device.
Never cover or block the device; it will overheat and this could lead to a fire risk.
Never hang or place objects such as clothing, blankets, cushions, paper, etc. on the device. The minimum distance of 1 meter between the device and flammable materials must always be applied. Ventilation openings should never be blocked as this may pose a fire risk. Never use the device to dry clothing or place anything on it. Do not let anything lean against the device!
Do not set the device to come on automatically using a timer, clock, or another facility.
You must always check for safe conditions before using the fireplace! Never use the device with an external voltage regulator such as a dimmer or similar, as this could be
dangerous!
The device is exclusively intended for normal, household usage. Only use for providing heat in your home.
Connection voltage and frequency, as given on the device, must correspond to that of the socket to be used and the electrical installaJ
Only connect the device to a fixed socket. Do not use multi-plug adapters or similar.
During use, the plug may begin to feel warm; this is normal. If it’s really warm, there may be something wrong with the socket. Please contact your electrician.
Always turn off the device and remove the plug from the power socket: Never turn the device off using the plug!
Prevent foreign objects from entering the radiation/ventilation or outlet openings on the device. This may cause electric shock, fire, or damage.
Never leave a working device unattended but switch it off and then remove the plug from the socket.
Always remove the plug from the socket when the unit is not in use! Always remove the plug by pulling on the plug itself; never pull on the electrical cable!
This device gets hot during use. Never touch the device when it is on or shortly thereafter; it could burn you.
Never operate the device with wet hands.

Warnings by whom the device may be used

Children younger than 3 must be kept out of the vicinity of the device unless they are continuously supervised.
Children between the ages of 3 and 8 may only switch the device on or off if it is set up or installed at its usual location and they are supervised or have received
instructions regarding the safe use of the device and understand the corresponding hazards. Children between the ages of 3 and 8 may not insert the plug into the socket, adjust the device settings, or clean or maintain it.
This device can only be used by children from the age of 8 and elderly persons and persons with diminished physical or mental capacities or a lack of experience and expertise if they are supervised or have received instructions regarding the safe use of the device and understand the corresponding hazards.
Children may not clean or maintain the device without supervision.
Children may not play with the device.

Warnings for maintenance

Keep the device clean. Dust, dirt, and/or deposits in the device often lead to overheating. Ensure that this type of build-up is regularly removed.
Always switch the device off, remove the plug from the socket and let the device cool down before you:
– clean the device
– users maintain the device.
– touch or move the device.
Never switch the device on if you have noticed damage to the device itself, the cable or plug, or if it does not work properly, makes strange noises, smells odd or you can see smoke, or if it has fallen or shows any other signs of damage. Remove the plug from the socket immediately. Take the entire device back to your supplier or recognized electrician to be checked and/or repaired. Always ask for original parts to be used.
The device may only be opened and/or repaired by a competent and qualified person. Do not carry out your own repairs as this could be dangerous! Repairs carried
out by unauthorized persons or changes made to the device could damage the dust/waterproof capacity of the device and will nullify the guarantee and the manufacturer’s liability.
If the electrical cable is damaged, it must be replaced by the manufacturer, their service department, or somebody with similar qualifications in order to prevent creating a hazard.

Failing to adhere to points 3, 4, and 5, could lead to damage, fire, and/or personal injury. They will invalidate the guarantee and the supplier, importer, and/or manufacturer shall not be liable for the consequences

Description

1. control dial
2. thermostat dial
3. pilot light| 4. handle
5. air outlet grill
6. air intake grill
---|---

Location and connection

Remove all packaging material and keep it out of reach of children. After removing the packaging, check the appliance for damage or other signs that could indicate a fault/defect/malfunction. In case of doubt, do not use the appliance, but contact your vendor for inspection or replacement.
Select a suitable location for the device taking into account all the aforementioned warnings in this manual.
This radiator cannot be hung but must stand: upright (on the feet) or flat (on the handle and feet).
Make sure a functioning heater is always placed on a solid, flat, and horizontal surface.
Check if the control dial is set to ‘OFF’ (O).
Fully extend the power cord and plug it into a suitable 220/240V socket. To prevent circuit overloading, check that no other appliances are connected to the same group.

Set-up and operation

Turn the thermostat dial to maximum (clockwise as far as possible).
Switch the heater on by turning the control dial to one of the following three positions:
Fan only (thermostat always to maximum)
● Heating at half power (1000W)
●● Heating at full power (2000W)
The light at the front will turn on.
It is most economical to heat the space at full power, then to switch to half- power to maintain the temperature.
Both at half and full power, the fan rotates at the same speed; the difference between the two lies in the number of heating elements in use.
Once the desired temperature is reached, turn the thermostat dial back slowly until you hear a click. The temperature is now set. The heater will automatically switch on and off to maintain the set temperature. When the heater switches off, the pilot light turns off as well. To set a higher or lower temperature, turn the thermostat dial either
clockwise or anticlockwise.
To switch the heater off, set the power dial to ‘0’ (off). The pilot light will turn off. The pilot light, in other words, indicates that the heater is switched on, not that the heater is connected to the mains!
Unplug.

Safety features

In case of internal overheating, the overheating safeguard will switch the heater off. This may occur if the heater cannot give off enough heat or if it cannot draw in enough fresh
air. As mentioned above, this is generally caused by (partially) covering the heater, obstructing the air intake and/or outlet grills, or installing the heater too close to a wall or something similar. When the overheating safeguard switches the heater off, set the mode selector dial to ‘0’ (off), unplug, and allow the heater to cool down. Remove and/or amend the cause of overheating and reuse the heater as normal. If you cannot find a cause and overheating recurs, stop using the heater, and take it in for inspection/repair.

Cleaning and maintenance

Keep the heater clean. Deposits of dust and dirt in the appliance are a common cause of overheating so these should be removed regularly. Switch off the heater, remove the plug from the socket and allow the heater to cool down before cleaning or carrying out maintenance work.

Wipe the outside of the heater regularly with a dry or slightly damp cloth. Do not use aggressive soaps, sprays, cleaners or abrasives, waxes, polishes, or chemical solutions! Using a vacuum cleaner, carefully remove any dust and dirt from the grills and ensure that the air intake and outlet openings are clean. Be careful not to touch or damage any internal parts during cleaning!
The heater contains no other parts which need maintenance.
At the end of the season, store the cleaned heater in the original packaging if possible.
Store upright in a cool, dry, and dust-free place.

Disposal

At its end of life, discard the device according to the local laws and regulations, or deliver the device to your supplier.

EUROM
Kokosstraat 20
8281 JC Genemuiden
The Netherlands
info@eurom.nl
www.eurom.nl
070322