Nedis BTTC200BK Bluetooth Transmitter Receiver User Manual
- June 5, 2024
- nedis
Table of Contents
BTTC200BK Bluetooth Transmitter Receiver
User Manual
Preface
Thank you for purchasing the Nedis BTTC200BK.
This document is the user manual and contains all the information for correct, efficient and safe use of the product.
This user manual is addressed to the end user. Read this information carefully before installing or using the product.
Always store this information with the product for use in the future.
Product description
Intended use
The BTTC200BK is a device that allows you to transmit or receive Bluetooth audio.
The BTTC200BK functions wirelessly with a built-in, rechargeable battery.
The product is not intended for professional use.
Any modification of the product may have consequences for safety, warranty and proper functioning.
Specifications
Product
|
Bluetooth Transmitter Receiver
---|---
Article number
|
BTTC200BK
Power supply
|
5 VDC / 1 A
Battery
|
Lithium-Polymer
Battery capacity
|
450 mAh
Maximum play time
|
Up to 22 hours
Max. battery charging time
|
Up to 2 hours
Maximum Standby Time
|
Up to 48 hours
Bluetooth® version
|
5.0
Maximum transmission power
|
1.31 dBm
Bluetooth frequency range
|
2402 – 2480 MHz
Bluetooth signal range
|
Up to 10 meters
Bluetooth profiles
|
A2DP
Supported codecs
|
SBC / aptXTM, aptXTM Low Latency
Connections
|
AUX input/output
SPDIF input
SPDIF output
Micro USB
Main parts (image A)
A
1. AUX / SPDIF switch
2. Volume down / previous track button
3. On/off / play / pause button
4. Volume up / next track button
5.button
6. Status indicator LED
7. Mode switch
8. AUX port
9. SPDIF input (Tx)
10. SPDIF output (Rx)
11. Micro USB charging port
12. Stereo audio cable 2x RCA male to 3.5 mm female
13. 3.5 mm to 3.5 mm audio cable male to male
14. USB charging cable
15. SPDIF Optical Audio Cable male to male
Safety instructions
WARNING
- Ensure you have fully read and understood the instructions in this document before you install or use the product. Keep this document for future reference.
- Only use the product as described in this document.
- Do not use the product if a part is damaged or defective. Replace a damaged or defective product immediately.
- Do not drop the product and avoid bumping.
- This product may only be serviced by a qualified technician for maintenance to reduce the risk of electric shock.
- Disconnect the product from the power source and other equipment if problems occur.
- Do not expose the product to water or moisture.
- Do not dismantle, open or shred secondary cells or batteries.
- Do not expose cells or batteries to heat or fire. Avoid storage in direct sunlight.
- Retain the original product literature for future reference.
- Do not leave a battery on prolonged charge when not in use.
- After extended periods of storage, it may be necessary to charge and discharge the cells or batteries several times to obtain maximum performance.
- Batteries contain explosive gases. Prevent contact with flames and sparks. Provide adequate ventilation during charging.
- Some wireless devices may interfere with implantable medical devices and other medical equipment, such as pacemakers, cochlear implants and hearing aids. Consult the manufacturer of your medical equipment for more information.
- Do not use the product at locations where the use of wireless devices is prohibited due to potential interference with other electronic devices, which may cause safety hazards.
Safety symbols on the product
Icon
|
Description
---|---
|
Electronic equipment needs to bear the CE mark in order to be marketed in the EU. CE marking shows that a product is assessed before being placed on the market and that it meets EU safety, health and environmental protection requirements. CE marking is also sometimes accepted as a means of compliance with type-approval requirements; for example, electronic components that require type-approval and also CE marking for electromagnetic compatibility (EMC) or low-voltage equipment.
|
Indication to explain that the product needs to be collected separately when disposed. Do not throw in the trash bin.
Installation
- Check the contents of the package
- Check that all parts are present and that no damage is visible on the parts. If parts are missing or damaged, contact the Nedis B.V. service desk via the website: www.nedis.com.
Charging the product
1. Connect A14 to A11.
2. Plug the other end of A14 into a 5V/1A USB adapter (not provided).
3. Plug the USB adapter into a power outlet.
- A 6 Burns red to indicate that the product is charging.
- A 6 switches off when the battery is fully charged.
- When the battery is low, there is a prompt sound and A 6 blinks red.
Switching the product on/off
1. Press and hold A 3 for 3 seconds to switch the product on or off.
- The product automatically switches off when it is not paired within 10 minutes.
Use
Receiver mode (image B)
B
Option 1: Using an AUX connection
1. Set the AUX / SPDIF switch A 1 to AUX.
2. Set the mode switch A 7 to RX.
3. Plug the 3.5 mm to 3.5 mm audio cable A13 into the AUX A 8.
4. Plug the other end of A13 into the audio output device.
- You can also connect an audio device with the stereo audio cable 2x RCA male to 3.5 mm female A12.
Option 2: Using an SPDIF connection.
1. Set the AUX / SPDIF switch A 1 to SPDIF.
2. Set the mode switch A 7 to RX.
3. Plug the SPDIF optical cable A15 into the SPDIF output (Rx) A10.
4. Plug the other end of A15 into the audio output device.
5. Switch on the product.
- Press and hold A 4 to turn the volume up.
- Press and hold A 2 to turn the volume down.
- A 6 Blinks blue.
6. Enable Bluetooth on the device you want to pair.
7. Press Bluetooth button A 5 to start pairing.
8. Select “BTTC200BK” from the list of available Bluetooth devices on your device.
- If asked, enter the pairing code ‘0000’.
- A 6 blinks slowly to indicate pairing is successful.
Transmitter mode (image C)
C
Option 1:
1. Set the AUX / SPDIF switch A 1 to AUX.
2. Set A 7 to TX.
3. Plug A13 into A 8.
4. Plug the other end of A13 into your audio source.
- You can also connect an audio device with the stereo audio cable 2x RCA male to 3.5 mm female A12.
Option 2:
1. Set the AUX / SPDIF switch A 1 to SPDIF.
2. Set A 7 to TX.
3. Plug A15 into SPDIF input (Tx) A 9.
4. Plug the other end of A15 into your audio source.
5. Switch on the product.
- A 6 Blinks green.
6. Keep your Bluetooth audio device within range and switched on.
- Pairing time will vary depending on the device used.
- A 6 Burns to indicate pairing is successful.
Connect a second device
After successfully connecting the first device, press A 5 again to pair to a second device.
- The devices must be one meter apart from each other.
- The two devices are connected simultaneously.
- If the pairing does not work, switch the product off and on.
Disconnect paired devices
- Press and hold A 5 for 3 seconds.
- To disconnect a single device, switch off the Bluetooth of that device.
- To clear the pairing list press and hold A 5 for 8 seconds.
- A 6 Blinks twice when cleared.
Recommendations
- When connecting with two devices, use the devices with the same version of Bluetooth.
- In Bluetooth transmit mode, only headphones and similar devices can be connected. Smartphones cannot be paired with this mode.
- Do not use this product in a place with obstructions or other Bluetooth devices to avoid interference.
- When pairing fails, clear the list of paired devices on the product.
Maintenance
- Clean the product regularly with a soft, clean, dry cloth. Avoid abrasives that can damage the surface.
- Do not use aggressive chemical cleaning agents such as ammonia, acid or acetone when cleaning the product.
Warranty
Any changes and/or modifications to the product will void the warranty. We accept no liability for damage caused by improper use of the product.
Disclaimer
Designs and specifications are subject to change without notice. All logos, brands and product names are trademarks or registered trademarks of their respective owners and are hereby recognized as such.
Disposal
|
This symbol indicates that this product should not be thrown away with other household waste throughout the EU. To prevent possible harm to the environment or human health by uncontrolled waste disposal, you are responsible for recycling it so that it can promote the sustainable reuse of raw materials. To return your used product, you can use the regular return and collection systems or contact the store where the product was purchased. They can recycle this product for the environment.
---|---
Declaration of Conformity
We, Nedis B.V. declare as manufacturer that the product BTTC200BK from our brand Nedis®, produced in China, has been tested according to all relevant CE standards and regulations and that all tests have been passed successfully. This includes, but is not limited to the RED 2014/53/EU regulation.
The complete Declaration of Conformity (and the safety datasheet if applicable) can be found and downloaded via:
For additional information regarding the compliance, contact the customer service:
Web: www.nedis.com
E-mail: service@nedis.com
Phone: +31 (0)73-5991055 (during office hours)
Nedis B.V., de Tweeling 28
5215 MC ’s-Hertogenbosch, the Netherlands
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>