Nedis HPBT8000BK Wireless Bluetooth Sports Earphones User Manual
- June 5, 2024
- nedis
Table of Contents
HPBT8000BK Wireless Bluetooth Sports Earphones
User Manual
Preface
Thank you for purchasing the Nedis HPBT8000BK.
This document is the user manual and contains all the information for correct, efficient and safe use of the product.
This user manual is addressed to the end user. Read this information carefully before installing or using the product.
Always store this information with the product for use in the future.
Product description
Intended use
The Nedis HPBT8000BK is a pair of wireless sport earphones.
It can connect to an audio source via Bluetooth.
The fin eartips prevent the earphones from falling out during movement. This makes the earphones perfect for both indoor and outdoor exercising.
Any modification of the product may have consequences for safety, warranty and proper functioning.
Specifications
Product
|
In-ear sport earphones
---|---
Article number
|
HPBT8000BK
Bluetooth® version
|
5.0
Battery Capacity
|
80 mAh
Charging time
|
±2 hours
Playback time
|
Up to 5 hours
Talk time
|
Up to 5 hours
Charging current
|
5 V/DC – 500 mA
Bluetooth frequency range
|
2.402 – 2.480 GHz
Wireless Transmission effective distance
|
Up to 10 meters
Maximum Transmission power
|
4 dBm
Maximum Antenna gain
|
1.7 dBi
Speaker driver size
|
12 mm dynamic
Microphone
|
Built-in
Cable length
|
60 cm
Parts list
1. Fin eartips
2. Earphones
3. Volume+ button
4. Multifunction button
5. Status indicator LED
6. Micro USB port with protective cap
7. Volume- button
Safety instructions
WARNING
- Only use the product as described in this manual.
- Do not expose the product to water or moisture.
Installation
- Check the contents of the package
- Check that all parts from the parts list are present and that no damage is visible on the parts. If parts are missing or damaged, contact the Nedis B.V. service desk via the website: www.nedis.com.
Use
Switching on the earphones
- Press and hold 4 for 4 seconds to switch on the earphones.
- The status indicator LED 5 on the earphones blinks blue three times .
Charging the earphones
- Plug the micro USB cable into the micro USB slot of the earphones 6.
- The status indicator LED 5 on the earphones burns red to indicate the earphones are charging.
- The status indicator LED 5 on the earphones turns blue when the earphones are fully charged.
Pairing the earphones to a Bluetooth audio source
1. While the earphones are switched off, press and hold 4 to enter pairing mode.
- The status indicator LED 5 on the earphones start to blink blue/red to indicate the earphones are pairing.
2. Enable Bluetooth on the device you want to pair the earphones with.
3. Select “HPBT8000” from the list of available Bluetooth devices on your device.
4. If asked, enter the pairing code ‘0000’.
- When pairing is complete, the status indicator LED 5 will light up blue.
- The earphones will automatically reconnect with the last paired device when switched on.
Controlling the volume
- Raise the volume on the earphones with the Volume+ button 3.
- Lower the volume on the earphones with the Volume- button 7.
Controlling the music
- Press 4 to play or pause the music
- Press and hold 3 to skip to the next song.
- Press and hold 7 to go back to the start of the song. Press and hold again within 2 seconds to go to the previous song.
Making phone calls
- With the earphones connected to a mobile phone via Bluetooth, phone calls will automatically be redirected to the earphones.
- When you receive an incoming phone call, the status indicator LED 5 will flash blue and the phone will ring through the speakers of the earphones.
- To answer an incoming call, press 4.
- To reject an incoming call, press and hold 4 for 2 seconds.
- To end a call, press 4.
- To cancel an outgoing phone call, press 4.
- To quickly redial the last called number, double press 4.
Low battery alarm
- When the battery is low, the status indicator LED 5 will flash red 3 times every 20 seconds
Switching off the earphones
- Press and hold 4 for 4 seconds to switch off the earphones.
- The status indicator LED 5 on the earphones blinks red twice.
- The earphones will automatically switch off when there is no Bluetooth connection for more than 6 minutes.
Maintenance
- Clean the product regularly with a soft, clean, dry cloth. Avoid abrasives that can damage the surface.
- Do not use aggressive chemical cleaning agents such as ammonia, acid or acetone when cleaning the product.
Troubleshooting
Problem
|
Possible cause
|
Solution
---|---|---
Earphones do not switch on.
|
The batteries are drained.
|
Charge the earphones for at least 30 minutes and retry.
Bluetooth source cannot pair with the earphones.
| |
Remove the earphones from the list of paired devices on the bluetooth source and follow the instructions in chapter “Pairing the earphones to a Bluetooth audio source”.
| |
Restart both devices and try again.
| |
Remove any metal objects or electrical devices that can disturb the signal between the source device and the earphones.
No sound is coming from the earphones.
|
The audio source volume is too low/muted.
|
Raise the volume on the audio source.
|
The earphones volume is too low/muted.
|
Raise the volume on the earphones with the Volume+ button 3.
Warranty
Any changes and/or modifications to the product will void the warranty. We accept no liability for damage caused by improper use of the product.
Disclaimer
Designs and specifications are subject to change without notice. All logos, brands and product names are trademarks or registered trademarks of their respective owners and are hereby recognized as such.
Disposal
|
This symbol indicates that this product should not be thrown away with other household waste throughout the EU. To prevent possible harm to the environment or human health by uncontrolled waste disposal, you are responsible for recycling it so that it can promote the sustainable reuse of raw materials. To return your used product, you can use the regular return and collection systems or contact the store where the product was purchased. They can recycle this product for the environment.
---|---
Declaration of Conformity
We, Nedis B.V. declare as manufacturer that the product HPBT8000BK from our brand Nedis®, produced in China, has been tested according to all relevant CE standards and regulations and that all tests have been passed successfully. This includes, but is not limited to the RED 2014/53/EU regulation.
The complete Declaration of Conformity (and the safety datasheet if applicable) can be found and downloaded via webshop.nedis.com/HPBT8000BK#support
For additional information regarding the compliance, contact the customer service:
Web : www.nedis.com
E-mail: service@nedis.com
Phone: +31 (0)73-5991055 (during office hours)
Nedis B.V., de Tweeling 28
5215 MC ’s-Hertogenbosch, the Netherlands