Westinghouse 6121640 Wall lamp sensor light wall interior touch sensitive modular Instruction Manual

June 5, 2024
Westinghouse

Westinghouse logoWestinghouse 6121640 Wall lamp sensor light wall
interior touch sensitive modular

OUTDOOR INSTRUCTIONS MANUAL
61216

WARNING: ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.

Read and follow instructions exactly as shown. If instructions are unclear, do not proceed.
Contact a qualified electrician. Read all instructions before beginning. Proper wiring is essential for the safe operation of this fixture. When cutting or drilling into walls or ceilings,  do not damage electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are damaged, do not install the fixture. Return to place of purchase

ASSEMBLY INSTRUCTIONS FOR OUTDOOR LIGHTING FIXTURE

Congratulations on your Westinghouse purchase. This fixture has been designed to give you many years of beauty and service. For questions and comments, please visit www.westinghouselighting.eu/contact- us and www.westinghouselighting.de/contact-us
NOTE: Carefully unpack fixtures and parts. Make sure all parts are included before discarding any packing materials (see figure 1)

Westinghouse 6121640 Wall lamp sensor light wall interior touch sensitive
modular - fig

MOUNTING AND WIRING INSTRUCTIONS

NOTE: Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this fixture.
CAUTION: For fixtures labeled for outdoor and wet location use, provide a water-tight seal between the fixture and the mounting surface by using silicone or similar caulking.

  1. Turn off power at the circuit box to avoid possible electric shock.

  2. Thread mounting screw (A) into mounting bar (B) and secure the mounting screw (A) with a small hex nut (C) (see fig. 1).

  3. Place mounting bar (B) flush against the wall at the desired mounting location. Using side holes as a guide, mark where pilot holes are to be drilled.
    NOTE: Mounting bar (B) must be level for the fixture to hang straight.

  4. Inset two plastic anchors (D) into the pilot holes (for drywall wall).

  5. Align outside mounting bar holes with plastic anchors (D) (if applicable). Secure mounting bar (B) into place using wood screws (E).

  6. Make an electrical connection by loosening the terminal screws on the terminal block (M) and inserting the live, neutral, and ground terminals.

  7. Tighten terminal screws. Make sure there are no stray wires.

  8. Place back plate (H) over mounting screws (A) (see fig. 1).

  9. Secure into place with washer (G) and cap nuts (I).

  10. Removing screw nuts (F) from fixture cover (L) to remove cage shade (J) and glass shade (K), carefully support the cage shade (J) while removing screw nuts (F) from fixture cover (L), then remove the glass shade (K).

  11. Install lamp (not supplied). (Please do not exceed the maximum capacity recommended on the socket).

  12. Secure the glass shade (K) to fixture cover (L), and secure the cage shade (J) using the screw nuts (F).

  13. Turn the power back on at the circuit box.
    GS-26-FS40-WH22

CLEANING AND CARE

To clean, wipe the fixture with a soft cloth. Clean glass with mild soap. Spray from chemical cleaners can discolor the finish of the fixture. Do not use scouring pads, powders,  steel wool, or abrasive paper to clean this fixture.

Meaning of crossed-out wheeled dustbin:
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
Contact your local government for information regarding the collection systems available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.
When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposal at least free of charge.

Appliance specifications – TECHNICAL CHARACTERISTICS

Rated voltage 220-240V~
Rated frequency 50/60 Hz
Rated wattage E27 1 x Max. 60W
Protection class CLASS I
IP number IP44

Westinghouse logoDistributed by:
Westinghouse Lighting, Krefelder Strasse 562
D-41066 Mönchengladbach / Germany
and Westinghouse are trademarks of
Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting
All Rights Reserved.
Made in China
www.westinghouselighting.eu
www.westinghouselighting.de

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Westinghouse User Manuals

Related Manuals