EUROM 363234 Valencia Electronic Fireplace Instruction Manual

[

](https://manuals.plus/wp-content/uploads/2022/07/EUROM- logo-8.png)EUROM 363234 Valencia Electronic Fireplace

Thank you

• Thank you very much for choosing for a EUROM device. You have made a good choice! We hope you will be satisfied about its functioning. To get maximum profit from your product, it is important to read this manual attentive and totally before use, and to understand what is written. Read especially the safety instructions: they are there to protect you and your environment. Keep the manual in a safe place for future reference. Store also the package: that is the best protection for your product in times of no-use. And if you at any time pass the appliance on, pass on the manual and package too.
  We wish you a lot of fun with the Valencia!

• Eurom

• Kokosstraat 20  8281 JC Genemuiden (NL)

• info@eurom.nl

• www.eurom.nl

• This manual has been complied with the utmost care. Nevertheless, we reserve the right to optimize this manual at any time and to adjust it technically. The image used may differ.

Symbol Explanation

 Do not cover the device

Technical data

Warning electric heaters Safety warning – general

1. Read the user instructions carefully and completely before using (and installing) this device. Keep the instruction leaflet somewhere safe so that you can consult it and pass it on in future.
2. Before use, check your new device (including cable and plug) for any visible damage. Never use a damaged device but take it back to the supplier for a replacement.
3. In the event of incorrect usage or installation, there is a risk of electric shocks and/or a fire hazard.

Warnings device position

1. Do not use the device before it has been fully installed as set out in the user instructions. Never use the device standing up or leaning against something, or similar. Never insert the plug into the socket before the device has been correctly installed at the appropriate place.
2. When installing, the following minimum distances should be considered:
3. Minimum distance to ceiling: 100 cm
4. Minimum distance to side walls: 20 cm
5. Minimum distance to the ground: 30 cm
6. The air around the device must be able to circulate freely. Never install it too close to large objects and never under a shelf, cupboard, curtains or similar. The minimum distances from large objects such as shelves, cupboards, etc. to the top, sides and underneath of the device are equal to the aforementioned minimum distances to ceilings, side walls and the ground, respectively.
7. This device is not suitable for installation in damp spaces such as bathrooms, wash rooms etc. Never install the device near water points and reservoirs (tap, bath, shower, toilet, sink, swimming pool, etc.). Make sure that the device cannot fall into water and that it cannot be penetrated by water. If the device falls into water make sure you remove the plug from the socket! Do not use a device that is wet inside but take it to be repaired. Never immerse the device, cable or plug in water or any other fluid and never touch device with wet hands.
8. The wall to which the device is secured and the ceiling and walls within 1 metre of the device must not be made of flammable materials. Materials must be resistant to temperatures of at least 200°C without burning, melting, deforming or bursting into flames. Check regularly to ensure that the wall and ceiling are not overheating; this could be dangerous!
9. Only use the device if it has been secured properly. Make sure that you always use attachment materials that are suitable for the surface you are working with; consult an expert if required.
10. With wall installation: never block the space between the device and the wall.
11. Never install this device behind a door or by an open window, where rain could get in.
12. If this device is connected directly to your electrical installation, it must be installed by a specialist, taking into account the valid regulations/legislation.
13. Do not place the device near, under or facing an electrical socket and not in the vicinity of an open fire or heat source.
14. Do not use the device nearby or facing furniture, curtains, paper, clothing, bedding, towels or other flammable materials. Keep at least 1 metre from device!
15. Do not use the heater outdoors or in areas that are smaller than 15m³.
16. The device contains hot and/or glowing and sparking components. Do not, therefore, use where fuels, paint, flammable fluids and/or gases are stored. Do not use the device in an environment that poses a fire risk, e.g. near gas tanks, gas pipes or aerosols. This is an explosion and fire risk!

Warnings – use

1. Do not use additions/accessories on the device that have not been supplied or approved by the manufacturer.
2. Only use the device for its intended purpose and in the manner set out in this instruction leaflet.
3. Some parts of this device will get very hot and could cause burns. You must pay particular attention to children, vulnerable persons and pets that are present near the device. Never leave them alone with a working device.
4. Never cover or block the device; it will overheat and this could lead to a fire risk. Never hang or place objects such as clothing, towels, blankets, cushions, paper, etc. on the device. The minimum distance of 1 metre between the device and flammable materials must always be applied. Ventilation openings should never be blocked as this may pose a fire risk. Never use the device to dry clothing or place anything on it. Do not let anything lean against the device!
5. The device is exclusively intended for normal, household usage. Only use for providing heat in your home.
6. The connection voltage and frequency, as given on the device, must correspond to that of the socket to be used. The electrical socket to be used must be an earthed connection. The electrical installation must be protected via a 30 mA earth leakage circuit breaker. The electrical socket that you are using must be to hand at all times in order to be able to remove the plug from the socket in the event of an emergency.
7. To avoid overloading and/or fuses being blown, do not use any other equipment on the same socket or electrical group as the one used for the device.
8. Unroll the electric cable for the device fully before inserting the plug into the socket and ensure that the electrical cable does not come into contact with the fireplace or get hot. Do not run the electrical cable under carpet, cover with mats, runners or similar and do not place in areas that are walked on frequently. Ensure that it cannot be stepped on and that no furniture is placed on top of it. Do not bend the electrical cable around sharp corners and do not roll up too tightly after use! Prevent the electrical cable coming into contact with oil, solvents and sharp objects. Check the cable and plug regularly for damage. Do not bend or pinch the electrical cable and do not wind it around the device; this could damage the insulation!
9. The use of an extension cable is not advised as this can lead to overheating and fire. If the use of an extension cable is unavoidable, make sure that it is not damaged and that it is an approved extension cable with a minimum diameter of 3×2,5mm² and a minimum permitted capacity of 2500 Watt. Always fully extend the cable in order to prevent overheating.
10. Only connect the device to a fixed socket. Do not use multi-plug adapters or similar.
11. During use, the plug may begin to feel warm; this is normal. If it’s really warm, there may be something wrong with the socket. Please contact your electrician.
12. Always turn off the device and remove the plug from the power socket: Never turn the device off using the plug!
13. Prevent foreign objects entering the radiation/ventilation or outlet openings on the device. This may cause electric shock, fire or damage.
14. Never leave a working device unattended but switch off and then remove the plug from the socket. Always remove the plug from the socket when the unit is not in use!Always remove plug by pulling on the plug itself; never pull on the electrical cable!
15. Apart from manual use, this device can also be operated via a timer. However you operate it, make sure that the safety guidelines are taken into account at all times!Do not operate the device with an additional time clock, timer, volume control or any other device that automaticaaly turns on the device.
16. This device gets hot during use. Never touch the device when it is on or shortly thereafter; it could burn you.
17.  Never operate the device with wet hands.

Who can use the device?

1. Children younger than 3 must be kept out of the vicinity of the device unless they are continuously supervised.
2. Children between the ages of 3 and 8 may only switch the device on or off if it is set up or installed at its usual location and they are supervised or have received instructions regarding the safe use of the device and understand the corresponding hazards. Children between the ages of 3 and 8 may not insert the plug into the socket, adjust the device settings or clean or maintain it.
3. This device can only be used by children from the age of 8 and elderly persons and persons with diminished physical or mental capacities or a lack of experience and expertise if they are supervised or have received instructions regarding the safe use of the device and understand the corresponding hazards.
4. Children may not clean or maintain the device without supervision.
5. Children may not play with the device.

Warnings for maintenance

1. Keep the device clean. Dust, dirt and/or deposits in the device often lead to overheating. Ensure that this type of build-up is regularly removed.
2. Always switch the device off, remove plug from socket and let the device cool down before you:
   • clean the device
   • users – maintain the device.
   • touch or move the device.
3. Never switch the device on if you have noticed damage to the device itself, the cable or plug or if it does not work properly, makes strange noises, smells odd or you can see smoke, or if it has fallen or shows any other signs of damage. Remove the plug from the socket immediately. Take the entire device back to your supplier or a recognised electrician to be checked and/or repaired. Always ask for original parts to be used.
4. The device may only be opened and/or repaired by a competent and qualified person. Do not carry our your own repairs as this could be dangerous! Repairs carried out by unauthorised persons or changes made to the device could damage the dust/waterproof capacity of the device and will nullify the guarantee and the manufacturer’s liability.
5. If the electrical cable is damaged, it must be replaced by the manufacturer, their service department or somebody with similar qualifications in order to prevent creating a hazard.
   Failing to adhere to points 3, 4, 5, could lead to damage, fire and/or personal injury. They will invalidate the guarantee and the supplier, importer and/or manufacturer shall not be liable for the consequences.

Description

• The VALENCIA comprises an atmospheric fireplace (containing a heating element and ventilator which blows warm air out of the top of the fireplace), wall supports, a remote control and this instruction manual.
• The atmospheric fireplace is covered with a rounded glass plate at the front. There is a metal cabinet behind this which contains the atmospheric elements at the front, air grilles at the sides and, on top, the grille which is used to blow out warm air and the operating panel. The hanging bracket is located at the back and the technical aspects are housed internally.
• The wall supports must be attached to the wall so that the fireplace can be hung on them. Screws, plugs, a spacer bracket and self-tapping screws are supplied.
• With the remote control you can operate all functions of the heater.

Remote control:

• A. ON/OFF button
• B. Button for setting the time
• C. + button
• D. Erasing the time setting
• E. Timer on/off button
• F. Dimmer button
• G. DAY and TIME button
• H. – button
• I. Automatic output selection
• J. 1000W button
• K. 2000W button

Display:

1. Stand-by light
2. Day indicator
3. Temperature and thermostat setting
4. Time indicator and timer setting
5. Lamps of 1000W – 2000W – auto
6. Dimmer setting
7. Operating timer light
8. Timer ON & OFF setting

Location and connection

• Remove all packaging material and keep out of reach of children. After removing packaging, check the appliance for damage or other signs that could indicate a fault/defect/malfunction. In case of doubt, do not use the appliance, but contact your vendor for inspection or replacement.
• Do not use the fireplace before it has been completely installed according to the instructions and you have read the instruction booklet fully!
• This device was designed to be permanently hung on a wall. Ensure the wall is sturdy, completely vertical, is not sensitive to vibration and is not flammable. Make sure it is not made of synthetic material and or covered with flammable material. Be aware of pipes that may be contained within the walls when drilling holes.
• Choose a suitable location for the fireplace, at least one metre from all obstructions, walls and flammable materials (see safety instructions) and in the vicinity of a 16 Amp (at least) fused, earthed electrical socket (protected by a 30 mA earth leakage circuit breaker). This socket must be located to the right of the fireplace.
• There must be at least 30 cm distance between the base of the fireplace and the ground, however, you are advised to place the fireplace at a height of 60 cm. for the best sight. There must be at least 20 cm distance between the fireplace and the side walls, at least 100 cm. between the fireplace and the ceiling. Do not hang the device directly under or in front of an electrical socket (see diagram 1).

• The wall supports must be attached horizontally (use a spirit level!) to the wall. Determine the location of the wall supports (take the above into account), mark the location of the screws and drill 5 holes at the marked places using a 6 mm drill. Put the plugs into the holes and then screw the wall supports to the wall. Be aware of pipes that may be contained within the walls when drilling holes!
• Attach the securing-bracket with both self-tapping screws underneath the fireplace in the holes provided. The flat side of the bracket must be placed against the underside of the fireplace; the other must rest against the wall so that the wall piece sticks out under the fireplace (diagram 3). This bracket will be hidden from sight once the glass screen has been installed.
• Now hang the fireplace carefully on the central wall support with the hanging bracket (see diagram 2). The bracket should not stick out from the support! The electrical cable comes out at the right hand, lower side of the fireplace and must be placed out of range of the heat.
• Now mark the location at which the securing-bracket must be screwed to the wall. Remove the fireplace from the wall, drill both holes and insert a plug. Hang the fireplace on the bracket and screw the securing bracket to the wall.
• Hang the glass plate (two people are needed for this job!) with the four hooks over the four knobs on the sides of the fireplace and check that all four hooks are correctly attached (see diagram 4). Secure the glass plate by tightening the screw that goes through the bracket (which sits on the glass plate).
• Installation is now complete.
  Note : ensure that the weight of the fireplace hangs on the wall supports and not on the little securing bracket!

Operating

• Check that the details on the data plate correspond to those of the electrical supply which you wish to use for the fireplace. Do not use the same connection for any other equipment.
• Install two AAA-1,5V batteries in the remote control.
• Check whether the main switch is set to OFF (O is pushed in)
• Now insert the plug into the grounded socket.
• Push the main switch to ON (I is pushed in). The heater is now on stand-by and the light is switched on at the .
• You can now further operate the fireplace with the remote control or with the buttons on the fireplace itself.

Push-button operation:
If you don’t use the remote control, you can press the relevant buttons on the control panel, manually set it to 3 positions; the corresponding lights will turn on.

• I/O : flame effect only
• I/O + 1000W : flame display and heating at 1000W
• I/O + 2000W : flame display and heating at 2000 Watt (all the lights are turned on). By pressing the I/O button longer, you initiate the dimmer function; the light intensity will increase or decrease with every tweet. Release the button when you have achieved the desired intensity
  Attention! The thermostat cannot be set manually, only with the remote control. The thermostat is standard set to 20°C.

Remote control:

• Press on the ON/OFF button to switch on the heater.

• Now set the desired temperature. The temperature & timer setting will usually show the ambient temperature. By pressing on the + or – button, you see the set temperature flashing for a short time and by pressing the + or – buttons, you can adjust the temperature (from 15 to 30°C). After a few seconds, the display switches back to the ambient temperature and the newly desired temperature is set. The temperature is standard set to 20°C.

• Now you can start operating the heater by pressing the button to 1000W (half output) or 2000W (full output). When the set temperature is above the ambient temperature, the heater will start to heat (1000W, 2000W). The corresponding lights on the display are turned on (1000W-1 star, 2000W-2 stars).
  If you press the IC button, the heater will automatically choose the most suitable output. The corresponding lights on the display are turned on (IC- AUTO).

• The thermostat will switch off the heater as soon as the heater reaches the desired temperature and it will switch it on again if the ambient temperature drops.

• By pressing the ‘dimmer’ button (there are 5 positions), you can intensity or decrease the flame effect of the heater.

• You switch off the heater by pressing the ON/OFF button. The temperature level that you set will remain. However, if you switch on the heater once again, you will have to reset the output.

• If you want to switch off the heater for a longer period, then also set the main switch on O (OFF). The set temperature will now be erased. Finally remove the plug from the socket.

Timer:

• The heater has a built-in weekly timer, which allows you to set a weekly schedule for switching on and off. You must first set the date and time; if you don’t do that, then the heater assumes that it is scheduled for Sunday at 00.00!

  • Press the ON/OFF button to switch on the heater.
  • Press on the DAY/TIME button; the day indicator will light up. Select the arrows Λ and V for the current day and confirm this by pressing the DAY/TIME button again (Sunday, Monday, etc.)
  • The hour indication will now flash. By pressing on the + and – buttons, you select the current hour. Reconfirm by pressing on the DAY/TIME button.
  • The minutes indicator will now flash. By pressing on the + and – buttons, you select the precise time. Confirm by pressing on the DAY/TIME button.
  • Day and time are now set.

• To set the weekly timer, take the following steps:

  • Ensure that the heater is switched on with the ON/OFF button.
  • Press on the TIMER SET button. The indication 01 on the display starts to flash, indicating that you have selected the first timer setting (you can select 10 timer settings). Confirm this by pressing once again on the TIMER SET button.
  • The day indicator will now flash (SUN). Choose the days when the heater must operate (e.g., from Monday to Friday) by pressing + next to the days you have selected and pressing – next to the days that you don’t want to select. Use to arrows to move to the next day. Press again on the TIMER SET button to choose the days and confirm.
  • The hours indication will now flash and you will see ON on the display. By selecting the + and – buttons, you choose the hours when you want the heater to operate. Confirm by pressing the TIMER SET button.
  • The minutes indicator will now flash. By pressing the + and – buttons, you select the time period (in intervals of 10 minutes) for the heater to operate. Confirm by pressing on the DAY/TIME button. The starting time is now set.
  • The hour indicator is flashing again to order for you to set at which time the operation must end. OFF appears on the display. Select the time in the same way you selected the operating time and confirm by using the TIMER SET button.
  • Now the temperature setting starts to flash. Using the + or – buttons, select the desired temperature and confirm by using the TIMER SET button.
  • You initial timer setting is now set.
  • To generate a second setting, press once again on the TIMER SET button. While 01 is flashing, press on the + button: 02 will appear. Confirm this using the TIMER SET button and subsequently set new days, hours and minutes as described above.
  • You can generate maximum 10 time settings. Prevent the setting from containing any conflicting or overlapping orders.

• To operate the heater according to the timer settings, do the following:

  • Switch on the heater using the ON/OFF button.

  • Press the 1000W or 2000W button to set the desired output. If the desired temperature is above the ambient temperature, the heater will begin to heat
    (1000W, 2000W). The corresponding light will light up on the display (1000W-1 star, 2000W-2 stars).
    If you press the IC button (automatic choice of output), the heater possible will start to heat the room 20 minutes before the set time. After 20 minutes the heater will automatically choose the most suitable output.The corresponding light will light up on the display (IC-AUTO).

  • By pressing the ‘dimmer’ button (there are 5 positions), you can intensity or decrease the flame effect of the heater.

  • Now activate the timer by pressing on the TIMER ON/OFF button. The operating-timer light will light up and the timer set 01 will flash. If you press OK now, then the heater will completely process all the settings once until Sunday evening 24:00. If you want to repeat the set weekly schedule, press once again on the TIMER ON/OFF button. A symbol ][ will appear on the display. If you now press OK, the timer setting will be repeated weekly.

  • If you don’t select a time setting, then the heater will automatically select setting 01 after flashing approx. 14 times and the heater will completely process all the settings once until Sunday evening 24:00.
    Attention! All timer settings (maximum 10 per week) will be processed completely one by one. Therefore, make sure that they do not contradict each other!

  • If you wish, you can also readjust the thermostat, output and dimmer while the timer is working.

  • You stop the operation of the timer by pressing on the TIMER ON/OFF button. The heater will act as if there are no current timer settings and will simply operate according to the thermostat and output settings. By pressing the TIMER ON/OFF button again, you reactivate the timer setting.

  • To erase the timer setting, press on the TIMER SET button. 01 will start flashing on the display. Using the + and – buttons, look for the setting number that you want to erase and subsequently press on the C button (erasing the timer setting). The timer setting will disappear immediately.
    ATTENTION! If you want the heater to operate according to a timer programme, it will not only have to remain on stand-by, but also switched on (using the ON/OFF button). If this is not necessary, always switch off the heater using the ON/OFF button, switch off the main switch and remove the plug from the socket.
    ATTENTION! Day and time are deleted if the electricity is cut off. This happens not only when the plug is pulled out of the socket, but also if the main switch is set to O (OFF). The timer settings however are stored. When the electricity is restored and the timer settings are entered, then you need to reset the day and hour settings immediately; otherwise the time will begin at 0.00!
    If you do not enter any orders for approx. 15 seconds, the display will turn off. Pressing any random button will reactivate the display.

Switching off
If you are not using the heater, you must switch it off using the main switch (you press O) and remove the plug from the socket. Doing this will erases all the settings, also day and time. Only the timer settings are stored.

Safety feature

• The Valencia atmospheric fireplace is equipped with an overheating safeguard. In case of internal overheating, the overheating safeguard will switch the heater off. This may occur if the heater cannot give off enough heat or if it cannot draw in enough fresh air. As mentioned above, this is generally caused by (partially) covering the heater, obstructing the air intake and/or outlet grills or installing the heater too close to a wall or something similar. If this happens, turn the fireplace off by switching the main switch to O and remove the plug from the socket. Leave the fireplace to cool down for at least 15 minutes and remove the cause of overheating. You can then switch the fireplace back on.
• If the device overheats again or you cannot ascertain the reason for this, take the fireplace to your service point to be checked/repaired.
• Important! For safety reasons the fire will not automatically restart after overheating. Check whether conditions are safe before switching it on! So never switch on the heater by means of a timer and never connect it to a power supply that regularly switches on and off.

Cleaning and maintenance

• Always remove the plug from the socket and let the fireplace cool down before cleaning or touching.
• The Valencia atmospheric fireplace does not need much maintenance. Always keep the in- and outlet openings clean and dust-free.
• Use a soft cloth or a soft brush to clean the outside of the metal case. The glass plate can also be cleaned with a soft cloth. Do not use abrasive cleaning fluids or special glass cleaners!
• If the device malfunctions, immediately remove the plug from the socket and take to a service point. Do not carry out repairs yourself and always ask for original parts to be used. If the fireplace is to be stored after the winter period, clean it, pack it in original packaging if possible and store in a cool, dry and clean place. Make sure the fireplace is kept upright.

Problems and solutions

• If the fireplace will not work check the electrical supply. Is the socket working properly? Has the fuse blown?
• If the fireplace stops working suddenly, it may mean that the overheating safeguard has been triggered (see under ‘Safeguards’).
• In the event of other defects, immediately switch the fireplace off, remove the plug from the socket and consult a supplier or recognised electrician. Never carry out repairs yourself as this invalidates the guarantee and may be dangerous!

Disposal

At its end of life, discard the device according to the local laws and regulations, or deliver the device to your supplier.

References

• Eurom - Powerful products - producten voor comfort en gemak
• Eurom - Powerful products - producten voor comfort en gemak

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>