Nedis ASWI2614BK 4-Way Speaker Switch Box User Manual
- June 5, 2024
- nedis
Table of Contents
ASWI2614BK 4-Way Speaker Switch Box
User Manual
Preface
Thank you for purchasing the Nedis ASWI2614BK.
This document is the user manual and contains all the information for correct, efficient and safe use of the product.
This user manual is addressed to the end user. Read this information carefully before installing or using the product.
Always store this information with the product for use in the future.
Product description
The Nedis ASWI2614BK is a 4-way speaker switch box that allows the user to distribute the loudspeaker output of an audio amplifier to 4 pairs of speakers.
The 4-way speaker switch box is equipped with screw-type terminals for input and output connections.
The -way speaker switch box is equipped with spring-loaded terminals for input and output connections.
Intended use
The product is exclusively intended for distributing the loudspeaker output of an audio amplifier to passive speakers with an impedance load rated at 4 to 16 Ohms.
Any modification of the product may have consequences for safety, warranty and proper functioning.
Specifications
Product
|
4-Way speaker switch box
---|---
Article number
|
ASWI2614BK
Dimensions (l x w x h)
|
200 x 40 x 95 mm
Operating temperature
|
-25 °C – 85 °C
Storage temperature
|
-25 °C – 85 °C
Humidity
|
20 – 75% (RH)
Maximum load
|
200 W RMS per channel
Speaker impedance
|
4 – 16 Ohms
Cable type
|
Loudspeaker cable
Maximum cable cross-section
|
2.5 mm2
Maximum cable length
|
50 m
Parts list
1. Speaker pair 1 ON/OFF
2. Speaker pair 2 ON/OFF
3. Speaker pair 3 ON/OFF
4. Speaker pair 4 ON/OFF
5. Output for speaker pair 1 (Right)
6. Output for speaker pair 1 (Left)
7. Output for speaker pair 2 (Right)
8. Output for speaker pair 2 (Left)
9. Output for speaker pair 3 (Right)
10. Output for speaker pair 3 (Left)
10. Output for speaker pair 4 (Right)
10. Output for speaker pair 4 (Left)
10. Input from amplifier (Right)
10. Input from amplifier (Left)
Total impedance
- The total impedance of the connected loudspeakers is calculated from the series connection of speaker pair 1 and 2, as well as 3 and 4. These pairs in turn are connected in parallel.
Speaker pair operation
|
Total impedance with 8 Ohm speakers
---|---
Single speaker pair
|
8 Ohms
Two speaker pairs in series (e.g. 1+2)
|
16 Ohms
Two speaker pairs in parallel (e.g. 2+3)
|
4 Ohms
Three speaker pairs
|
5.3 Ohms
All speaker pairs
|
8 Ohms
None
|
220 Ohms
- If 4 Ohm loudspeakers are used, the provided total impedance values have to be halved.
Safety instructions
WARNING
- Only use the product as described in this manual.
- Do not use a damaged product.
- Do not expose the product to water or moisture.
- Do not drop the product and avoid bumping.
Installation
- Check the contents of the package
- Check the product for any visible damage. If the product is missing or damaged, contact the Nedis B.V. service desk via the website: www.nedis.com.
Connect the 4-way speaker switch box
- Make sure all the devices you want to connect have been turned off.
- Always comply with the operating instructions of the devices that you want to connect.
- Introduce the cables to the terminals neatly to exclude short circuits.
- Make sure that your amplifier can handle the total impedance of the setup of your speakers.
- Consult an audio specialist if necessary.
1. Connect the output terminals 5 and 6 for speaker pair 1 to the corresponding speaker.
2. Connect the output terminals 7 and 8 for speaker pair 2 to the corresponding speaker.
3. Connect the output terminals 9 and q for speaker pair 3 to the corresponding speaker.
4. Connect the output terminals w and e for speaker pair 4 to the corresponding speaker.
5. Connect the input terminals r and t to the loudspeaker output terminals of the amplifier.
Use
- Due to the series-parallel arrangement, the switches with no connected loudspeaker are always in the OFF position.
- Turn on your amplifier and play audio.
- Use the rocker switches 1, 2, 3 and 4 to select the desired speaker pair(s).
- Operate the volume control of your amplifier to adjust the overall volume.
Maintenance
- Clean the product regularly with a soft, clean, dry cloth. Avoid abrasives that can damage the surface.
- Do not use aggressive chemical cleaning agents such as ammonia, acid or acetone when cleaning the product.
Warranty
Any changes and/or modifications to the product will void the warranty. We accept no liability for damage caused by improper use of the product.
Disclaimer
Designs and specifications are subject to change without notice. All logos, brands and product names are trademarks or registered trademarks of their respective owners and are hereby recognized as such.
Disposal
|
This symbol indicates that this product should not be thrown away with other household waste throughout the EU. To prevent possible harm to the environment or human health by uncontrolled waste disposal, you are responsible for recycling it so that it can promote the sustainable reuse of raw materials. To return your used product, you can use the regular return and collection systems or contact the store where the product was purchased. They can recycle this product for the environment.
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>