ZENEC Z-E3766 Car Specific Infotainer User Manual

ZENEC Z-E3766 Car Specific Infotainer

COMPATIBILITY LIST

N-XFDUC8 device mounting frame kit required

CAUTION

• The installation of the ZENEC system should be carried out by an authorized installer. Specific knowledge and tools are required to do the installation. Incorrect installation can cause damage to the vehicle and the ZENEC system.
• Correct functioning can only be guaranteed when you use the ZENEC original accessories included in the kit or optionally available. The ZENEC system and the original accessories must under no circumstance be modified or altered in any way. Inappropriate actions can cause damage to the vehicle and the ZENEC system.

NOTE

• For the direct mounting, the target vehicle must be factory equipped with radio provision. The ZENEC system is not compatible with vehicles that are equipped with an OE radio or OE navigation system (10” / 9”) from the factory.
• These installation instruction manual applies to vehicle platforms appearing in the above compatibility list, and in a condition as offered by the respective vehicle manufacturer. Deviating equipment and specific adjustments to body battery-, vehicle battery, charging systems and power harness layout implemented by the given motorhome manufacturer brand are not taken into account in these installation instructions. Please contact the relevant motorhome manufacturer.
• The ZENEC system is equipped with an integrated DAB+ twin-tuner receiver. To make use of this you will need a suitable DAB antenna (not included in kit) that must be connected to the ZENEC system. If vehicle is equipped with ex-work OE DAB antenna, a FAKRA > SMB adapter is required for connection.
• In order to obtain better radio reception, it is recommended to equip the vehicle with an active FM / DAB roof mount car radio antenna system.
• If the target vehicle is equipped with a resistor based multifunction steering wheel (SWC), no additional accessories are needed to support the steering wheel remote control functions. (See step 8. for Bluetooth telephony function details)
• Software updates to the ZENEC system are installed with a USB memory device. Therefore when fitting the system make sure that the USB connection of the ZENEC system will still be accessible later (installation of an USB extension cable).
• If you have questions or problems relating to the ZENEC system, please contact the dealer from whom you purchased it.

THE KIT INCLUDES

| No.| Article| Qty|
---|---|---|---|---
1| Mounting frame| 1|
2| Remote control| 2|
3| Phillips screws| 4|
4| Parking brake cable| 1|
5| GPS antenna with metal mounting plate and double sided adhesive pad| 1|
6| USB extension cable| 2|
7| Bluetooth microphone with mounting accessories| 1|
8| 24-pin connection cable (4.2, M-Zone, AV-IN)| 1|
9| 20-pin connection cable (Mic, Cam, IR-IN, eCall Mute, Analog SWC-IN)| 1|
10| ISO-DIN main harness| 1|
11| Main device user manual| 2|
12| FM antenna adapter ISO/DIN| 1|
| 13| SWC-adapter (Key 1/2)| 1| |

TOOLS REQUIRED

• Torx screwdriver T25
• Phillips screwdriver
• Fabric tape

REMOVAL WORK AND PREPARATION

1. Mounting frame N-XFDUC8 with enclosed 4 pcs. M5 x 6mm screws.
2. The mounting frame N-XFDUC8 is pushed onto the X-F270 device via its back end.
3. The frame is affixed to the device applying two M5 x 6 mm screws an left and right side
4. Remove both storage compart- ments in accordance with the manufacturer‘s information.
5. Remove ventilation outlets L+R with appropriate tools.
6. Remove the 4 Torx screws and take out the original plastic holder frame.

INSTALLATION

1. Connect all cables previously routed into the radio slot and the original antenna cable to the ZENEC system. Additional antenna adapters, radio switch etc.

2. may be required. Depending on the features of your motorhome manufacturer these connections may vary.

3. Fit the GPS antenna (No. 5) at a suitable place, and make sure that the GPS reception is not adversely affected due to shadowing by me-tallic vehicle parts (thermal glazing etc.).
   Next run the connecting cable to the radio slot.

4. If you wish to use it, now fi t the external Bluetooth microphone (No. 7) supplied, and run the connecting cable to the radio slot.Depending on preference and your choice of an external or device-internal microphone, the microphone source for the Bluetooth mode must be correspondingly changed in the device menu.
   Run the USB extension cable (No. 6) from the radio slot to the position you want.

OPTIONAL

If your Car is equipped with a resistor based multifunction steering wheel you have to connect the enclosed SWC-adapter (No. 13) with the Main connection cable (No. 10) and the 20-pin connector on the vehicle side. The rear steering wheel buttons (3 buttons each on the left and right side) are connected via this adaptor cable. Change the SWC ASSIGNMENT of the ZENECS under SETTINGS > OTHER > SWC ASSIGNMENT at MODE 2.The SWC connection (buttons) is preset for Fiat Ducato III Series 8 models “Mode2“. Volume , Camera, Skip, BT, … are visually displayed at ZENECS on MODE 2 for you.The hands free Telephony (BT) is provided here by a
“double function assignment“. The front side Telephone & Voice buttons are only supported with an additional CAN IR Stalk Interface “N-XFDUC8-SWC1” Connect the main cable (No. 10) of the ZENEC system to the ISO plug connectors (illu. 4) of the vehicle. When using a reversing camera system, the reversing signal from the vehicle must be connected to the reverse connection of the ZENEC system for automatic switching.

ATTENTION
Playback of videos while driving is not permitted by law. For this reason the video playback function is blocked while the vehicle is moving / driving. Next slide the ZENEC with mounted N-XFDUC8 carefully into the radio slot until it heard to engage.

Attention!
Do not use the 2-part metal mounting frame No.3 for Series 8 here.

1. Fasten the mounting frame with the original 4 pcs Torx screws.
2. Insert back the ventilation outlets.

NOTE :

• Make sure that all connectors at the rear of the unit have sufficient room and are not bent.
• For vehicles with an original FIAT active antenna, it is necessary to ensure a power supply for the antenna. Pay particular attention that the plug connectors of the P.ANT lead of the main connection cable (No. 10) are connected together.
• Connectors without a retaining mechanism must also be secured with insulating tape.

COMMISSIONING
Make sure that the vehicle is outside, and that the GPS reception is not adversely affected by any shadowing (trees, high buildings etc.). Insert the seperately purchased navigation software SD card supplied into the SD card slot of the ZENEC system, and start it in order to establish a sat fix. Make sure that the vehicle is not moved until the sat fix is established. Now press the NAV button to start the navigation mode, and choose map view. Once your present location can be seen in the map view the sat fix will be automatically established. This can take 3 to 5 minutes. You can now use the ZENEC system.
Finally carry out a general functional test, and make the basic settings. Also ensure that no fault warnings appear on the vehicle side.

Electrical characteristics
Power supply: +12 V DC against vehicle ground
External protection against internal short-circuit: 15 A Mini-ANL fuse

Operating currents
The tables show the measured operating currents in different operating states. Measurements were taken with TFT brightness set to the factory setting „20“ for DAY operation. With the maximum possible TFT display brightness, the power consumption increases up by approx. 100 mA in the listed operating states.
All measurements were carried out on a stabilized 13.8 volt power supply operating voltage.

active playback,

output volume setting „0“

Navigation route calculation| 1,60 A| Route calculation in the navigation app,

output volume setting „0“

Reversing camera powered by device| 1,70 A| Reversing camera source, output

volume setting „0“

Media source

(FM, DAB+, USB, external source via AUX)

|

1,65 A*

|

Volume setting VOL „10“

Media source

(FM, DAB+, USB, external source via AUX)

| 1,90 A*| Volume setting VOL „20“
Media source

(FM, DAB+, USB, external source via AUX)

|

2,60 A*

|

Volume setting VOL „30“

CONNECTION DIAGRAM

References

• ZENEC – Touch another World

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>