Keychron V1 Knob Version Customizable Keyboard User Guide

Keychron V1 Knob Version Customizable Keyboard User Guide

Fully Assembled Version

Keyboard

• 1x Fully Assembled Keyboard

Including

• 1xCase
• 1xPCB
• 1x Steel Plate
• 1x Sound Absorbing Foam
• 1x Silicone Bottom Pad
• 4 Sets x Stabilizers
• 1 Set x Keycaps
• 1 Set x Switches

Cable

• 1x Type-C to Type-C Cable
• 1x Type-A to Type-C Adapter

Tools

• 1x Switch Puller
• 1x Keycap Puller
• 1x Screwdriver
• 1xHexKey

Barebone Version

Keyboard Kit

• 1x Keyboard Kit (Without Keycaps & Switches)

Including

• 1xCase
• 1xPCB
• 1x Steel Plate
• 1x Sound Absorbing Foam
• 1x Silicone Bottom Pad
• 4 sets x Stabilizers

Cable

• 1x Type-C to Type-C Cable
• 1x Type-A to Type-C Adapter

Tools

• 1x Switch Puller

• 1x Keycap Puller

• 1x Screwdriver

• 1xHexKey

QUICK START GUIDE

If you are a Windows user, please find the appropriate keycaps In the box, then follow the Instructions below to find and replace the following keycaps.

Mac / Windows

If you are a Windows user, please find the appropriate keycaps in the box, then follow the instructions below to find and replace the following keycaps.

1. Switch To The Right System

Please make sure the system toggle on the top left corner has been switched to the same system as your computer’s operating system.

2. The VIA Key Remapping Software

Please visit caniusevia.com to download the latest VIA software to remap the keys.
If the VIA software cannot recognize your keyboard, please reach out to our support to get the instruction.

3. The Layers

There are four layers of key settings on the keyboard. Layer O and layer 1 are for the Mac system. Layer 2 and layer 3 are for the Windows system.

If your system toggle is switched to Mac, then layer O will be activated.

If your system toggle is switched to Windows, then layer 2 will be activated. Remember that if you are using it in Windows mode, please make changes to layer 2 instead of the top layer (layer O ).
This is a common mistake people are making.

4. The Backlight

Press fn + Q to change the lighting effect

Press fn + tab to turn the backlight on/off

5. Adjust The Backlight Brightness

Press fn + W to increase the backlight brightness

Press fn + S to decrease the backlight brightness

6. Warranty

The keyboard is highly customizable and easy to be rebuilt.
If anything goes wrong with any of the keyboard components of the keyboard during the warranty period, we will only replace the defective parts of the keyboard, not the whole keyboard.

7. Watch The Building Tutorial On Our Website

If you are building the keyboard for the first time, we highly recommend you watch the building tutorial video on our website first, then start building the keyboard yourself.

8. Factory Reset

Troubleshooting? Don’t know what’s going on with the keyboard?

1. Try factory reset by pressing fn + J + Z (for 4 seconds).

2. Download the right firmware for your keyboard from our website.
   Remove the power cable from the keyboard.

3. Remove the space bar keycap to find the reset button on the PCB.

4. Hold the reset key while plugging in the power cable and then release the reset key. The keyboard now will enter DFU mode.

5. Flash the firmware with the QMK Toolbox.

6. Factory reset the keyboard again by pressing fn + J + Z (for 4 seconds).

• Step by step guide can be found on our website.

V1 CUSTOMIZABLE KEYBOARD SPECIFICATIONS

Specifications

Layout| 75%
Switch type| Mechanical
Width| 148.72mm
Length| 328.45 mm
Front height| 17.87 mm (without keycaps)
Back height| 25.84 mm (without keycaps)
Front height| 27.30 mm (with OSA keycaps installed)
Back height| 36.62 mm (with OSA keycaps installed)
Keyboard feet height| 2mm
Angle| 3.5 / 7.08 / 9.52 degree

V1 MECHANICAL KEYBOARD OVERVIEW

DEFAULT KEY LAYOUT:

LAYER 0: This layer will be activated when your keyboard’s system toggle is switched to Mac.

LAYER 1: This layer will be activated when your keyboard’s system toggle is switched to Mac and press the fn/M0(1) key.

LAYER 2: This layer will be activated when your keyboard’s system toggle is switched to Windows.

LAYER 3: This layer will be activated when your keyboard’s system toggle is switched to Windows and press the fn/M0(3) key.

KEY DESCRIPTION

Key Description

Ser-| Screen Brightness Decrease
Ser+| Screen Brightness Increase
Bright-| Backlight Decrease
Bright+| Backlight Increase
Prvs| Previous
Play| Play/Pause
Next| Next
Mute| Mute
Vol-| Volume Decrease
Vol+| Volume Increase
RGBToggle| Turn Backlight on/off
 RGBMd+| RGB Mode Next
RGBMd-| RGB Mode Previous
Hue+| Hue Increase
Hue-| Hue Decrease
RGBSPI| RGB Speed Increase
RGBSPD| RGB Speed Decrease
M0(1)| Layer 1 will be activated when holding this key
M0(3)| Layer 3 will be activated when holding this key

Third party input tools are not compatible with the keyboard.
Due to compatibility, versions, brands and drivers of Windows/macOS, functionalities of third Party input tools may be affected while using the keyboard. Please make sure your operating system and drivers are up to date.

Certain fn keys or multimedia keys does not work under Windows/ Android mode.
Functionalities of certain multimedia keys may be disabled due to compatibility, versions, brands and drivers of Windows/Android OS.

Safety Precaution:
Keep the product, accessories and packaging parts out of reach of children to prevent any accidents and choking hazards.
Always keep the product dry to avoid corrosion.
Do not expose the product to extreme temperatures below -10°C (5°F) or above 50°C (131 °F) to preserve the lifespan of the keyboard.

Keychron, Inc.
Dover, DE 19901, United States
Find us at:
https://www.keychron.com
Support@keychron.com
Facebook @keychron
Instagram @keychron
Twitter @keychronMK
Designed by Keychron
Made in China

Read More About……

Keychron V1 Knob Version Customizable Keyboard

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>