Keychron M3 Mini Wireless Mouse User Manual
- October 30, 2023
- Keychron
Table of Contents
Keychron M3 Mini Wireless Mouse
Overview
① CD Left button
② Right button
③ Middle wheel button
④ Forward button
⑤ Backward button
⑥ Mouse indicator
⑦ DPI button
⑧ Modes toggle0
⑨ Report rate button
⑩ 2.4GHz Type-A receiver
⑪ 2.4GHz Type – C receiver
Modes Of Connection
Wired Mode:
- When the mode switch is in “OFF” position, the mouse won’t respond if the cable is not connected.
- Connect the cable to the TYPE-C port of the mouse and the USB port on the device. The mouse is ready to use while the indicator lights up.
- When connected by cable, the mode will default to wired mode even if the toggle is in Bluetooth mode or2.4GHz mode.
GHz Mode:
-
Switch to “G” mode (2.4GHz mode), and the mouse will automatically turn on 2.4GHz paring. The mouse indicator will slowly flash green.
-
Find the 2.4GHz receiver and connect it to the device’s USB/Type-C port. Once successfully connected, the mouse indicator will tum green and stay on for3 seconds before dimming off. The mouse is now ready for use.
-
In 2.4GHz paring mode, the mouse indicator will slowly blink green for3 minutes. If the mouse is not connected within 3 minutes, the indicator will turn off. If you need to reconnect, hold both the “Left button+ Forward button” for4secondsto re-enter pairing mode.
- If you need to repair the connection in 2.4GHz mode, please unplugthe2.4GHz receiver first. Then, hold both the “Left button+ Forward button” for4 seconds, wait for the green light indicator to start flashing, and plug the 2.4GHz receiver back in to complete the pairing process.
Note: It is recommended that when pairing the M3 mini in 2.4GHz mode, the mouse should be within 20cm of the receiver.
simultaneously hold for4 seconds (to enter the forced paring mode)
Note: For the best wireless experience, we recommend using the cable and
putting the 2.4GHz receiver somewhere on your desk close to your mouse for a
lower rate of latency and Fewer signal interferences.
Bluetooth mode
- Switch to “B” Mode (Bluetooth), and the mouse will automatically turn on Bluetooth pairing mode. The mouse indicator will slowly flash blue.
- Open the Bluetooth settings, search for a device named “Keychron M3 mini”, then click “connect” to complete paring.
- When in Bluetooth pairing mode, the mouse indicator will slowly blink in blue for 3 minutes. If it’s not connected within 3 minutes, the mouse indicator will turn off. If you need to reconnect, you need to hold the “Left button+ Forward button” for 4 seconds to re-enter pairing mode. The indicator will slowly blink blue.
- If the M3 mini is in Bluetooth mode and needs to pair with a new device, hold both the “Left button+ Forward button” for4seconds and wait for the blue light to flash on. At this point, Bluetooth has re-entered pairing mode, and you can connect the new device to the M3mini.
simultaneously hold for4 seconds (to re-enter pairing mode)
Status indicator
2.4GHz Mode| The mouse indicator slowly blinks green – Ready to be paired.
The mouse indicator quickly blinks green – Pairing with the previous device.
---|---
Bluetooth Mode| The mouse indicator slowly blinks blue- Ready to be paired.
The mouse indicator quickly blinks blue- Pairing with the previous device.
Low Power| The mouse indicator will slowly blink red.
DPI indicator
White light 400DPI
Green light 800 DPI
Blue light 1600 DPI (default)
Yellow light 3200 DPI
Red light 5000 DPI
Report Rate indicator
*Report Rate= Polling Rate
White light 125hz (Default in Bluetooth mode)
Blue light 500hz
Red light lOO0hz (Default in wired &2.4GHz mode)
How to factory reset
Hold down both the “DPI” button and “Report Rate” button for4seconds,and all the LED lights on the mouse will blink. It will blink three times to indicate that the factory reset is successful.
simultaneously hold for4 seconds (starts factory reset)
Auto-sleep mode
Auto-Sleep mode will not be activated when in wired mode. When in 2.4GHz mode or Bluetooth mode, the mouse will go to Auto-Sleep mode after 15 minutes of sitting idle to save the battery. Move or click the mouse to wake it up.
Driver software
The Keychron M3 mini mouse driver can be downloaded from www.keychron.com. If the driver software can’t connect to the mouse, please contact us for technical support.
Charging indicator explanation
| Fully Charged | The mouse indicator will stay GREEN. |
|---|---|
| Low Power | The mouse indicator will slowly blink RED. |
- The mouse is compatible with all USB ports. For the best signal and charging speed, connecting to the USB3.0 port is recommended when charging or in use.
- If the mouse is connected by the USB Type – C cable when charging but not paired with any devices:
· The mouse indicator will stay RED when charging.
· The mouse indicator will stay GREEN when fully charged.
Note: The product supports up to SV charging voltage and 300 mA charging current. We are not responsible for any problems caused by improper recharging.
What’s in the box
Mouse x 1
USB Type-C receiver x 1
Extension Adapter x 1
User manaual x 1
USB Type – C to Type – C cable x 1
USB Type -A receiver x 1
USB Type -A to USB – C adapter x
Mouse Specification
Size: 1206539mm
Weight: 55 ± 3g
Report Rate(polling rate): 125(White) S00(Blue) – lO00(Red)
Sensor: PixArt 3395
Resolution: 100- 26000DPI
Mouse micro switches: Huano Micro Switch (80 million clicks life time)
2.4GHz/ Bluetooth connection range: Approx 10m of open space
Battery capacity: 600mAh
Usage duration: 70 Hours
Recharge time: 2 Hours
Charging port: USB Type – C
Connection mode: 2.4GHz- Bluetooth – Wired
Device name: Keychron M3 mini
Customer Service
Keychron, Inc.
Dover, DE 19901, United States
Find us at:
https://www.keychron.com
Support@keychron.com
@keychron
@keychron
@keychronMK
Designed by Keychron
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>