ADRIAN STEEL CHL4 Large Caulk Holder Instruction Manual
- June 5, 2024
- Adrian Steel
Table of Contents
ADRIAN STEEL CHL4 Large Caulk Holder Instruction Manual
PRODUCT FEATURES
Large caulk holder that holds 7 industrial size caulk tubes 2.75” diameter or smaller. Foam tape along bottom edge provides noise reduction. It is designed to be used in areas such as back doors, partition, etc.
PAGE 1 of 1
The information contained in this document is the sole property of ADRIAN
STEEL COMPANY. ADRIAN STEEL COMPANY retains the right to modify and/or change
the product of its design at any time without prior notification.
PRODUCT OVERVIEW
ITEM NO.| PART NUMBER| DESCRIPTION|
---|---|---|---
1| 65525-G| LARGE CAULK HOLDER 14″, GRAY| 1
2| 26650-0| Foam Tape, 0.25×2.5×40.0| 1
3| BAG65529| Bag For Short Caulk Holders| 1
4| 65527| Install Instr. For CHL4 & CHS5| 1
BEST PRACTICES
GET TO KNOW THE VEHICLE – AT THE BEGINNING OF ANY INSTALLATION, CHECK THE LOCATION OF THE FUEL TANK, FUEL LINES, BRAKE LINES, HIGH VOLTAGE BATTERIES AND WIRING HARNESSES TO AVOID INJURY OR PROPERTY DAMAGE FROM TOOL CONTACT.
SEAL ALL EXTERIOR HOLES – ALL INSTALLATION HOLES SHOULD BE SEALED WITH BUTYL TAPE OR SILICON TO PREVENT WATER AND EXHAUST GASES FROM ENTERING THE VEHICLE.
CONTROL DRILL DEPTH – TO AVOID DAMAGE TO THE VEHICLE, USE A DRILL STOP OR CLEARED STEP BIT WHEN DRILLING INSTALLATION HOLES.
ALWAYS ADD PRIMER – WHEN ADDING INSTALLATION HOLES BE SURE TO USE A SELF-ETCHING PRIMER TO PREVENT CORROSION, FASTENER FAILURE AND INJURY.
MOUNTING POINTS MUST HAVE METAL-TO-METAL CONTACT – USE PROVIDED MOUNTING SPACERS TO ACCOMMODATE FOR VEHICLE FEATURES, CARPET OR SUBFLOORS.
PROVIDE CLEARANCE FOR SPACERS – IF THE INSTALLATION VEHICLE CONTAINS A CARPET OR SUBFLOOR, USE A 1-3/16″ DIAMETER CARPET CUTTER (P/N: 31183-0) AT ALL MOUNTING LOCATIONS TO OPEN UP ROOM FOR SPACERS.
CHECK SPACER ORIENTATION – BE SURE THAT THE INDENT IN THE SPACER COVERS THE PLUSNUT HEAD; THIS ENSURES THE MOST METAL-TO-METAL CONTACT AND REDUCES VIBRATION.
PLUSNUT INSTALLATION – A PLUSNUT GUN IS RECOMMENDED FOR PLUSNUT INSTALLATION FOR ITS PRODUCTION SPEED. HOWEVER, A PLUSNUT SETTING TOOL CAN ALSO BE USED (P/N: 22200-0).
THRU-BOLT CLEARANCE – WHEN USING A THRU-BOLT AT ANY MOUNTING LOCATION, BE SURE THAT YOUR HOLE HAS 1/16″ CLEARANCE.
FASTENERS USED
-
FAS0438
5/16-18X.75 ZP SCREW, HFLNG QTY: 6 -
FAS0135
5/16-18 ZN NUT, HEX FLNG QTY: 6
BEGIN ASSEMBLY
-
STEP 1 – CUT FOAM STRIP TO 23″ & INSTALL ON BOTTOM LIP
-
STEP 2 – INSTALL HOLDER TO DOOR PANEL, PARTITION, ETC
PRODUCT SPECIFICATIONS
-
PRODUCT WEIGHT
7.5 LBS -
WIDTH x DEPTH x HEIGHT
23” X 4.39” X 10.58” -
CAPACITY
7 – 2.75 DIAMETER TUBES -
COLOR
GRAY -
CATALOG NUMBER
CHL7
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>