TEXAS PHX2000 Hedge Trimmer User Manual

TEXAS PHX2000 Hedge Trimmer

Warning

• Safety information about hazards that can result in personal injury.
• Please read the user manual carefully before operating the machine.
• Use ear protection, helmet, and eye protection.
• Use work gloves.
• Beware of falling objects, when cutting from above the head.
• Beware of an overhead electric power line. Keep a minimum 10 m distance.
• Do not expose the equipment to rain/water and store it indoors.
• Keep your distance to other people, children and animals.
• Must be recycled.
• Do not expose the equipment to extreme heat or fire.
• Do not expose the equipment to rain/water and store it indoor
• Please read the user manual carefully before operating the machine.
• Do not expose to temperatures above 45degrees C.
• Waste electrical products must not be disposed of with household waste. This tool should be taken to your local recycling center for safe treatment.

Spare parts

• Spare part drawings for the specific product can be found on our website www.texas.dk If you find the part numbers yourself, this will facilitate more rapid service. For the purchase of spare parts, please contact your dealer.

Safety

How to read the manual

Please read this instruction manual carefully, especially the safety warnings marked with the symbol: When using the product, the safety instructions must be, closely followed. Read this manual carefully before starting the machine. Make sure that you know how to stop and switch off the engine in case of an accident. All instructions regarding the safety and maintenance of the machine are for your own safety. The warnings, precautions, and instructions given in this manual, cannot cover all situations that the product can be placed in. The user must therefore present common sense and caution when using the product.

Safety in the work area

• Only use the product in clean and well-lit areas
• Do not use the product in areas with explosive danger or where there is flammable fluids, gas, or dust present.
• The person that uses the machine is responsible to the Mother person in the work area. Never use the machine when others, especially children or animals are near.
• This machine is an electric product. It is therefore important, that it never comes in contact with water or is used in wet surroundings.

Use and maintenance of the product

• This machine must not be used for other work than as described in this manual.
• Only use original spare parts. Mounting of nonapproved parts may lead to increased risk and are therefore not legal. Any liability is renounced for accidents or other damage that has happened due to the use of unauthorized parts.
• Before using the machine, the dealer or other qualified person should instruct you in the use of the machine.
• Minors may not work the machine.
• The machine may only be lent to people who know how to work the machine. This manual should follow the machine under all circumstances.
• The machine may only be used by persons who are rested, well, and fit. If the work is tiring, frequent brakes should be made. Do not use the machine under influence of alcohol.
• Always check before starting, that all bolts and nuts are tightened.
• Always wear eye protection when using the machine.
• Keep children and other persons at a distance of at least 5 meters from the work area.
• The battery should always be removed when:
  • maintenance is made.
  • the machine is left unattended
• During transport, the main switch must be switched off.

Identification of the machine and components

See Fig. 1+2

1. Blade
2. Lock for rotary head
3. Foam handle.
4. Hook harness
5. Rear handle
6. Safety switch
7. On/off switch
8. Extension lock
9. Locking collar
10. Battery
11. Battery release button
12. Display for remaining capacity
13. Push button for capacity display
14. Control lights
15. Battery charger
16. Harness

• Battery/charger are not included for solo machines.

Unpacking and assembly

1. Unpack all parts and lay them on a flat, stable surface.
2. Remove all packing materials and shipping devices, if applicable.
3. Make sure the delivery contents are complete and free of any damage. If you find that parts are missing or show damage do not use the product but contact your dealer. Using an incomplete or damaged product represents a hazard to people and property.
4. Ensure that you have all the accessories and tools needed for assembly and operation. This also includes suitable personal protective equipment.
5. Plug in the battery, by pushing it down until you hear a click
6. Remove the battery by pushing down the battery lock buttons and pulling up

NOTE: Always remove the battery before assembly and maintenance. Fig.2

Mount trimmer head on the telescopic shaft. See Fig. 3

1. Push the trimmer head down over the telescopic shaft.
2. Slide locking collar up to the trimmer head thread.
3. Tighten the locking collar (turn clockwise).

Battery

• Not included for solo machines

Warning

• Do not try to disassemble, short circuit, or put it to extreme heat or fire, as it can cause serious inquiry and permanent damage to the battery!
• The battery pack is not fully charged when delivered.

Charging

• Only use the original charger with art. no.90063242
• Before the battery is used the first time, it is recommended to fully charge it first.

LED 1, LED 2, LED 3

are lit.

| The battery pack is 50%-75% charged
LED 1, LED 2

are lit.

| The battery pack is 25%-50% charged.
LED 1 is lit| The battery pack is 0%-25% charged
LED 1 flash| The battery pack is empty.

Charge the battery.

Note: The indicator lights are only indicative indications, and is not accurate power indications.

Important: To protect the battery from total discharge, the machine will stop, when the battery is nearly empty.

• The machine must not be started up again after the automatic shutdown, as it can damage the battery.
• The battery must be recharged before the work can continue.
• For further information, see the user manual which is included with the battery.

Charger

A full charge takes around 60 min for a 2.0 Ah battery and 120 min for a 4.0 Ah battery.

• Only use the original charger*
• Do not try to charge another type of battery in the charger, other than the original batteries with art. no. 90063245 (2.0 Ah) or 90063246 (4.0 Ah).
• Keep the charger in a dry and warm environment] (10-25 degrees C) and only use it indoors. It should be connected to a normal 230V AC socket.
• Before the battery is used the first time, it is recommended to charge it fully.
• The surface of the battery can become warm during charging. This is normal.
• Do not cover battery or charger during charging. Allow free ventilation of air.
• Insert the battery into the charger slots and slide it into place until it locks.
• There are 4 lights on the charger indicating the status and state of charge of the battery.

Status

 |

Charging

 |

Fully charged

 |

Evaluate

 |

Defective

Important: The charger will stop when the battery is full. However, it is not recommended to leave the battery in the charger for more than 24 hours. It is recommended to drain the battery completely and fully charge it whenever possible, as it can increase the health of the battery. But partial charge will not damage the battery. To remove the battery from the charger, hold the button down and pull the battery out. Before winter storage, the battery should be fully charged and kept warm at 10-20 degrees C. Charge it every 3 months. Make sure to keep ventilation holes clean and free from dirt. Store the charger indoors between 5-25 degrees C.

Use

Fig. 2

Before use, make sure that the battery is fitted properly with the battery lock in place. To start the chainsaw, first press the safety lock (6) and then the On/off switch (7) to activate the chain saw. Stop the chain saw by releasing the on/off switch.

Fig. 4

The telescopic length can be adjusted between 0-67cm. To adjust the telescopic length, loosen the extension lock (8). Fig. 1.5 then adjust the telescopic shaft to desired length. IMPORTANT Remember to lock the lock extension again!

Clothing

When using the machine, wear tight-fitting work clothes, strong working gloves, hearing protectors, safety goggles, a helmet, and boots with non-skid soles.

Adjusting the angle of the cutting bar

Fig. 5

The angle of the cutter bar can be adjusted upwards in 1 position, to 0o (straight), and downwards in 4 positions to 90o. Totally 6 positions. To adjust the angling press the lock button for the rotary head (2) with your right hand, and with your left hand hold the motorhousing and bend it upwards/downwards to the desired position. When you hear a “click” the cutter bar has reached the correct position.

Tips and advice

See Fig. 6A

• Swing the cutter bar in an arc towards the outside of the hedge so that the cuttings are swept to the ground.

See Fig. 6B

• Cutting without standing directly next to the hedge, e.g. flowerbed between operator and hedge. Swing thecutter bar up and down in an arc as you move along the hedge – use both sides of the cutting blades.

See Fig. 6C

• Extra long reach without the need for other aids. Swing the cutter bar up and down in an arc as you move along the hedge – use both sides of the cutting blades.

See Fig. 6D

• Cutting close to the ground from a standing position, e.g. low shrubs. Swing the cutter bar back and forth in an arc as you move along – use both sides of the cutting blades.
  The hedge trimmer is not suitable for cutting grass!

See Fig. 6E

• Hold the pole hedge trimmer vertically and swing the cutter bar in an arc to make maximum use of its reach in height.

Maintenance

• Before any service and maintenance are done, the power must be disconnected, which means the battery is removed from the tool.
• Remove the battery before you clean and store the machine.
• For obtaining the best cutting results the knives must be cleaned and oiled regularly. Remove dirt with a soft brush and oil lightly.
• Use biodegradable oil.
• Clean the housing and other parts with a mild cleanser and a moist cloth. Never use aggressive cleansers or solvents.
• Prevent water from getting into the machine.

Storage

• Store the hedge trimmer dry and unavailable for children. Keep the blade lubricated. Use the transport protection when the machine is stored.

Specifications

Warranty terms and conditions

The warranty period is 2 years for private end users in countries. Products sold for commercial use, only have a warranty period of 1 year. The warranty covers the material and/or fabrication faults.

Restrictions and requirements

• Normal wear and replacement of wearing parts are NOT covered by the warranty.

Wearing parts, which are NOT covered for more than 12 months:

• Blade/bar
• Blade tip protector
• Battery: If the battery is not stored correctly (frost free and recharged every 3 months), the durability is only guaranteed for 6 months.

The warranty does NOT cover damages/faults caused by:

• Lack of service and maintenance
• Structural changes
• Exposure to unusual external conditions
• If the machine has been improperly used or overloaded
• Use of unoriginal spare parts.
• Other conditions where Texas cannot be held responsible.

Whether a case is a warranty claim or not is determined in each case by an authorized service center. Your receipt is your warranty note, why it should always be kept safe.

REMEMBER: The purchase of spare parts, as well as any request for warranty repair, art. number (e.g. 90063XXX), year, and serial number, should always be informed.

• We reserve the right to change the conditions and accept no liability for any misprints.

Troubleshooting

The hedge trimmer does not

| Battery not slotted in correctly?| Slot battery into place
Battery pack discharged?| Charging the battery pack
Battery pack defective?

Is the device defective?

| Contact Texas customer service or

service workshop

• For troubleshooting regarding battery and charger, see user manuals included for these items.

EC Declaration of conformity

Texas Andreas Petersen A/S

Hereby certifies that the following:

• Pole hedge trimmer battery.

PHX2000

• Is in compliance with the specifications of the machine directive and subsequent modifications.

2014/30/EU

• Conforms with the following standards

EN ISO 11680

• L: 91 dB(A)
• LpA: 84 dB(A)
• Vibrations Ah: 0.895 m/s2 (rear handle) / 0.778 m/s2 (front handle)

Serial numbers: 2201541001 – 2512549999

Texas Andreas Petersen A/S

• Knullen 22 DK-5260 Odense S

• 07.04.2022

• Johnny Lolk

• Managing Director

Responsible for documentation

• Johnny Lolk

References

• Salg af havemaskiner - Texas A/S
• Salg af havemaskiner - Texas A/S

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>