ADRIAN STEEL CCD12 Center Console Desk Instruction Manual

June 9, 2024
Adrian Steel

ADRIAN STEEL - logo CCD12 Center Console Desk
Instruction ManualADRIAN STEEL CCD12 Center Console Desk -
fig

PRODUCT WEIGHT
45 lbs.
WIDTH x DEPTH x HEIGHT
12.15 x 22.38 x 18.35
COLOR GRAY CATALOG NUMBER CCD12

CCD12 Center Console Desk

PRODUCT FEATURES
Center console desk is designed to be used with optional powerstrip, PA9, hanging file kit CCDHF12, and laptop holder CCDLTH
The information contained in this document is the sole property of ADRIAN STEEL COMPANY. ADRIAN STEEL COMPANY retains the right to modify and/or  change the product of its design at any time without prior notification.
Introduction / Comments:
This Center Console Desk is designed for storage of chargers, power strip, CCDHF12, CCDLTH, AND PA9.
Note:
It is advised that all fasteners used in this assembly and installation should be checked for tightness at the following intervals: @ 2-weeks and again @ 6-weeks of operation.  This preventive maintenance step must be completed to ensure your Center Console gives you long service life.ADRIAN STEEL CCD12
Center Console Desk CENTER CONSOLE DESK FOR MISC USE.

– PRECAUTIONS –

CAUTION
THE USE OF AIR IMPACT TOOLS CAN
OVER-TORQUE FASTENERS AND
CAUSE FASTENER FAILURE!


CAUTION
ALL INSTALLATION HOLES SHOULD BE SEALED ****
WITH SILICON OR BUTYL SEALANT TO PREVENT
EXHAUST FUMES FROM ENTERING THE VEHICLE!

DANGER
INSPECT FOR FUEL TANK, FUEL LINES, BRAKE LINES, HIGH
VOLTAGE BATTERIES AND ELECTRICAL LINES PRIOR TO
DRILLINGTO AVOID DAMAGING CRITICAL VEHICLE SYSTEMS
OR INJURY TO INSTALLER DURING INSTALLATION PROCESS!

CAUTION
TO AVOID DAMAGING THE VEHICLE ALWAYS
USE DRILL STOPS WHEN DRILLING ANY INSTALLATION HOLES!

IMPORTANT WARRANTY REQUIREMENTS

  1. SUBSTITUTING ADRIAN STEEL SPECIFIED FASTENERS FOR ASSEMBLY AND/OR INSTALLATION WILL VOID YOUR PRODUCT WARRANTY.
  2. ALL HOLES DRILLED INTO VEHICLE SHOULD HAVE THE RAW METAL EDGES SEALED WITH A SELF -ETCHING PRIMER TO RESIST CORROSION AND POTENTIAL FASTENER POINT FAILURE.
  3. ALL FASTENERS USED IN THE INSTALLATION OF THIS PRODUCT SHOULD BE TIGHTENED TO THE TORQUE(S) SPECIFIED IN THESE INSTRUCTIONS.
  4. THESE INSTRUCTIONS SHOULD BE KEPT WITH THE VEHICLE.

THE BASIC TOOLS NEEDED FOR MOST INSTALLATIONS

ADRIAN STEEL CCD12 Center Console Desk - TOOLS NEEDED ADDITIONAL TOOLS MAY BE NEEDED FOR THIS INSTALLATION AND THEY WILL BE IDENTIFIED IN THE STEPS THAT FOLLOW.
If your vehicle contains carpet or a rubber floor mat you will need to prepare the mounting location.
Position the product to be installed into the vehicle and once your are satisfied with the mounting locations, mark the mounting locations. Using a 1-3/16” diameter carpet  cutter (P/N: 31183-0). Select the appropriate floor spacers as shown in the illustration. Set those aside for use later into the installation process. Using the correct drill bit size  for the selected plusnut, drill the mounting holes in the vehicle sheet metal to prepare for installing the plusnuts.
If you are thru-bolting at any of the locations simply drill a hole that is 1/16” larger than the bolt size(s) for those locations.
Once you have drilled the holes into the vehicle,  the raw metal edges should be sealed using a self-etching primer to resist corrosion and potential fastener point failure. ADRIAN STEEL CCD12 Center Console Desk - point
failure

A PLUSNUT (RIVNUT) SETTING TOOL IS REQUIRED FOR PLUSNUT (RIVNUT) INSTALLATION AND IS SUPPLIED WITH THIS KIT. OR USE AN AIR POWERED PLUSNUT SETTING GUN.
1/4-20UNC Plusnut (FAS0052) Use 3/8” dia. drill w/stop
FAS0080 SCREW, HXHD, 1/4-20UNCx2.00”, G8
FAS0067 WASHER, FLAT, 1/4”ID
22200-0 PLUSNUT TOOLADRIAN STEEL CCD12 Center Console Desk - SETTING
GUN5/16-18UNC Plusnut (FAS0091) Use 1/2” dia. drill w/stop
FAS0095 SCREW, HXHD, 5/16-18UNCx2.00”, G8
FAS0086 WASHER, FLAT, 5/16”ID
22200-0 PLUSNUT TOOL
Place barrel of the plusnut body in sheet metal thru hole until flange is flush with sheet metal.
Using a 9/16” combination wrench of plusnut tool body and a second hand wrench, ratchet, or air tool, rotate the hex bolt head CW to draw plus nut flanges up (set the plusnut).

CCD12 CENTER CONSOLE DESK

ITEM NO.| PART NUMBER| DESCRIPTION| CCD12/QT
Y.
---|---|---|---
1| 37760-G| LID WELDMENT, CCD12| 1
2| 50045-G| BODY WELDMENT, CCD12| 1
3| HDWCCD12| CCD12 HARDWARE CARTON| 1
4| 25011-0| DECAL LID LATCHED| 1

ADRIAN STEEL CCD12 Center Console Desk - TOOLS NEEDED1

HDWCCD12
CCD12 HARD WARE KIT

ITEM NO. PART NUMBER DESCRIPTION HDWCCD12/QTY.
1 BAG50050 FAJENER BAG FOR CCD12 1
2 HDVV50050 HARDWARE BAG FOR CCD10 AND CCD12 1
3 44388 GROMMET,RUBBER, 1.5″ ID 3
4 35295-B MOLDED SLAM LATCH 1
5 CRT25386-1 HARDWARE BOX FOR CCD 1

ADRIAN STEEL CCD12 Center Console Desk - TOOLS NEEDED2

HDW50050 HARDWARE BAG FOR CCD10 & CCD12

ITEM NO. PART NUMBER DESCRIPTION QTY.
1 BAG0507-A 5″ x 7″ 3MIL AUTO BAG 1
2 FAS0137 Screw, Round Phillips Head, #6-3241375, Zinc plate 2
3 FAS0138 Nut Hex Flange, #6-32, Zinc Plate 2
4 34341-0 9309K16 MCMASTER CARR BUMPER 2
5 25384-0 SPRING CLIP, CCD 1
6 F AS0030 Screw, Round Phillips Head, #10-2441375 5

ADRIAN STEEL CCD12 Center Console Desk - TOOLS NEEDED3

BAG50050 FASTENER BAG FOR CCD12

ITEM NO. PART NUMBER DESCRIPTION QTY.
1 BAG0507-A .5″ x 7″ 3MIL AUTOBAG 1
2 FAS0020 Nut, Hex Flange, #10-24
3 FAS0091 Plusnut, 5/16 4
4 FAS0092 Screw, Hex Hd, 5/16-18×1.50 Zn Plate, G8 4
5 21166-0 ECCENTRIC WASHER 4
6 03927-1 Floor Spacer Short
7 03927-2 Tall Floor Spacer 4
8 FAS0098 Washer, Lock, Split, 5/16, Zinc Plate 4

ADRIAN STEEL CCD12 Center Console Desk - point
failure1

LID ASSEMBLY INSTALL

ADRIAN STEEL CCD12 Center Console Desk - TOOLS NEEDED4

INSTALL CENTER FILE, AND GROMMETS

ADRIAN STEEL CCD12 Center Console Desk - TOOLS NEEDED5

PRIOR TO INSTALLING LID, INSTALL ANY ACCESSORIES INSIDE CCD WITH INSTRUCTIONS SUPPLIED WITH ACCESSORIES.ADRIAN STEEL CCD12 Center Console
Desk - TOOLS NEEDED6

INSTALL INTO VEHICLE

ADRIAN STEEL CCD12 Center Console Desk - point
failure2 DOUBLE CHECK ALL FASTENERS LOCATIONS TO BE SURE THAT ALL
FASTENERS ARE TIGHTENED TO SPECIFICATIONS.
YOUR INSTALLATION IS NOW COMPLETE!
STOW THIS COPY IN THE VEHICLE FOR FUTURE REFERENCES!

ADRIAN STEEL - logo ADRIAN STEEL COMPANY
WWW.ADRIANSTEEL.COM
906 JAMES STREET
ADRIAN, MI 49221
800-677-2726

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals