ADRIAN STEEL TDC10 Promaster Tech Desk, 10” Instruction Manual

ADRIAN STEEL TDC10 Promaster Tech Desk, 10”

TDC10 – Promaster Tech Desk, 10″
PRODUCT WEIGHT
40 LBS
WIDTH x DEPTH x HEIGHT
10″ x 22″ x 19″
CAPACITY
USER DEFINED
COLOR
BLACK AND BLUE
CATALOG NUMBER
TDC10

PRODUCT FEATURES

TECH DESK CENTER CONSOLE DESIGNED FOR 2014 AND NEWER RAM PROMASTER (ALL HEIGHTS AND WEELBASES). CONSOLE COMES WITH A LOCKING LID, NON SLIP TOP TRAY, INTERNAL ELECTRONICS STORAGE SPACE, USB CHARGING PORTS, AND LIGHTS UP WHEN OPEN.

NOTE: INSTALLATION REQUIRES THE REMOVAL OF SOME VEHICLE AND FRONT DASH COMPONENTS.
The information contained in this document is the sole property of ADRIAN STEEL COMPANY. ADRIAN STEEL COMPANY retains the right to modify and/or change the product of its design at any time without prior notification.

Introduction / Comments

This Tech Desk Center Console is designed for storage of chargers, power strip, and miscellaneous electronics/items.
Note: It is advised that all fasteners used in this assembly and installation should be checked for tightness at the following intervals: @ 2-weeks and again @ 6-weeks of operation. This preventive maintenance step must be completed to ensure your Product gives you long service life.

WARNING! DISCONNECT THE VEHICLE BATTERY BEFORE STARTING THE INSTALL

NOTE : THE TDC10 IS DESIGNED TO ONLY WORK WHILE THE VEHICLE IS ON, THIS IS TO SAVE THE BATTERY FOR DYING IF A DEVICE IS LEFT PLUGGED IN.
NOTE: THE TDC10 WILL WORK WITH BOTH COMPOSIT AND STEEL PARTTIONS (AND STEEL PARTITION WITH LONG PARTS STORAGE) *SEE PAGE ** FOR DETAILS – IT IS RECOMMENDED THAT THE TDC10 IS INSTALLED BEFORE INSTALLING A PARTITION FOR EASE OF ASSEMBLY.

TECH DESK CENTER CONSOLE DESK FOR MISC USE.

PRECAUTIONS

|

CAUTION
THE USE OF AIR IMPACT TOOLS CAN
OVER-TORQUE FASTENERS AND
CAUSE FASTENER FAILURE!

|
---|---|---
|

CAUTION
ALL INSTALLATION HOLES SHOULD BE SEALED
WITH SILICON OR BUTYL SEALANT TO PREVENT EXHAUST FUMES FROM ENTERING THE VEHICLE

|
|

DANGER
INSPECT FOR FUEL TANK, FUEL LINES, BRAKE LINES, HIGH VOLTAGE BATTERIES AND ELECTRICAL LINES PRIOR TO DRILLINGTO AVOID DAMAGING CRITICAL VEHICLE SYSTEMS OR INJURY TO INSTALLER DURING INSTALLATION PROCESS!

|
|

CAUTION
TO AVOID DAMAGING THE VEHICLE ALWAYS
USE DRILL STOPS WHEN DRILLING ANY INSTALLATION HOLES!

|

IMPORTANT WARRANTY REQUIREMENTS

1. SUBSTITUTING ADRIAN STEEL SPECIFIED FASTENERS FOR ASSEMBLY AND/OR INSTALLATION WILL VOID YOUR PRODUCT WARRANTY.
2. ALL HOLES DRILLED INTO VEHICLE SHOULD HAVE THE RAW METAL EDGES SEALED WITH A SELF -ETCHING PRIMER TO RESIST CORROSION AND POTENTIAL FASTENER POINT FAILURE.
3. ALL FASTENERS USED IN THE INSTALLATION OF THIS PRODUCT SHOULD BE TIGHTENED TO THE TORQUE(S) SPECIFIED IN THESE INSTRUCTIONS.
4. THESE INSTRUCTIONS SHOULD BE KEPT WITH THE VEHICLE.

THE BASIC TOOLS NEEDED FOR MOST INSTALLATIONS

• DRILL

• DRILL BIT WITH STOP

• RATCHET, SOCKETS AND/OR WRENCHES
  

• SCREWDRIVERS

• MEASURING TAPE

ADDITIONAL TOOLS MAY BE NEEDED FOR THIS INSTALLATION AND THEY WILL BE IDENTIFIED IN THE STEPS THAT FOLLOW.

If your vehicle contains carpet or a rubber floor mat you will need to prepare the mounting location. Position the product to be installed into the vehicle and once your are satisfied with the mounting locations, mark the mounting locations. Using a 1-3/16″ diameter carpet cutter (P/N: 31183-0). Select the appropriate floor spacers as shown in the illustration. Set those aside for use later into the installation process. Using the correct drill bit size for the selected plusnut, drill the mounting holes in the vehicle sheet metal to prepare for installing the plusnuts.
If you are thru-bolting at any of the locations simply drill a hole that is 1/16″ larger than the bolt size(s) for those locations.
Once you have drilled the holes into the vehicle, the raw metal edges should be sealed using a self-etching primer to resist corrosion and potential fastener point failure.

A PLUSNUT (RIVNUT) SETTING TOOL IS REQUIRED FOR PLUSNUT (RIVNUT) INSTALLATION AND IS SUPPLIED WITH
THIS KIT. OR USE AN AIR POWERED PLUSNUT SETTING GUN.
1/4-20UNC Plusnut (FAS0052) Use 3/8” dia. drill w/stop
FAS0080 SCREW, HXHD, 1/4-20UNCx2.00”, G8
FAS0067 WASHER, FLAT, 1/4”ID
22200-0 PLUSNUT TOOL

5/16-18UNC Plusnut (FAS0091) Use 1/2” dia. drill w/stop
FAS0095 SCREW, HXHD, 5/16-18UNCx2.00”, G8
FAS0086 WASHER, FLAT, 5/16”ID
22200-0 PLUSNUT TOOL

Place barrel of the plusnut body in sheet metal thru hole until flange is flush with sheet metal.
Using a 9/16” combination wrench of plusnut tool body and a second hand wrench, ratchet, or air tool, rotate the hex bolt head CW to draw plus nut flanges up (set the plusnut).

TDC10–TECH DESK CENTER CONSOLE FOR PROMASTER

BAGTDC10 FASTENER BAG FOR TDC10

ADD FOAM STRIPS TO LAP TOP HOLDER (47891-B) AND FASTEN TO THE TDC10 WITH

FAS0238 (6)

REMOVE SEAT TRIM AND INSTALL FAS0052 1/4” PLUSNUT IN FRONT SEAT LOWER

BRACKETS

INSTALL FRONT MNTG BRKT ASS’Y (45693-B) BETWEEN FRONT SEATS USING THE

PLUSNUTS YOU JUST INSTALLED

DO NOT FULLY TIGHTEN, WAIT UNTIL THE CCD IS ATTACHED TO THIS BRACKET THEN FULLY TIGHTEN

INSTALL REAR MNTG BRLK ASS’Y (45690-B)

REMOVE FLOOR TRIM OVER HOLES IN BETWEEN REAR OF SEATS

INSTALL REAR MNTG BRLK ASS’Y (45690-B) CONTINUED

INSTALL TDC10 IN VEHICLE

INSTALL THE WIRE HARNESS—REMOVING TRIM

REMOVE FASTENERS TO REMOVE HAND BREAK COVER THE ON LEFT SIDE OF THE DRIVER’S SEAT.

REAR SIDE OF B PILLER TRIM

FRONT SIDE OF B PILLER TRIM REMOVE FASTENERS TO REMOVE THE B PILLER TRIM (DRIVER SIDE B PILLER TRIM)

REMOVE FASTENERS TO REMOVE TRIM BY FOOT WELL ON DRIVERS SIDE

IDENTIFY AND REMOVE FASTENER PLUGS FROM DRIVER SIDE FOOT WELL TRIM

REMOVE FASTENERS TO REMOVE FOOT WELL TRIM ON DRIVER SIDE.

AFTER ALL THE FASTENERS ARE REMOVED THE FOOT WELL WILL BE EXPOSED.

REMOVE FASTENERS TO REMOVE THE FUSE COVER TO THE BOTTOM LEFT OF THE STEARING WHEEL.

INSTALL THE WIRE HARNESS—ROUTING THE HARNESS

PLUG IN THE CONCETORS THAT GO OUT THE BACK SIDE OF THE TDC10

TUCK WIRE CONDUIT UNDER THE FLOOR MATT ALONG THE BACK OF THE DRIVER SEAT. SECURE WITH THE PROVIDE WIRE TIES WHERE NESSESARY

WIRE HARNESS SHOWN TUCKED UNDER THE MATT BEHIDE THE DRIVER SEAT.

CONTINUE TO ROUTE THE WIRE UNDER THE FLOOR MATT AROUND THE SIDE OF THE DIRVER’S SEAT

THE WIRE HARNESS WITH CONTINUE TO TRAVEL ALONG THE OEM CONDUIT AS SHOWN.

CONTINUE TO TUCK THE WIRE HARNESS INTO THE OEM CONDUIT THAT RUNS ALONG THE FOOT WELL.

MAKE SURE THE WIRE HARNESS RUNS UNDER THE FLOOR MAT.

CONTINUE TO RUN THE WIRE HARNESS ALONG THE OEM ROUTING, USING A SMALL FLAT HEAD  SCREWDRIVER TO OPEN THE SNAPS ON THE OEM CONDUIT.

THE WIRE ROUTING SHOULD LOOK LIKE AS SHOWN ABOVE, UTILIZING THE OEM ROUTING.

ONCE THE WIRE HARNESS IS ROUTED ADD ANY WIRE TIES AS NEEDED.

LOCATE OEM GROUNDING SCEW AND REMOVE TO ADD THE TDC10 WIRE HARNESS GROUND

REMOVE THE SCREW FROM THE OEM GROUND WIRE

ADD TDC10 GROUND WIRE TO THE OEM GROUND WIRE AND FASTEN BACK DOWN UNTILL TIGHT.

INSERT THE WIRE HARNESS THROUGH THE HOLE IN THE DASH THAT THE OEM WIRING FOLLOWS UP INTO THE FUSE PANNEL AREA. STRIP THE RED WIRE TO EXPOSE THE END AND CRIMP ON THE ADD-A-FUSE

REMOVE THE 5amp FUSE FROM THE UPPER LEFT ROW OF THE FUSE PANNEL.

PLACE THAT OEM FUSE INTO THE BOTTOM ADD-A-FUSE SPOT AS SHOWN.

ADD THE 10amp FUSE PROVIDED IN THE TDC10 WIRE HARNESS INTO THE TOP SPOT OF THE ADD-A-FUSE AS SHOWN.

NOTE : THE WIRE HARNESS INSTALLAIONIS COMPLETE, CONTINUE TO WIRE TIE ANY LOOSE WIRES TO FULLY SECURE THE HARNESS.

REASEMBLE ALL THE TRIM COMPONENTS IN THE ORDER THAT THEY WHERE TAKEN OFF IN.
NOTE: REASSEMBLE WITH CARE TO PREVENT BREAKING ANY COMPOENTS
YOUR INSTALLATION IS NOW COMPLETE

NOTE: THE TDC10 WILL ONLY HAVE POWER WHEN THE VEHCILE IS ON TO PREVENT DEAD BATTIERS FOR OCCURING.

DOUBLE CHECK ALL FASTENER LOCATIONS TO BE SURE THAT ALL FASTENERS ARE TIGHTENED TO SPECIFICATIONS.
YOUR INSTALLATION IS NOW COMPLETE!
STOW THIS COPY IN THE VEHICLE FOR FUTURE REFERENCES!

Documents / Resources

| ADRIAN STEEL TDC10 Promaster Tech Desk, 10” [pdf] Instruction Manual
TDC10 Promaster Tech Desk 10, TDC10, Promaster Tech Desk 10, Tech Desk 10
---|---

References

• Adrian Steel | Ladder Racks, Van Accessories, Storage | Vehicle Upfits

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>