ADRIAN STEEL HD-28NV2 HD Shelving Unit Instruction Manual

HD-28NV2 HD Shelving Unit
Instruction Manual

SHELVING UNIT 46H X 28W

HD-28NV2 HD Shelving Unit

CATALOG NUMBER HD-28NV2
PRODUCT APPLICATION
THIS SHELVING UNIT IS DESIGNED FOR THE NISSAN NV200 COMMERCIAL VEHICLE. THE SHELVING MAY APPLY TO OTHER VEHICLE APPLICATIONS (CONTACT ADRIAN STEEL ENGINEERING TO CONFIRM).

ACCESSORIES THAT WILL WORK WITH THIS PRODUCT

SPECIAL APPLICATION NOTES
NONE

The information contained in tsp. document is the sole property Of ADRIAN STEEL COMPANY ADRIAN STEE Company retains the right to modify and/or change the product of its design at any time without prior notification

PRODUCT WEIGHT
42 LBS.
WIDTH X DEPTH X HEIGHT
28 X 12 X 46
CAPACITY
44 LBS. PER SHELF
COLOR
GRAY
CATALOG NUMBER
HD-28NV2

PRODUCT FEATURES

HEAVY DUTY ADJUSTABLE SHELVING UNIT WITH TWO (2) EACH 12″ X 26″ X 2″ SHELVES AND ONE (1) EACH 12″ x 26″ x 4″ HEAVY DUTY SHELF. THE SHERLVES CAN BE ADJUSTED USING THE MOUNTING HOLES THAT ARE ON 1″ CENTERS.

SEE PAGE 2 FOR APPLICATION NOTES AND ACCESSORIES, OTHER PRODUCTS THAT WORK WITH THIS UNIT.

Assembly/Installation Instructions and Owners Manual
HD26NV2 & HD32NV2
HD SHELVING UNITS

PRECAUTIONS

| CAUTION
THE USE AIR IMPACT TOOLS CAN OVER-TORQUE FASTENERS AND CAUSE FASTENER FAILURE!
THE USE AIR IMPACT  TOOLS CAN OVER-TORQUE FASTENERS AND CAUSE FASTENER FAILURE!|
---|---|---
| CAUTION **
ALL INSTALLATION HOLES SHOULD BE SEALED WITH SILICON OR BUTYL SEALANT TO PREVENT  EXHAUST FUMES FROM ENTERING THE VEHICLE! ALL INSTALLATION HOLES SHOULD BE SEALED WITH SILICON OR BUTYL SEALANT TO PREVENT EXHAUST FUMES FROM ENTERING THE VEHICLE!|
|   DANGER
INSPECT FOR FUEL TANK, FUEL LINES, BRAKE LINES, HIGH VOLTAGE BATTERIES AND ELECTRICAL LINES PRIOR TO
DRILLINGTO AVOID DAMAGING CRITICAL VEHICLE SYSTEMS OR INJURY TO INSTALLER DURING INSTALLATION PROCESS!|
| CAUTION**
TO AVOID DAMAGING THE VEHICLE ALWAYS USE DRILL STOPS WHEN DRILLING ANY INSTALLATION HOLES!|

IMPORTANT WARRANTY REQUIREMENTS

1. SUBSTITUTING ADRIAN STEEL SPECIFIED FASTENERS FOR ASSEMBLY AND/OR INSTALLATION WILL VOID YOUR PRODUCT WARRANTY.
2. ALL HOLES DRILLED INTO VEHICLE SHOULD HAVE THE RAW METAL EDGES SEALED WITH A SELF -ETCHING PRIMER TO RESIST CORROSION AND POTENTIAL FASTENER POINT FAILURE.
3. ALL FASTENERS USED IN THE INSTALLATION OF THIS PRODUCT SHOULD BE TIGHTENED TO THE TORQUE(S) SPECIFIED IN THESE INSTRUCTIONS.
4. THESE INSTRUCTIONS SHOULD BE KEPT WITH THE VEHICLE.

THE BASIC TOOLS NEEDED FOR MOST INSTALLATIONS

ADDITIONAL TOOLS MAY BE NEEDED FOR THIS INSTALLATION AND THEY WILL BE IDENTIFIED IN THE STEPS THAT FOLLOW.

WHEN INSTALLING PLUSNUTS MAKE SURE YOU USE THE CORRECT DRILL BIT WITH A STOP!

NOTE: A PLUSNUT SETTING TOOL IS REQUIRED FOR PLUSNUT INSTALLATION AND IS NOT SUPPLIED WITH THIS KIT. ORDER PLUSNUT TOOLS FROM ADRIAN STEEL (P.N. 22200-0)OR USE AN AIR POWERED PLUSNUT SETTING GUN.
NOTE: If your vehicle contains carpet or a rubber floor mat you will need to prepare the mounting locations using a 1-3/16” carpet cutter.

1-3/16” DIAMETER CARPET CUTTER P.N. 31183-0.

| Step 01  Optional Based on Vehicle| If your vehicle contains carpet or a rubber floor mat you will need to prepare the mounting locations. (if not, skip to STEP 02)
Position the product to be installed into the vehicle and once your are satisfied with the mounting locations, mark the mounting locations. Using a 1-3/16” diameter carpet cutter. Select the appropriate floor spacers as shown in the illustration to the left. Set those aside for use later into the installation process.
Once you have prepared the carpet/floor mat for mounting, proceed to STEP 02.
---|---|---
| Step 02  Prepare Mounting Locations| Using a drill and drill bit (see table at top of page for correct size) drill the mounting holes in the vehicle sheet metal to prepare for installing the planets.
If you are thru-bolting at any of the locations simply drill a hole that is 1/16” larger than the bolt size(s) for those locations.
Once you have drilled the holes into the vehicle, the raw metal edges should be sealed using a self-etching primer to resist corrosion and potential fastener point failure.
| Step  03  Setting Planets| Use a Air Powered Planet Setting Gun to “set the planet” or if installing manually with hand tools, assembly the following. 1/4-20UNC Planet (FAS0052) FAS0080 SCREW, HXHD, 1/4-20UNCx2.00, G8 FAS0067 WASHER, FLAT, 1/4”ID 22200-0 PLUSNUT TOOL 5/16-18UNC Planet (FAS0091) FAS0095 SCREW, HXHD, 5/16-18UNCx2.00”, G8 FAS0086 WASHER, FLAT, 5/16”ID 22200-0 PLUSNUT TOOL Place barrel of the planet body in sheet metal thru hole until flange is flush with sheet metal. Using a 9/16” combination wrench of planet tool body and a second hand wrench, ratchet, or air tool, rotate the hex bolt head CW to draw plus nut flanges up (set the planet). Remove hex bolt, washer, and planet. Inspect installation.

PARTS YOU WILL USE FOR   STEP 04

HD26NV2 & HD32NV2
EP1246NV2, END PANELS
(2) REQUIRED| HD26NV2 & HD32NV2
EP1246NV2, END PANELS
(2) REQUIRED| HD26NV2 & HD32NV2
FAS0061, 1/4-20X.5 THP
(24) REQUIRED
---|---|---
| |
HD26NV2 & HD32NV2
AS0055, 1/4-20 NYLK NUT
(24) REQUIRED| HD32NV2
SF21232, SHELF
(2) REQUIRED| HD32NV2
SF41232, SHELF
(1) REQUIRED
| |

Instructions for Step 04

Determine the shelf positions for your installation and position the shelves to the end panels accordingly. Fastener the shelves to the end panels using two (2) each THP screws and the NY lock nuts at each corner to secure the shelf flanges to the end panel flanges as shown.
Ensure that the end panels are square to the shelves and fully tighten all of the fasteners.
For installing the shelves to the rail mounting kits in the vehicle refer to the installation instructions for the corresponding rail kits.

STEP 05 (Optional)
Add utility hooks

ADRIAN STEEL COMPANY
WWW.ADRIANSTEEL.COM
906 JAMES STREET
ADRIAN, MI 49221
800-677-2726

References

• Adrian Steel | Ladder Racks, Van Accessories, Storage | Vehicle Upfits

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>