anslut Outdoor Digital Power Strip Timer Instructions
- June 5, 2024
- anslut
Table of Contents
anslut Outdoor Digital Power Strip Timer
Important!
Read the user instructions carefully before use. Save them for future
reference. Jula reserves the right to make changes. For latest version of
operating instructions, see www.jula.com
SAFETY INSTRUCTIONS
- For outdoor use.
- Do not connect two or more timers together.
- Do not connect appliances that need a current of more than 8 A.
- Do not connect appliances with an output of more than 7800 W.
- Always check that the plug on the connected appliance is fully inserted into the socket on the timer.
- If the timer needs cleaning, unplug it from the mains and wipe it with a dry cloth.
- Do not immerse the timer in water or any other liquid.
- Do not connect heaters and other similar equipment to the timer.
- Check that the appliance to be controlled is switched off before plugging it into the timer.
Important
The timer must be placed in a vertical position to maintain the protection rating IP44.
SYMBOLS
| Read the instructions.
---|---
| Approved in accordance with the relevant directives.
| Recycle discarded product in accordance with local regulations.
TECHNICAL DATA
USE
BUTTON FUNCTIONS
CLOCK
Press CLOCK to switch from programming mode to show the time.
Press CLOCK together with SET to set the time and weekday.
Press CLOCK together with v-to switch to summertime.
CD
Press CD to start/stop countdown in AUTO mode.
RND
Press RND to start/stop random function in AUTO mode.
ON/OFF
Press ON/OFF to switch between ON, AUTO and OFF. Every time the button is
pressed the horizontal line moves between the markings ON-AUTO-OFF on the
casing.
SET
Press SET to set the time and weekday, or to confirm the setting.
A+
Press A+ to increase the value when setting programme, time or weekday.
v-
Press v-to decrease the value when setting programme, time or weekday.
S
Press at the same time CLOCK and v-to switch to summertime. The time is set
automatically forward 1 hour and S is shown in the display.
RESET
Press RESET once to reset all programme settings. If the display is em pty,
plug the timer into a power point and press RESET.
TIME DISPLAYING
The time can be shown with 12 or 24 hour displaying
- 12 hour displaying : The digits 00:00 to 12:00 are shown in the display together med AM or PM.
- 24 hour displaying: The digits 00:00 to 23:59 are shown in the display (AM/PM not shown).
- To switch between 12 and 24 hour displaying, press CLOCK until the display changes, Press CLOCK again to return to the original display mode.
NOTE
The timer battery is fully charged when the timer has been plugged into a
power point for two hours. H the display is empty, plug the timer into a power
point and press RESET.
SETTING THE WEEKOAY AND TIME
Setting the weekday
- Press SET until the weekday starts to flash
- Press A+ to increase the value, or v-to decrease the value as per:
- Press the buttons A+/v- once to step. Keep pressing the button to step faster. Release the button when the required value is shown in the display. Press SET to confirm.
Setting the time
- When the weekday has been set the value for hours starts flashing ..
- Press A+ to increase the value, or v-to decrease.
- Press A+/v- once to step. Keep pressing the button to step faster. Release the button when the required value is shown in the display. Press SET to confirm.
- The value for minutes fiashes. Set the minutes in the same way as the hours above.
Switching to summertime
- Press at the same time CLOCK and v-to switch to summertime. The time is set automatically forward 1 hour and S is shown in the display
- Press at the same time CLOCK and v-to switch back to normal time.
NOTE
The display must be in time mode when setting the weekday and time. If the
display is in programme settings mod et press the CLOCK button to switch to
time mode.
PROGRAMME SETTINGS
- When the display is in time mode, press A+ once to switch to programme settings mode – 10N is shown on the bottom left of the display.
- 7 is the programme number (possible values are 1 to 14).
- ON indicates weekday and time to start.
- OFF indicates weekday and time to stop.
- Set a higher programme number and ON or OFF with the button A+ as per: 10N➔70FF➔ .. 200N➔200FF➔ d ON/OFF (for countdown)➔.
- Set a lower programme number and ON or OFF with the button v – as per: ON/OFF (for countdown)➔200FF➔200N➔ … 70FF➔10N➔.
- Set the required programme number and then set weekday and time. Press SET until the weekday fiashes. Press repeatedly the button A+. The display changes as per
- MO TU WE TH FR SA SU
- MO➔TU➔WE➔TH➔FR➔SA➔su
- MO WE FR
- TU TH SA
- SA SU
- MO TU WE
- TH FR SA
- MO TU WE TH FR
- MO TU WE TH FR SA
- Press v – to step in the reverse order to the above.
- Press A+/v- once to step. Keep pressing the button to step faster. Release the button when the required value is shown in the display. Press SET to confirm. The displaying of weekday stops flashing.
- When the weekday has been set the value for hours starts flashing. Set the time as per the instructions in the section for setting the time.
- Repeat steps 2 to 7 to set more programmes
NOTE
When the required programme settings are ready, press CLOCK to return to time
mode. The display returns to time mode after 15 seconds if no buttons are
pressed.
SETTING THE COUNTDOWN
- When the display is in time mode, press v- once to switch to countdown settings mode. d ON (or d OFF) is shown on the bottom left of the display
- d indicates that countdown mode is active
- ON indicates time to start
- OFF indicates time to stop
- Press SET until ON/OFF flashes.
- Press A+/v-to select ON or OFF and press SET to confirm.
- The value for hours fiashes. Set the required value with A+/v- and press SET to confirm.
- The value for minutes fiashes. Set the required value with A+/v- and press SET to confirm.
- The value for seconds flashes. Set the required value with A+/v- and press SET to confirm. The possible values are 99:59:59 seconds to 1 second
- Plug the timer into a power point and set to AUTO mode to start/stop the countdown function.
- Press CD once to start the countdown. CD flashes in the bottom left of the display to shown that countdown is in progress. Press CD again to stop the countdown.
- If the display is in time mode during the countdown, press v- to show data for the countdown.
- When the required programme settings are ready, press CLOCK to return to time mode. The display returns to time mode after 15 seconds if no buttons are pressed.
RANDOM FUNCTION
- The random function starts and stops the connected appliance randomly.
- Shortest time switched off: 26 minutes
- Longest time switched off:42 minutes
- Shortest time switched on: 70 minutes
- Longest time switched on: 26 minutes
- Plug the timer into a power point and set to AUTO mode to start/stop the random function.
- Press RND to activate the random function. The time switched off is from 26 to 42 minutes and the time switched on is from 70 to 26 minutes.
- Deactivate the random function by pressing RND once.
- The random function disregards programme settings for start and stop.
DISREGARDING/RESUMPTION DF PROGRAMME SETTINGS
Press the ON/OFF button to disregard/resume programme settings.
- ON: Disregards programme settings, the connected appliance is on all the time.
- AUTO: The connected appliance starts and stops according to the programme settings.
- OFF: Disregards programme settings, the connected appliance is off all the time.
NOTE
- Programme settings and random function on are only active in AUTO mode.
- Programme settings and random function are not active in countdown mode.
- Programme settings and countdown function are not active in random function on mode.
CONECTION
- Set the required programme settings as described.
- Switch of the appliance to be controlled
- Plug the appliance into the timer and plug the timer into a power point.
- Start the appliance.
- The appliance starts and stops according to the timer settings, if disregard is not activated.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>