WISI LRPSA230 Plug-In Power Supply Charger Instruction Manual

Operating Instruction
WISI LRPS A230
Plug-in power supply 

for LR10 IN HOME FIBER TERMINATION with F connector

Safety and warning notes

Please read these user instructions before use the plug-in.
This switch mode plug-in changes mains alternating current to touch-safe low voltage and may be used only under the technical data listed below.
The switch mode plug-in is only designed for indoor use and should not come into contact with water or dust. To prevent overheating the power supply should not be covered when it is in use. Vibrations and special environmental factors on the device are inadmissible.
The main socket should be easily accessible. In the event of an operational error, the plug must be immediately removed from the socket.
The power supply is started up when the plug is inserted into the socket. To turn off the power supply, the plug must be removed from the socket. Never pull at the cable.
The power supply contains dangerous voltages and the cover should not be removed. All service or maintenance work should be carried out by qualified personnel who can get assistance by contacting the manufacturer’s agent. With visible damages to the device do not use this anymore.
An internal fuse protects the power supply against short circuiting in the primary circuit. In the event that the fuse needs to be replaced, the same type with the same breaking characteristic and size of the fuse should always be used.
The power supply is double-insulated (insulation class II) and needs no earth connector.
The power supply is provided with a DC cable and exclusively for powering LR10 IN HOME FIBER TERMINATION from the WISI Communications Company. One end of the DC cable is compressed with a special F-connector for screwing. A good assembly at the LR10 IN HOME FIBER TERMINATION, it prevents an unintended interruption of the DC power. The DC connector is to be connected to the input DC port of the LR10 IN HOME FIBER TERMINATION according to the instructions of the manual of the LR10 IN HOME FIBER TERMINATION.
Therefore the plug-in with the LR10 IN HOME FIBER TERMINATION forms a unit.
This switch mode plug-in has a plastic casing and shouldn’t contact with oils, grease, etc., as most types of plastic can be broken down by chemicals and solvents.
The Plug-in power supply is designated for the permanent operation in LR10.
PLEASE KEEP THIS INSTRUCTION IN A SECURE PLACE!

Technical Data

Max. Ausgangsleistung
Protection class system EN 60529 (DIN 40050)| IP 41
Electrical safety standard| EN 60065, EN 60950
EMC| EN 50083-2
Operating temperature range| 0…+40 °C
Storage temperature| -25…+70 °C
Dimensions (width x height x depth)| 60 x 24 x 41 mm

EU regulations for the disposal of old electrical appliances by private households
In order to avoid hazards to health and the environment, EU legislation specifies that affected products – identified by a crossed-out garbage bin on the product or its packing materials – may not be disposed of together with residual waste. You are responsible for ensuring that the appliance to be discarded is delivered to a location prepared to receive electrical appliances for the purpose of disposal or recycling (such as collection points for such products). Further information on the disposal of electrical appliances can be obtained from your local authorities, from the collection points, or from your local electrical appliance dealer.

WISI Communications GmbH & Co. KG
Empfangs- und Verteiltechnik
Wilhelm-Sihn-Strasse 5-7
75223 Niefern-Öschelbronn
Germany
HRA 700359

Inland: Phone +49 7233-66-0 Fax -320
Export: Phone +49 7233-66-280 Fax -320
Email: [email protected]
©WISI Communications GmbH & Co. KG
417766 a
wisigroup.com

Documents / Resources

| WISI LRPSA230 Plug-In Power Supply Charger [pdf] Instruction Manual
LRPSA230, Plug-In Power Supply Charger, LRPSA230 Plug-In Power Supply Charger, Power Supply Charger, Charger
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>