WISI DRC 17xx FLEXSWITCH Multiswitch Instruction Manual
- June 5, 2024
- WISI
Table of Contents
Operating manual
WISI FLEXSWITCH
DRC 17xx
Multiswitch 17 in x, cascade, TERR. passive
- Cascadable multiswitch for the distribution of 16 satellite polarisations and terrestrial signals
- Passive terrestrial path
- Integrated SAT amplifier for low insertion loss
- Pre-emphasis to compensate for the cable loss at high frequencies
- Terrestrial signals are available at the receiver without any power supply of the multiswitch
- High screening efficiency of Class A
- Compact dimensions paired with the installation-friendly distance between the F-connectors
- Color-coded inputs and outputs
- Made in Germany
Important Notes:
Please check the coaxial cables regarding the short circuit before starting! The mounting ground should be:
- flame retardant
- dust-free
- protected against humidity
- not under direct impact of sunlight
- not adjacent to heating sources
Please check the input level of the SAT lines: They should be nearly equal.
All installations and fixings of components should only be executed by skilled
people when the units are disconnected from the power source. Short-circuits
have to be avoided.
The European and national standards and regulations for the guarantee of
electrical security have to be considered as well as the national permissions
and legal regulations for broadcast receiving systems! A ground connection
must be installed at the device (Ground connector) as well as the satellite
dish with at least 4 mm² cables.
Grounding and Potential Equalization Pursuant to EN 50 083-1 the
satellite antenna system must comply with safety requirements, i.e.,
grounding and potential equalization.
Application:
This multiswitch is used for the distribution of 16 SAT-IF-Polarizations (e.g.
ASTRA, EUTELSAT, Türksat, and Hotbird) from four QUATTRO LNBs and terrestrial
signals (passive path). Depending on the type, max. 8, 12, 16, 24, or 32
subscribers/receivers can be connected to one unit, by using TV/SAT wall
outlets.
The selection of the IF-polarization is realized by the receiver control
signal 14/18 V (Vertical/Horizontal) , 0/22 kHz (Low-, High-Band). Selecting
the Satellite position is done by DiSEqC signals from the SATreceiver. Cascade
types can be powered by the external power supply unit DRP 1533 or through
SAT–trunk lines from connected multi switches or amplifiers (please consider
total current consumption). DC-blocks have to be considered to avoid power
conflicts.
Not used cascade outputs have to be equipped with DC-blocked terminating 75
Ohm resistors.
To increase the signal flatness, open subscriber outputs may be terminated by
a 75 Ohm resistor.
Application example:
Specifications
| SAT-IF trunk | DRC 1708 | – DRC 1712/1716 | DRC 1724/1732 |
|---|---|---|---|
| Inputs SAT | 16 St./16 pcs. | ||
| ‘Outputs SAT | 16 St./16 pcs. | ||
| ‘Frequency range SAT | 950…2400 MHz | ||
| Through loss SAT | 1…2 dB | 1…3 dB | 2…5 dB |
| decoupling SAT – SAT | 30 dB typ. | ||
| ‘Return loss SAT | . >10 dB |
Terrestrial trunk
Inputs TERR| | 1 St.// pcs.|
---|---|---|---
Outputs TERR| | 1 St.// pcs.|
Frequency range TERR| | 5…862 MHz|
Through loss TERR| 2…3 dB| 2…5 dB| 3…5 dB
Isolation TERR – SAT| | 30 dB typ.|
Return loss TERR| | >10 dB|
Subscriber outputs
| Outputs | 8 St./pcs. | 12/16 St./pcs. | ,24/32 St./pcs. |
|---|---|---|---|
| Frequency range | 5…2400 MHz | ||
| TERR type | passive/passive | ||
| Insertion loss SAT | 2…0 dB | 3…0 dB | 2…0 dB |
| Insertion TERR | 24 dB (±2 dB) | 28 dB (±3 dB) | 33 dB (±3dB) |
| Max. output level subscriber SAT | 102 dBpV | 102 dBpV | 102 dBpV |
| Max. output level subscriber TERR | 50…110 dBpV (passiv/passive) | ||
| Return loss subscriber SAT & TERR | >10 dB | ||
| Control signal | 14/18 V, 0/22 kHz, DiSEqC 1.0 | ||
| Current consumption from receiver | . 55 mA |
General data
| Power indicator | LED |
|---|---|
| Operating voltage | 15 V DC |
| Power consumption max. | <0,2 W |
| Screening factor | Klasse A, nach EN 50083-2/ |
Class A, according to EN 50083-2
Impedance| 750
Operating temperature range| -20…70 °C
Weight| 0,76…1,54 kg
Dimensions (width x height x depth)| 130x290x63 mm 189×291 x63 mm 310x293x63
mm
WISI Communications GmbH & Co. KG
Empfangs- und Verteiltechnik
Wilhelm-Sihn-Strasse 5-7
75223 Niefern-Öschelbronn Germany
Inland: Phone +49 7233-66-0 Fax -320
Export: Phone +49 7233-66-0 Fax -350
Email:info@wisi.de
Technical Modifications reserved. WISI cannot be held liable for any
printing error. / 08.17
wisigroup.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>