ZENEC ZE-RCE3701-MK2 Rear View Camera Brake Light Instruction Manual
- June 5, 2024
- ZENEC
Table of Contents
ZENEC ZE-RCE3701-MK2 Rear View Camera Brake Light
CONNECTION DIAGRAM
| COMPATIBLE WITH | MODEL TYPE | MODEL YEAR |
|---|---|---|
| Fiat Ducato III | X250/X251 | 2006 − 2014 |
| Fiat Ducato III | X290 | 2014 − 2021 |
| Fiat Ducato III | Series 8 | as of Q3 2021 |
| Citroën Jumper II | 250/250D/250DL | as of 2006 |
| Peugeot Boxer | 250/251 | as of 2006 |
TECHNICAL SPECIFICATIONS
- Image device: ¼” / 6.4 mm Aptina ASX340AT CMOS sensor
- Lens focal length: f 1.9
- TV system: NTSC / 60 fps
- View angle: 150°(D) x 130°(H) x 85°(V)
- Native sensor resolution: 720 (H) x 480 (V) pixels
- Resolution of video-out: > 420 TV lines
- Frame rate: 60 fields/sec.
- Signal to noise ratio: >48 dB
- Light sensitivity: 0.3 Lux
- Video output: 1.0 Vp-p, 75 ohms CVBS
- White balance: Auto
- Backlight compensation: Auto
- Gamma correction: 0.45
- Gain control: Auto
- Sync system: Auto
- Power supply: DC 6 – 24V
- Current consumption: 40mA (DC12V) / ≤ 480mW
- IP protection rating: IP69K
- Operating temperature: 30°C~+75°C, RH 95% max.
CAUTION:
Use the included connection cable exclusively. Altering or replacing it will
void your warranty.
The camera is water- and dustproof and has been licensed according to the
international standard IP69K. However, vehicle cleaning using high pressure
water and steam jet devices may still lead to damage of IP69K rated camera
models by water intrusion. Keep a distance of at least one meter between the
water nozzle and the camera housing.
KEY FEATURES
- Compact high resolution rear view camera for FIAT Ducato III vehicles and type variants
- System design integrating the original Ducato brake light retaining the road use homologation
- High quality Aptina CMOS picture sensor with low power consumption
- Detailed high contrast picture under twilight conditions
- 11 m main wire length
- Mechanically adjustable cam angle, allowing field of view personalization
- Plastic injection main housing with stainless steel fixation bolts
DESCRIPTION
This ZENEC rear view camera model has been developed for use with FIAT Ducato
III based vehicle and motor homes in particular. This camera product deploys
high quality parts and materials though out, to provide reliable operation and
appropriate longevity in the target vehicles mentioned.
The ZE-RCE3701-MK2 offers a large 150° diagonal viewing angle. The camera
complies with a great variety of moni- and naviceiver models made for CVBS
rear view cam signal input.
INSTALLATION
-
Loosen the two Phillips cross recess screws
-
Remove the brake light reflector housing
Un-connect the white system plug of the vehicle
-
Screw in and tighten the stainless steel mounting bolts by hand (5Nm). Use a dab of Loctite, if possible
-
Route the main cable from the naviceiver in the vehicle cockpit / dashboard to the brake light opening in the upper rear section of the vehicle. Fore power and RCA video signal, the ZENEC infotainer offers a direct system “connector block E” which offers switched 300mA power out’s (see installation guide of ZENEC head unit).
-
Connect the 3.5 mm jack output of the camera sensor to the green counterpart on the main wire and wrap around some isolating tape around it to prevent water entering the connector
-
Connect the system plug with the connector counterpart of the brake light reflector housing.
-
Re-mount the brake light reflector housing on top of the main camera housing, using the original Philips cross-recess screws
-
(no picture)
After connecting the main cable to the control unit in the dashboard > perform function test -
Alignment of the camera ball at the bottom side of the camera main body if necessary, using the supplied U-shaped tool
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>