Kruger Matz KM0490 Traveler K20 Bluetooth Headset Owner’s Manual
- June 5, 2024
- Kruger Matz
Table of Contents
Traveler K20
Bluetooth headset
KM0490
OWNER’S MANUAL
SAFETY INSTRUCTIONS
Read the instruction manual and safety instructions carefully before first use and keep them for future reference. Failure to comply with the below directions can cause a risk of product damage and/or user injury!
- Use only authorized accessories.
- Do not attempt to repair this device yourself. In case of damage, contact an authorized service point for check-ups/repair.
- Clean this device with a soft, slightly damp cloth. Do not use any abrasives or chemical agents to clean this product.
- Do not dispose of the device or its accessories in the fire.
- Protect this product and its accessories from moisture, humidity, water, and any other liquid. Avoid using/storing it in extreme temperatures. Do not expose it to direct sunlight and sources of heat. Do not store or use in a dusty environment. Avoid using it in a strong magnetic and strong static environment.
- Do not place magnetic storage media near the device. Radiation from the device may erase the information stored on them.
- This product is not a toy, do not allow children to play with this device or its accessories. Note: the device contains small parts which may pose a choking hazard!
- While using the headset, if the volume is excessively high it may cause hearing damage. Please adjust the volume of the player to a moderate level and balance the time of use.
- Discontinue using the device if you experience skin irritation or any other discomfort while using.
- DO NOT wear the headset when sleeping.
- When driving, you are advised to use the Bluetooth headset to ensure your driving safety. It is dangerous to directly use the phone when driving.
PRODUCT DESCRIPTION
- Increase volume/ Next track
- Decrease volume/ Previous track
- LED indicator
- Mute button
- micro USB port (charging)
- Multifunctional button (MFB)
- Microphone
BASIC OPERATION
Turn on/ off: Press and hold the MFB for about 3 seconds. A voice prompt
will be issued, LED indicator flashes blue once every 8 seconds.
The headset will automatically turn off if the pairing is not completed within
about 5 minutes.
Press and hold the MFB for about 4 seconds to turn off the headset. A voice
prompt will be issued, and the LED indicator flashes red two times, then goes
off. Mute microphone: Press the mute button once to mute. Press again to
unmute.
Factory settings: During charging, press and hold the MFB for about 4 seconds
until the LED indicator flashes blue.
CALL MANAGEMENT
Answer call: When there is an incoming call, you will hear a voice
prompt.
The LED indicator flashes blue once every 4 seconds. Press the MFB to answer
the call. During the call, the LED indicator flashes twice every 10 seconds.
End call: Press the MFB.
Reject call: When there is an incoming call, press and hold the MFB for
about 2 seconds.
Last number redialing: Press the MFB twice.
**Call switching*** : During the call, press and hold the MFB for about 2
seconds to transfer the call to the phone (LED indicator flashes red twice
every 10 seconds).
Press and hold the MFB again to switch it back to the headset (LED indicator
flashes to blue twice every 10 seconds).
- The phone must support the call switching function.
*Voice dialing:** Press and hold the MFB for about 1 second. - The phone must support the voice dial function.
MUSIC PLAYBACK MANAGEMENT
Play/ pause: Press the MFB once to pause music (LED indicator flashes
blue once every 8 seconds). Press the MFB again to play music (LED indicator
flashes blue twice every 8 seconds).
Previous/ Next track : Press and hold the – button for about 2 seconds to
go to the previous track. Press and hold the + button for about 2 seconds to
go to the next track.
Volume adjustment: Press the – button to decrease volume. Press the +
button to increase volume.
MULTI-POINT FUNCTION
- Pair the headset with device A, and then turn off Bluetooth function of device A.
- Turn off the headset.
- Turn on the headset again into pairing mode.
- Turn on the Bluetooth function of device B and connect with the headset.
- Turn on the Bluetooth function of device A; the headset will automatically connect with device A (device must support auto connect function); otherwise, pair the headset with device A manually. Now the Bluetooth headset has connected with devices A and B.
**MULTIPLE CALL MANAGEMENT***
- When a new call is incoming during the current call, press and holds the MFB until a sound is issued to reject the incoming call and keep the current call.
- Press the MFB once to answer the incoming call and end the current call.
- Press the MFB twice until a sound is issued to answer an incoming call and put the current call on hold.
- The function will operate properly if the phone supports multiple call management functions.
PAIRING
- With the headset turned off, press and hold the MFB for about 5 seconds, and the headset will turn on and automatically enter the Bluetooth paring mode (LED indicator flashes red and blue alternately).
- Please keep the headset and an external device close to each other while pairing.
- Enable the Bluetooth function on your external device and search for the headset (KM0490). For phones with Bluetooth versions lower than 2.1, you need to input a password “0000”.
- Connect with the headset.
- Successful pairing is signified by a voice prompt (when the devices are paired, a blue LED flashes once every 8 seconds).
Notes:
- If pairing is not completed within 5 minutes, the headset will automatically turn off. In that case, repeat the pairing process according to the instructions given above.
- Every time the headset is switched on, it will connect to the last connected device automatically. Please note, that your device must be on with the Bluetooth function turned on.
- When the devices are paired but the operating distance between them is exceeded, you will hear a voice prompt and the devices will disconnect. The Voice prompt will sound every 15 seconds. If the devices re-enter the operating distance within about 10 minutes, they will pair automatically. Otherwise, the headset will turn off.
CHARGING
- Connect one plug of the micro USB cable into the micro USB port of the headset.
- Connect the other plug into an AC charger or compatible PC USB port.
- The red indicator is on when the headset is charging.
- It takes about 2 hours to fully charge the headset.
- When the battery is fully charged, the blue indicator is on.
Notes:
-
When the battery level is low, the LED indicator flashes red twice every 8 seconds.
In that case, use the supplied micro USB cable to charge the device. -
The headset will automatically turn off when plugged into a charger.
-
Fully charge the headset before first use.
-
The producer recommends using only supplied/authorized charging cable.
-
The battery is non-removable. Do not attempt to remove the battery from the headset; otherwise, the headset may be damaged.
-
A fully charged battery can provide up to 7 hours of talk time and 5 days of standby time. The actual talk time and standby time may vary with different settings, ways of usage, and environments.
CLEANING AND MAINTENANCE
- Clean the device and its accessories using soft and dry cloth.
- Do not use any abrasives or chemical agents to clean this product.
- Store the device turned off and safely protected.
- If the headset is not used for a long time, store it in a dry and well-ventilated place.
TROUBLESHOOTING
| Problem| Possible reason| Possible Solution
---|---|---|---
1| Phone cannot find the headset| The headset is not turned on| Turn off the
headset, then press and hold the MFB for not less
then 4 seconds until the LED indicator flashes red and blue alternately
(paring mode)
Headset error| Restore factory settings (see Basic operation section)
Phone error| Reconnect the car charger
2| No sound from
the headset| The volume of the phone is too low| Increase volume of the phone
---|---|---|---
The headset and phone are not connected properly| Follow the instructions
given in the Pairing section to pair the
devices properly
The headset is out of the operating
range| Make sure the devices are within 10 meters from each other
3| Charging red
indicator doesn’t
light on| The headset has not been used for
a long time| Charge the headset for about 30 minutes and afterward, the red
LED may light on
SPECIFICATION
Bluetooth profiles: A2DP/AVRCP/HFP/HSP/Multipoint (Simultaneous connection
with two phones)
Talk time: up to 10 h
Standby time: up to 7 days
Charging time: approx. 2 h
Noise cancellation
Voice guidance and notifications
Voice dialing
Multiple call management
Supports music control
Bluetooth version: 5.1
Bluetooth range: up to 10 m
Ports: micro USB port (charging)
Compatibility: Devices supporting Bluetooth function
Comfortable and secure attachment on any ear
Battery: 90 mAh
Power supply: 5 V, 500 mA
In the set: micro USB cable, ear tips (x3), foam ear tip cover (x3), user’s
manual
Lechpol Electronics Leszek Sp.k. hereby declares that Bluetooth headset KM0490
is consistent with directive 2014/53/UE. The full text of the EU Declaration
of Conformity is available at the following Internet address: www.lechpol.eu.
\
****Correct Disposal of This Product
(Waste Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate
collection systems) This marking shown on the product or Its literature
indicates that It should not be disposed of with other household wastes at the
end of its working life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate this from other types
of waste and recycle it responsibly to promote the sustainable reuse of
material resources. Household users should contact either the retailer where
they purchased this product, or their local government office, for details of
where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract This product should not be mixed with
other commercial wastes for disposal.
Made in China for Lechpol Electronics Leszek Sp.k., ul. Garwolińska 1, 08-400
Miętne.
http://www.krugermatz.com/
www.krugermatz.com
is a registered trademark
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>