PARMIDA PLED-DISK5 5-Inch and 6-Inch LED Disk Light Installation Guide

: June 5, 2024
: PARMIDA

PARMIDA PLED-DISK5 5-Inch and 6-Inch LED Disk Light

PARMIDA PLED-DISK5 5-Inch and 6-Inch LED Disk Light
product

IMPORTANT

When using electrical equipment, basic safety precautions should always be followed as below

All electrical connections must be in accordance with local and National Electrical Code (N.E.C) standards.
If you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician.
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
To prevent wiring damage or abrasion do not expose wiring to edges of sheet metal or other sharp objects.
Suitable for damp locations.
Suitable for Type IC or suitable for Type non-IC.
Use only in open luminaires.
This device is not intended for use with emergency exit.
UNPACKING thoroughly inspect the light for freight damage. Freight damage should be reported to the delivery carrier.

INSTALLATION TYPES

Surface mount with junction box or retrofit recessed can.
This light is dimmable.
Dimming range is 10%-100%.
This retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction.
Please examine all parts that are not intended to be replaced by the retrofit kit for damage and replace any damaged parts prior to installation of the retrofit kit.
Only install in operating environments between -4°F and 113°F -20°C and +40°C.

SELECTING COLOR TEMPERATURE

To avoid risk of damage, ensure wall switch connected to the light is turned to off position before changing or selecting desired color temperature (CCT) on the selector switch. Select the color temperature via the CCT switch located on the face of the light when the lens has been removed. Using the color (CCT) selector switch, select the desired color temperature (3000K Soft White, 4000K Cool White, or 5000K Day Light.

SURFACE MOUNT JUNCTION BOX

Make sure power is turned off at the source before installing the light and the J-box is securely mounted.
This light is compatible with 2.75, 3.5 or 4 J-box.
Remove lens by twisting clockwise.
Remove the two stickers at the back that read as 2.75,3.5 or 4 junction box installation hole to reveal 6 screw slots.
Connect the supply wires to the wires on the light using the three wire nuts included in the packaging. Attach white to white and black (red) to black by pushing the wires into the wire nuts. Also attach copper wire to copper wire (green) as grounding connection using the wire nut.
Arrange the wires in the back of the junction box.
Align appropriate holes in the mounting light with the holes in the J-box depending on the size of the box 2.75, 3.5 or 4.
Use the longer screws for a deep J-box or the shorter screws for a shallow J-Box to attach the mounting light, flush with the ceiling.
Do not over tighten screws or light will not be tight to ceiling.
Complete the installation by placing the lens back into it’s original position by twisting it in counter clockwise direction.

STEP 1

STEP 2

STEP 3

PARMIDA PLED-DISK5 5-Inch and 6-Inch LED Disk Light 3

STEP 4

PARMIDA PLED-DISK5 5-Inch and 6-Inch LED Disk Light 4

STEP 5, 6 & 7

PARMIDA PLED-DISK5 5-Inch and 6-Inch LED Disk Light 5

STEP 8

PARMIDA PLED-DISK5 5-Inch and 6-Inch LED Disk Light 6

RETROFIT

Make sure power is turned off at the source before installing the light.
Remove any existing trim prior to installation of this light.
Remove lens by twisting clockwise.
Peel off the two stickers at the back that read as 5” or 6” recessed installation hole to reveal 2 rectangular slots.
Place the spring holds into these rectangular slots and twist them at right angle in a locked position.
The spring holds must be adjusted depending on the can size (5” or 6”) as shown in figure.
Connect the power wires from the E26 Adapter to the wires on the light using the two wire nuts included in the packaging. Attach white to white and black (red) to black by pushing the holds into the wire nuts.
Thread the E26 Adapter into the socket of the recessed can.
Squeeze both the holders arms together and insert into the spring slots of the can.
Arrange all wires and carefully push the retrofit trim into the can.
Complete the installation by placing the lens back into it’s original position by twisting it in counter clockwise direction.

COMPATIBLE DIMMER LIST

DIMMING

Dimming performance may depend on the dimmer, the dimmer range adjustment setting for dimmers with brightness range adjustments, the wiring method, and/or the number of LED modules installed onto the dimmer circuit. For dimmer selection, Dimming Control Manufacturers revise their product often for the latest list of compatible dimmers please visit our website. For best results, it is recommended to install a minimum of four LED modules onto one dimmer. Before turning on the LED lights, set dimmer position at maximum before adjusting to a lower light level. Please follow the Dimming Control Manufacturer’s instructions for the installation of all dimming controls.