MIONBEL N5 MP3 Bone Conduction Headphones for Swimming User Manual

MIONBEL N5 MP3 Bone Conduction Headphones for Swimming

PRODUCT INTRODUCTION

PRODUCT PARAMETER

FIRST USE
Before the first use, please confirm that the headset is fully charged. When the power iS insufficient, please use the charger to charge the device.

ON/OFF
Power on: in the power-off state, long-press the MFB Button for 3 seconds to turn on the headset.
Power off: in the power-on state, long-press the MFB Button for4 seconds, and the headset will be disconnected and turned off.

BT PAIRING
Hold the headphone MFB button for 3 seconds to enter pairing mode, and open the device BT menu and search for “Mionbel N5 MP3” to click connect. Prompt Tone: Connected.

RESTORE FACTORY SETllNGS

When the headphone and the device cannot be paired, please follow these steps to reset:

1. Please delete the pairing with “Mionbel NS MP3” headphones in your device first
2. In the headphone off state, hold the MFB button for 10 seconds, after the prompt “enter BT and wait for connection” appears for second time, the LED indicator flashes red and blue to re-enter the pairing state.
3. After resetting the headphone, the previous pairing information of the headphone has been cleared, please follow the “BT PAIRING” procedure to reconnect.

OTHER FUNCTIONS

Timeout not connected
If the headset is not successfully connected to the device within 5 minutes In the state of waiting for pairing, It will automatically shutdown

BT disconnect
After the connection is successful, if the BT of the mobile phone is turned off or exceeds the effective connection distance of BT (10m in barrier-free environment), the BT will be disconnected. If the device is not connected within 5 minutes, it will be automatically tuned off.

KEY OPERATION

Music playing

• Play/ pause Music: cllck the MFB button
• Previous song: long press volume-
• Next song: long press volume+
• Volume-: click volume-
• Volume +: click volume+

Call management
Answer I end a call: click the MFB button Reject incoming call: long press the MFB button for 2 seconds

Mode switching
Mp3 / BT mode: double click the multifunction key

Voice control
Press and hold the M FB button for 2 seconds (this function needs to be supported by the mobile phone)

MEMORY FILE UPDATE

Plug in the random USB cable and connect to the computer. The headset wlll give a prompt tone “enter USB flash drive”. At this time, the corresponding mobile drive letter can be found on the computer, and the U-drive function can be executed to update MP3 songs

HEADSET BATTERY LEVEL AND CHARGING

Headset power display
The status bar of the mobile phone can display the power Information of the headset device (this function needs to be supported by the mobile phone version)

Headset charge state
During the charging process of the headset, the indicator light will have a charging prompt, and the Indicator light will be on for a long time after It Is fully charged.

Headset low battery reminder
When the headset is in the low battery state, the voice prompts “battery low” once every 80s. Please charge the headset in time.

INDICATOR STATUS

Headphone Indicator

1. Start up: the blue light is on for 2S, and the blue and red lights flash alternately
2.  Shutdown: the red Ilg ht Is on for 2S and then goes out
3.  Pai ring status: red and blue lights flash alternately
4.  Successful connection: blue light 5S flashes
5.  Music status: blue light 5S flash
6.  Call status: blue light flashes twice in 5S
7.  Low battery: the red light flashes for 5S
8.  Charging state: the red Ilg ht Is on for a long time
9.  Charging completed: the blue light is on for a long lime

SCHEMATIC DIAGRAM OF HEADSET CHARGING

SAFETY PROBLEM

1.  Since there is a battery in the headset, please try to keep the product away from high-temperature areas.
2.  Please try to use qualified chargers and charging wires, and try to avoid charging this product with substandard equipment.
3.  The waterproof grade of this product is I P68. Please choose a suitable scene to use this product.

INVENTORY

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.  This device may not cause a harmful interface, and
2.  This device must accept any interference received, including interference that may cause undesired operation.

Warning:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

NOTE:
This equipment has been teated and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfaces in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect that equipment into an outlet 011 a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/1V technician for help.

RF warning statement:
The device has bean 8’111luated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>