PARMIDA PLED-PDN12W27K LED Ultra-Thin Ceiling Light Installation Guide

: June 9, 2024
: PARMIDA

Table of Contents

LED ULTRA-THIN CEILING LIGHT IMPORTANT : Please read carefully and
COMPATIBLE DIMMER LIST
STEPS FOR INSTALLATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PARMIDA PLED-PDN12W27K LED Ultra-Thin Ceiling Light

LED ULTRA-THIN CEILING LIGHT IMPORTANT : Please read carefully and

save these instructions, as you may need them at a later date. When using electrical equipment, basic safety precautions should always be followed as below:

Before beginning installation, ensure power is turned off at the main breaker.
Ensure your eyes are properly protected

GENERAL: All electrical connections must be in accordance with local and National Electric Code (NEC) standards. All electrical connections, installation and service should be performed by a qualified licensed electrician.

READ AND FOLLOW BELOW SAFETY INSTRUCTIONS
To prevent wiring damage or abrasion do not expose wiring to edges of sheet metal or other sharp objects.
Supply conductors (power wires) connecting the fixture must be rated minimum 90˚C. If uncertain consult an electrician.
Type IC Rated for direct contact with insulation.
This light is dimmable. Please refer to our website for the most up-to-date compatible dimmer list.
REQUIRED TOOLS : (not included) Safety glasses and gloves, tape measure, saw, pencil/pen.
UNPACKING : Thoroughly inspect the fixture for freight damage. Freight damage should be reported to the delivery carrier.

COMPATIBLE DIMMER LIST

DIMMING| LUTRON|
---|---|---
Dimming performance may depend on the dimmer, the dimmer range adjustment setting (for dimmers with brightness range adjustments), the wiring method, and/or the number of LED modules installed onto the dimmer circuit| AYCL-153P
CLDVSL-153P-WH
CT600P| 6674
6681
1G44I1
For dimmer selection, Dimming Control Manufacturers revise their product often; for the latest list of compatible dimmers please visit our website| CTCL-153P
DV600P| 1PL06
6672-1LW
Please follow the Dimming Control Manufacturer’s instructions for the installation of all dimming controls| DVCL-153P
IPL06
MACL-153M| 6672-DECORA
DSL06
The absence of a dimmer from this chart does not necessarily imply incompatibility| PD-6WCL S600-P| DSM10-DECORA
Please vi s it our website www.parmida.com or contact our customer support team for more details| SCL153P TG-10P TG600P TGCL-153P|

STEPS FOR INSTALLATION

RETROFIT: If there is an existing hole, make sure that it is the correct size (4.1in/105mm for 4” model & 5.9in/150mm for 6” model) for the luminaire to properly fit. If applicable, remove any existing retrofit can.
NEW INSTALLATION: If there is no existing hole, cut a new hole using the provided hole template. Place template over the desired location.
Trace the outer ring with a pen or pencil (not included). Cut the opening with a saw (not included).
Open the cover of the remote driver box. Push and remove one of the knockouts on the side plate.
Locate power supply leads from remote driver box and connect to power source using push connectors (provided).
Connect black wire to live wire, white wire to neutral wire, and green wire with ground (as shown) and secure using push connectors. Close the cover of the box.
Connect the remote driver box to the luminaire and tighten the nut connector by hand.
Place remote driver box through the cut-out hole. If remote driver box needs to be attached, use provided keyhole fittings on the back of the box to hang it using round head screws (not included).
Pull the spring clips on the fixture up and through the ceiling hole and place luminaire in the hole making sure the spring clips are holding securely.
Turn the power back on. If the luminaire doesn’t illuminate within 5 seconds, turn power off, carefully remove the luminaire and double check all wiring.

WARNING
RISK OF FIRE OR ELECTRIC SHOCK DISCONNECT MAIN POWER AT FUSE OR CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING THE LIGHT DO NOT PLACE YOUR HAND UNDERNEATH SPRING CLIPS DURING REMOVAL PROCESS. SNAPPING OF THE CLIPS CAN CAUSE INJURIES TO THE HAND.
DO NOT USE ANY OTHER DRIVER EXCEPT PARMIDA LIGHTING DRIVER THAT IS INCLUDED WITH THE FIXTURE.

info@parmida.com
www.parmida.com