ONFORU MZT-FW01 Smart LED Light Instruction Manual

: June 5, 2024
: ONFORU

Table of Contents

SAFETY INFORMATION
PARAMETER
COMPONENTS
CONNECTION DIAGRAM
PAIRING LED LIGHT WITH”Onforu” App.
AMAZON ALEXA
GOOGLE ASSISTANT APP
INSTALLATION STEPS
GENERAL MATTERS FOR ATTENTION
Documents / Resources

MZT-FW01 Smart LED Light
Instruction Manual

SAFETY INFORMATION

Disconnect the power supply before attempting any work on the unit！

This product is not a toy. Do not let children play with it as a toy.
Check all components for damage, do not use the product if it is damaged.
To ensure the product can work normally, please use it in the voltage within the range on the lamp label.
This product is not waterproof, please do not submerge it in water or do not use it in a humid environment for a long time.
Do not install the unit on (normally) flammable surfaces.
To reduce the risk of strangulation the flexible wiring connected to this luminaire shall be effectively fixed to the wall if the wiring is within arm’s reach
The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
Never plug the light in with wet hands in case of electric shock.
The housing of the light is made of plastic, do not wipe it with strong detergents and other chemical cleaners when cleaning.
Please use our power adapter and other accessories in the package. For other power adapters, the light may not work or be damaged.
Risk of fire–Do not replace the power plug. This plug contains a safety device (fuse) that must not be removed, if the power plug is damaged, please discard this product.

PARAMETER

| 253x38x43 mm 9.96×1.50×1.69 in
---|---
| 0.83 kg / 1.83 lb
| 100-120V ～60Hz / 220-240V ～50Hz
| RGB/2700-6500K
| Wi-Fi
PF| >0.5
| -25°C － 40°C / -4°F －104°F

COMPONENTS

Smart LED Light
Screws
Plastic Expansion Nails
Angular support
Hanging buckle
3M adhesive
Base
Adapter
Controller

CONNECTION DIAGRAM

Connect the LED light to the Controller, and then to the power adapter. Plug in the power cord and press the power cord switch to turn on / off the LED light.

PAIRING LED LIGHT WITH”Onforu” App.

NOTE:
Turn ON/OFF the Smart LED Light three times until the LED Light starts to flash quickly, which indicates the success of the factory reset.
Step 1: “Onforu Home” App Download. There are 2 options for obtaining and downloading the “Onforu Home” App on your smart device.

Scan the QR code on the right.
Search for “Onforu Home” in the App Store or Google Play.

****https://a.smart321.com/wwwyouliang

Step 2: Enter the “Onforu Home” App. and register an account and log in. If you already have an account for Onforu Home App., Please select “Log in with existing account”.
Note: You will need your “Onforu Home” App. username and password to pair with Amazon Alexa and/or Google Assistant.

Step 3. Please turn on the Wi-Fi and Bluetooth before connecting LED lights to the “Onforu Home” APP. Tap the “+” button on the top right corner to add a device, then tap”lighting device” to enter the next page.
Note: This smart LED Light can only support a 2.4 GHz network and cannot work with a 5.0 GHz network. Please check if your home network is 2.4 GHz and make sure that your phone has been connected to your Wi-Fi network. Please ensure your network is not hidden.

Step 4. How to pair the LED Light.

Power on the LED Light.
Power off it three times quickly until the LED chips flashes, it indicates that the flood
light has entered pairing mode.
Tap the confirmation button to pair the LED Light.
Enter your Wi-Fi password to join your network.
Please Note:
a. This smart LED Light can only support a 2.4 GHz network and cannot work with a 5.0 GHz network.
b. Please check if your home network is 2.4 GHz and make sure that your phone has been connected to your Wi-Fi network. Please ensure your network is not hidden.
Wait till it is successfully connected.

Note: If the LED Light is still flashing until the progress map reaches 100%, the pairing fails, and you will need to repeat the previous 4 steps to pair the LED Light.

Step 5. Name the LED light and tap “Done”. You will find the device you’ve named is shown on the App homepage. Tap the device to enter the setting page. You can now control the light with Onforu Home App. on this setting page.

AMAZON ALEXA

Please make sure that your Alexa App. is connected to Amazon Echo, and that both work together successfully under your Wi-Fi network.
Step A : Log in your Alexa App., tap at the top left corner, and tap “Skills”. Bitte stellen Sie sicher, dass Ihre Alexa

Step B: Type “Onforu Home” to search for “Onforu Home”, and enable “Onforu Home” on Alexa.

Step C: Enter your account and password of Onforu Home App., tap “Nest Step”, then tap ” Authorize” on the next page to authorize Onforu Home Info to Alexa. Note: Same account and password as Onforu Home App.

Step D: Once your Onforu Home account is successfully connected to Alexa, the following page will pop up. Tap “CLOSE” , then tap “DISCOVER DEVICES” on the next page.
Schritt D : Sobald Ihr Onforu Home Konto

Step E: Wait a few seconds for Alexa to detect the LED Light from Onforu Home App., and you will find the device named “Smart LED Light” has been paired to Alexa App from Onforu Home pp. after step E is done, you can now control the light with Alexa App. on this setting page.
A. slide to change brightness
B. tap to turn on/off the light
C. enter to change colors

Try these commands and see what happens by asking Alexa :
Alexa, turn on “device name”
Alexa, turn off “device name”
Alexa, set “device name” to “color”
Alexa, set “device name” to “number”
For example: “Alexa, turn on Smart LED Light”, “Alexa, dim Smart LED Light to 50%” etc.
Note: The device name is the one you give to the LED Light on Onforu Home App. In this user guide, the device is named “Smart LED Light”.

GOOGLE ASSISTANT APP

Step A: Open your Google Home App., and tap “Home Control” on the Left Side Bar page.
Step B: Tap the “+” button on the bottom right corner to enter the next page.

Step C : Find “Onforu Home from the sidebar list.

Step D: Enter your account and password of Onforu Home App., tap “Link Now”, then tap “Authorize” on the next page to authorize your Onforu Home Account Info to Google Home .
Note: Same account and password as Onforu Home App.

Step E: You will find that Google Home has found the device named “Smart LED Light” on this page.

Try these commands and see what happens by asking Google :
ok, Google, turn on “device name”
ok, Google, turn off “device name”
ok, Google, set the “device name” to “color”
ok, Google, set “device name” to “number”
For example: “ok Google, turn on Smart LED Light”, “ok Google, dim Smart LED Light To 50%” etc.
Note: The device name is the one you give to the LED Light on Onforu Home App. In this user guide, the device is named “Smart LED Light”.

INSTALLATION STEPS

There are four methods to fix the LED light:
The First Method: Pass the connecting wire through the base and snap the wire into the two buckles of the base, then insert the LED light into the base. (As shown in the picture on the right)

The Second Method: Place the LED light on the angular support. (Four types of placement angles, as shown in the picture below)
The Third Method: Fasten the hanging buckle to the wall with screws, then insert the LED light into the hanging buckle; (Two methods of fixing, vertical and horizontal, as shown in the picture below).
The Fourth Method: Paste the 3M adhesive on the back of the light, then peel off the 3M adhesive and stick it on the wall; (Two angles: vertical or horizontal, as shown below)
Note: The wall must remain clean and flat, free of dust, oil stains, water, and other objects affecting the stickiness of 3M, otherwise the LED light would not stick.

GENERAL MATTERS FOR ATTENTION

This smart LED Light can only support a 2.4 GHz network and cannot work with a 5.0 GHz network. Please check if your home network is 2.4 GHz and make sure that your phone has been connected to your Wi-Fi network. Please ensure your network is not hidden.
If you fail to connect the LED Light with your Wi-Fi, please check whether your network is stable and fast. Slow networking speed may result in failure of connection.
If you fail to connect the LED Light with your Wi-Fi, please ensure your Wi-Fi password is correct. If not, please re-enter the correct password.
Wi-Fi Connection Issues If a router/Wi-Fi password changes or additional smart devices register with the “Onforu Home” App., a factory reset of the Smart LED Light is required.
If any matters regarding the Smart LED Light connection to happen, you can reset the factory setting of LED Light, then re-connect the Smart LED Light.

Note
01 Safety Class Ill = Only operate lamps with this symbol with Safety Extra Low Voltage (SELV). Only connect to SELV circuits.
Operation / Maintenance
Never use any chemicals or corrosive substances for cleaning.
Disposal
Electrical and electronic equipment, accessories, and packaging must be recycled in an environmentally compatible manner. Do not dispose of electrical and electronic equipment as domestic waste.
EU countries only:
Under the current European Directive on Waste Electrical and Electronic equipment and its implementation in national law, electrical and electronic equipment no longer suitable for use must be collected separately and recycled in an environmentally compatible manner.

Manufacturer / Hersteller:
Shen Zhen Shi Meng Zhi Tuo Ke Ji You Xian Gong Si
Address: Qian wan yi lu 1 hao A dong 201 shi Qian hai shen gang he Zuo Qu Shen Zhen, Guang
Dong, 518000, CN
support@onforuled.com
www.onforuleds.com
EU REP MDH LIGHTING LTD
Suite 302, 292 Strovolos Avenue, 2048 Strovolos
Nicosia, Cyprus
support@onforuled.com
UK REP MDH LIGHTING LTD
69 Aberdeen Avenue, Cambridge CB2 8DL,
United Kingdom
support@onforuled.com
Made in China