Kruger Matz KM2005.2 Car Receiver Owner’s Manual

Kruger Matz KM2005.2 Car Receiver

SAFETY INSTRUCTIONS

Installation precautions

• This unit is designed to operate on a 10,8-16 V DC power supply. If your vehicle does not have this system, a voltage inverter is required. The device also requires connecting to the negative of the car.

• Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Install the unit where it does not get in the driver‘s way and cannot injure the passenger if there is a sudden stop. DO NOT install the unit or any cable in a location where:

  • it may obstruct the steering wheel and gearshift lever operations,
  • it may obstruct the operation of safety devices such as airbags
  • it may obstruct visibility
  • there is not enough ventilation provided

• Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, hot air, or a heater, or where it would be subject to dust, dirt or excessive vibration.

• Do not expose this equipment to rain or moisture nor use it near strong magnetic fields. Do not handle this appliance with wet hands.

• Make sure all the connections are executed in a proper manner. The reversed connection will cause a short circuit and damage.

• If the installation angle exceeds 30 from the horizontal, the unit might not give its optimum performance.

• Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.

• If the fuse blows, check the power connection and replace the fuse with one of the same specified ratings. If the fuse blows frequently, consult an authorized service point for a check-up/ repair.

• It is recommended to connect speakers with an impedance of 4 Ω.

• To prevent short circuits, cover the terminals of the UNUSED leads with insulating tape.

• Make sure that the ignition is off before connecting the device.

• Make sure to connect the yellow and red power supply cables after all other cables are already connected.

• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

• At the time of installation, be sure to fix all wires (wires both from this unit and from the car itself) in a way that any wires cannot come into contact with heat sinks on the rear and side of the unit.

• Installation illustrations show a typical installation. However, you should make adjustments corresponding to your specific car. If you have any questions or require information regarding installation kits, consult your car dealer.

• If you are not sure how to install this unit correctly, have it installed by a qualified technician. The producer does not claim liability for incorrect mounting/installation nor for inappropriate handling and uses disregarding this user’s manual.

• When mounting the unit, be sure to use the screws provided, as instructed. If other screws are used, parts could become loose or damaged. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.

• When tightening screws or bolts, be careful not to pinch any connection cord.

• Make sure not to block the ventilation outlets.

• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged.

• BEFORE connecting the speaker leads, check the speaker wiring in your car.

• Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. In case of any doubts concerning the place of installation, contact your vehicle’s dealer. Before drilling the holes in the vehicle’s body, make sure it will not damage any electrical cables or other components. During installation keep in mind, that any loose parts may pose danger in case of an accident – make sure to install every piece properly to ensure safety.

• • Do not remove the housing/disassemble the device. The device has no user-serviceable parts
  inside.

• In case of damage, contact an authorized service point for a check-up/repair.

Temperature

• If the vehicle has been parked for a long time in hot or cold environment, wait until the temperature in the vehicle becomes normal before operating the unit.
• When installing, to ensure proper heat dispersal when using this unit, make sure to leave some space behind the rear panel and wrap any loose cables so they are not blocking the ventilation outlets.

Safety instructions

• DO NOT operate this device while driving, as this may lead to a traffic accident.
• The driver must not watch the monitor while driving.
• Stop the car before performing any operations! Do not perform any activities that may distract from cautious driving, such as managing a playlist.
• Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.
• Clean with soft, slightly damp cloth only.
• When inserting batteries, please note the correct polarity.
• If the remote is not used for an extended period of time, remove the battery to prevent possible damage from battery leakage.

Hearing safety

• Listen at a moderate volume. Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes of sound. So after prolonged listening, what sounds “normal” can actually be loud and harmful to your hearing. To guard against this, set your volume to a safe level before your hearing adapts and leave it there.
• Listen for reasonable periods of time:
  • Prolonged exposure to sound, even at normally “safe” levels, can also cause hearing loss.
  • Be sure to use your equipment reasonably and take appropriate breaks.

Notes on external memory

• Use the memory drive only as indicated in its user’s manual
• Do not touch the USB port/plug with a bare hand; do not touch metal objects.
• Do not expose the memory drive to shocks.
• Do not bend, drop, disassemble, or modify the memory drive. Protect from water and humidity.
• Do not store memory drive inside the vehicle where it will be exposed to direct sunlight, high temperatures, high humidity or corrosive substances.
• Make sure the connected USB drive does not obstruct unhindered vehicle driving.
• The memory drive may not function properly in extremely high/low-temperature environments.
• Use only authorized memory drives. Please note, that the producer does not guarantee compatibility with every external memory.
• Files protected against copying (copyright protection) may not be played.
• In some cases, the start of the playback may be delayed but does not constitute any malfunction or damage.
• The producer does not claim any liability for any data loss.
• Do not unplug external memory while playback. Change the sound source before disconnecting the memory drive from this device.

Description of front panel buttons

1. Release button
2. Knob / Left and right adjustment button / Answer/redial the last number in Bluetooth mode / Press and hold to adjust panel tilt angle downwards / upwards
3. Number key 1 / play and pause
4. Number key 3 / random play
5. Number key 5 / adjust the angle of the display screen upwards.
6. IR sensor
7. LCD window
8. Mute / hang up for Bluetooth mode
9. AUX input
10. USB port
11. MIC (Bluetooth option only)
12. Number key 6 / adjust the angle of the display screen downwards.
13. Number key 4 / ready-to-be-stop
14. Number key 2 / repeated play
15. Prev
16. Power off (long press) / Press any button to start the unit and in or out of the telescopic screen (short press)
17. Under the radio mode, AM / FM band switch
18. Press to change mode
19. Next
20. Reset
21. SD/MMC card slot

Wiring diagram

Operation

The operation of the main menu on the device’s display is based on the touch function. Touch/slide to perform desired actions. Here are some basic movements in the general operation of the radio:

• Press to return to the main menu.
• Touch one of the mode icons on the main menu vertical slide bar to enter directly. Press the mode icon in the circle at the left to enter the mode directly.
• Press to return to the previous screen.
• Press to adjust the panel tilt angle downwards.
• Press to adjust the panel tilt angle upwards.
• Press to change the background picture.
• Press to change brightness adjustments:
  • Daytime mode
  • Nightfall mode
  • Night mode
  • User mode (press the to adjust brightness level – all modes will change accordingly)
  • Screen close mode (the screen will be off, press any button to restore to daytime mode)
• Press to enter screen close mode directly
• Press to enter the setting window (once in the menu, rotate the knob on the front panel to change adjustments; press the knob to confirm and go to another setting. In case of not operation within 5 seconds, the window will disappear)
• Press the clock on the main screen to change between analog/digital clock.

Radio Menu

1. Enter radio mode.
2. Conduct band switching by touching the FM1 icon on the radio menu: FM1→FM2→FM3→AM1→AM2.
3. Press the icon on the radio menu to browse the pre-set frequency of the radio.
4. Drag the radio frequency pointer to set desired frequency.
5. Press the icon to start an automatic decrease stations search. Press and hold the or press icon to go 0,05 MHz down.
6. Press the icon to start automatic increase stations search. Press and hold the or press icon to go 0,05 MHz up.
7. Press to search and store stations automatically (press again to stop scanning and play the current channel).
8. Turn on/off stereo by touching icon on the radio menu.
9. Press the to turn on/off local function.
10. Press PTY to select program type
11. Press TA to turn on/off trafic anouncement function
12. Press AF for frequency replacement table switching
13. Touch the pre-set frequency unit cell on the radio menu to listen to the radio frequency stored in the cell.
14. Press and hold down the pre-set frequency unit cell for three seconds on the radio menu to store the frequency played currently.

USB/SD basic buttons description

Note: slide the toolbar at the bottom to the left/right to show the next options. Press one of the icons to perform desired action/enter/enable:

• menu list – enter to display:
  • song list menu
  • image list menu
  • video list menu
  • folder list menu
• Press to go to previous song/press and hold to fast reverse
• play/pause
• press to go to the next song/press and hold to fast forward
• change playback mode (repeat one / repeat folder/repeat all)
• random playback
• change stereo settings (mono right / mono left / stereo)
• stop

Bluetooth
Prior to use via Bluetooth, pair the radio with an external Bluetooth device. To pair the radio with an external device:

1. Enter Bluetooth mode from the main screen.
2. Enable Bluetooth function on your external device. Remember to enable its visibility.
3. Conduct pairing on the external device. Input default password if necessary: 0000.

Once connected, press one of the icons to perform desired action/enter/enable

• Dial interface (during the call, the user can mute the microphone and switch between radio and phone)

• Calls records

• Phonebook (by default, the phonebook is not loaded into the radio. Press to load the contacts. Please note, that the phone may ask you to confirm whether to allow the radio to see contacts. Press to open the keypad to search for a record.)

• BT music (press to enter the audio streaming interface. Please note, that you have to start the music playback from the external device first to manage the playback.)

• BT connection settings.

Setting interface

Enter the Setup tab to manage your device. Touch one of the icons on the bottom tab to enter:

System settings

• Area (select appropriate)
• Language (select appropriate)
• Rear camera (on/off)
• Headlamp detection (on/off)
• Brake detection (on/off)
• Subwoofer (on/off)
• Beep (on/off)

Audio settings

• EQ (select appropriate)
• Field (adjust appropriately)
• Loudness (on/off)

Display settings

• Type (select appropriate)
• Adjust (adjust appropriately)

Media settings

• Aspect ratio (select appropriate)

BT settings

• BT (on/off)
• Name (change accordingly)
• PIN code (change accordingly. default password is „0000”)
• Auto link (automatic connection on/off; note: when the function is ON, the radio will automatically connect with the external device when within operational range, and both have BT function on)
• Auto answer (automatic incoming call answering on/off)
• Auto loading records (on/off)
• Auto loading phonebooks (on/off)
• Call volume (on/off)

Time

• Display mode (select appropriate date format)
• Display format (select appropriate time format)
• Adjust (input date and time)

Light

• Backlight adjust (adjust appropriately)
• Color light (select appropriate)
• Auto cycle time (select appropriate)

SWC (steering wheel control)

• Steering wheel (on/off)
• Study (enter to program steering wheel control function)

Touch

• Touch for calibration (touch to perform display calibration)

NOTE:  Factory reset password: 123456

Steering wheel setting menu

• Enter “Setup” on the main menu and then the “SWC” and “Study” tab for the steering wheel control learning menu.
• To program the buttons:

1. Press and hold the function button of the steering wheel, and then press and hold the selected function key icon on the steering wheel setting interface.
2. After the learning is successful, the learning box will be lightened, which indicates successful learning.
3. Set subsequent buttons to be set as described until the setting is completed.
4. After successful learning, click the icon to save the learning result automatically.
5. To reprogram the buttons or remove the mistaken learning, click the icon. The system will cancel the learning function of all keys.

Wiring operation for steering wheel control

Single wiring for steering wheel control: connect KEY1 (brown) and KEYGND (black) in the wire bundle of the power cord of the system with KEY1 (brown) and KEYGND (black) in the steering wheel of cars. The schematic diagram is as the following:

Double wiring for steering wheel control: connect KEY1 (brown) KEY2 (brownish black), KEYGND (black) in the wire bundle of the power cord with KEY1 (brown), KEY2 (brownish black), and KEYGND (black) in the steering wheel of cars. The schematic diagram is as the following:

Wallpaper picture change

• Press on the main menu to change the background picture.

PHONE LINK

Note

• the app is compatible with mobile devices running Android 5.0 (and higher). It’s not compatible with iOS devices.
• USB debugging of your mobile device shall be turned on.

1. Download and install the Vehicle multimedia entertainment APP Autolink from Google Play Store.
   • Enter “Phone link” on the main menu of the radio receiver to scan the QR code, or go directly to the Google Play Store on your mobile phone to download the app.
   • Note: If the installation has failed, check whether security apps on your mobile device have stopped the installation.
2. Connect your mobile device to the radio receiver via a USB cable. A notification will show on your mobile device: “Open Autolink when this USB accessory is connected?” Please click “OK”. Users can also enable the default usage here.
3. On your mobile device screen, a note may appear about capturing everything that is displayed on your screen. Approve to proceed.
4. The radio receiver screen will display what’s on your mobile phone’s screen.

Description of Phone Link Menu

1. When the Phone Link has been connected successfully, you’ll see . Press it and you’ll see the menu. You can close the Phone Link menu by clicking the areas outside the menu.

2. Exit the Phone Link and return to the main menu.

3. Back

4. Turn on or off the screen display.

5. Go to main screen of your phone.

6. Allow screen rotation (screen rotation on your phone must be enabled first).

7. Adjust volume and mute.

Remote control operation

1. (Power switch) button: press this button to switch on or off the power supply.
2. (Mode conversion) button: press this button to switch the different modes in a cycle.
3. (Play/pause) button: under the sound playing state, press this button to switch between playing and pause; under the pause state, press this button to play.
4. (Mute) button: press this button to close the volume output. Press it again to restore the former volume level.
5. AMS button: in radio mode, press to do the preset scan/press and hold to perform radio station searching and store automatically into those preset numbers.
6. MUSIC button: in USB/SD mode, press to enter the menu of the MP3 directory.
7. MOVIE button: in USB/SD mode, press to enter the menu of the movie directory.
8. Local button: in radio mode, press to switch between Local and Distance radio stations.
9. PHOTO button: in USB/SD mode, press to enter the menu of the picture directory.
10. Volume Up / Down buttons: adjust the volume up/down.
11. Zoom button: zoom in on images
12. Select/Answer button: multi-function button to set Volume / Treble / Base / Balance / Fader; press to answer/redial last number the call in BT mode
13. Seek Up / Down buttons ( ):
    • in radio mode, press to auto searches the radio station up or down respectively. Press and hold one of these buttons for a manual search of radio stations.
    • in audio and video playback mode, press and hold to fast forward or backward respectively. Briefly press one of these buttons to change to the next/previous track.
14. Backspace button
15. Loudness button
16. EQ button/press to reject/end call in BT mode
17. Numeric keyboard buttons
18. button
19. Audio button: in video mode, it can select different language audio tracks of the video
20. RDM button: in USB / SD mode, randomly plays video track
21. REPEAT button: in USB / SD mode, repeats video track playback
22. ST button: in tuner mode, switches between audio with stereo and mono channel
23. Return button
24. Enter button: confirm the selection of menu options
25. Left / Right buttons: browse the menu left and right
26. Band button:
    • in radio mode, switch between the AM and FM bands
27. Up / Down buttons: browse the menu up and down
28. AF button: frequency replacement table switching
29. PTY button: program type selection
30. TA button: traffic announcement switching

REPLACING THE REMOTE BATTERY

Replace the CR2025 battery in the remote control with a new one whenever its operational range is shortened or the device does not respond to the remote.

Please note: before the first operation removes the insulation strip from the battery compartment.

1. Retrieve battery compartment.
2. Insert the CR2025 battery into the battery compartment. Put the battery with a (+) mark upward (when the remote is with buttons facing downward). Pay attention to the correct polarity.
3. Insert the battery compartment back into the remote.

SPECIFICATION

Technical parameters

• Max. power: 4 x 40 W
• RMS power: 4 x 25 W
• S/N ratio: >55 dB
• Channel separation: >55 dB
• Frequency response: 16 Hz-25 kHz
• Power supply: 10,8-16 V DC
• Load impedance: 4 Ω
• Fuse: <10 A

Display

• Size: 7”
• Panel: TFT
• Resolution: 800×480 px
• Touchscreen: Resistive
• Display brightness: Adjustable
• Panel tilt angle: Adjustable

Main features

• Size: 1 DIN
• Supported formats
• Audio: MP3, AAC, WMA, FLAC, WAV
• Video: MP4, DIVX, AVI, RMVB, MKV
• Picture: JPG, PNG, GIF
• Panel: detachable
• Equalizer: Pop/Rock/Classic/Flat/Jazz/Electro/User
• Operating system: WIN CE 6.0
• RAM: 64 MB
• Supported standard: PAL/NTSC
• Steering wheel control: Yes (analog)
• Tone controls:
• Bass (at 100 Hz): ± 7 dB
• Treble (at 100 kHz): ± 7 dB
• Keys backlight: RGB
• Microphone: Yes
• App compatibility: Android 5.0 and later

Bluetooth

• Version: 2.1
• Phone call management: Yes
• Phonebook synchronization: Yes
• Audio streaming: Yes

Analog radio tuner

• FM frequency range: 87,5 – 108 MHz
• AM frequency range: 522 – 1620 kHz
• FM preset memory: 18
• AM preset memory: 12
• RDS: Yes (AF/TP/TA/EON/PTY)
• Frequency search: automatic/manual
• Stereo separation: >40 dB

I/O

• USB port: 2.1 (max. capacity: 32 GB)
• Memory card reader: microSD (player; max. capacity: 32 GB)
• AUX socket: Jack 3,5 mm
• RCA output: 4x RCA low impedance line output at 1,2 V
• Subwoofer line output: x2
• Rearview camera input: Yes
• Video output: x2
• Video input: Yes
• Audio input: 2x RCA

Environmental

• Operating temperature: -20~60°C
• Storage temperature: -20~70°C

IMPORTANT: The producer allows the possibility for minor variations in display brightness and color between individual devices. There may be visible light or dark spots on the display. Up to 5 defective pixels are acceptable to be present on the display of the device. Above mentioned cases concerning the device’s display are not covered under warranty nor statutory warranty rights.

Producer reserves rights to change product overview and specifications without prior notice.

Please note: illustrations and descriptions concerning the operating systems are for reference only, and may vary from actual software on your device! Any information included in this manual is subject to change without prior notice.

Lechpol Electronics Sp. z o.o. Sp.k. hereby declares that car receiver KM2005.2 is consistent with directive 2014/53/UE. The full text of the EU Declaration of Conformity is available at the following Internet address: www.lechpol.eu.

Correct Disposal of This Product (Waste Electrical & Electronic

Equipment)

(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature indicates that it should not be disposed of with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of waste and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their suppliers and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

Made in China for LECHPOL ELECTRONICS Sp. z o.o. Sp.k., ul. Garwolińska 1, 08-400 Miętne.

www.krugermatz.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>