Schreder Ecoblast 3 LED Solution for Sports Lightning Instruction Manual

June 4, 2024
Schreder

Eco blast 3 LED Solution for Sports Lightning
Instruction Manual

INSTALLATION INSTRUCTIONS

Schreder Ecoblast 3 LED Solution for Sports Lightning - fig
1

PRODUCT OVERVIEW

Schreder Ecoblast 3 LED Solution for Sports Lightning -
fig 2

***** Weights correspond to remote driver installation, with QPD connector for ECO BLAST 3-4, with Junction box for ECO BLAST 5-6. Attached driver means an additional 7.1kg (15.7 lbs) for ECO BLAST 3-4, an additional 7.5kg (16.5 lbs) for ECO BLAST 5-6 (including driver holder plates). Tolerance on weight values is +/-5%.

GEARBLAST – DRIVER OVERVIEW

Schreder Ecoblast 3 LED Solution for Sports Lightning - fig
3

LAYOUT AND MOUNTING

**ECOBLAST 3

ECOBLAST 4-5-6
SAFETY CABLE
**

  • For installations over 3 meters in height:
    the secondary safety system application is mandatory, which is appropriated for the luminaire load (for example steel safety cable)

  • 600mm safety cable can be optionally ordered with the luminaire

Minimum screw requirement:

Vibration standard IEC 0.5g / ANSI 1.5g ANSI 3g
Minimum fastener requirement 1x M20 8.8 or A2-70
DIN9021 large plain washer 1x M20 8.8 or A2-70 + 1x M10 8.8 or A2-70 DIN125

plain  washers
Tightening torques| M20: 150-175 Nm| M20: 150-175 Nm
M10: 35-40 Nm

Recommended using an anti-seizing agent (Tikal Tef-Gel®)!
Schreder Ecoblast 3 LED Solution for Sports Lightning - fig
51 Fasteners not included in the package!
The relevant CSS and weight values can be found in this document.

DRIVER CONNECTION-DRIVER MOUNTED ON FORK

Schreder Ecoblast 3 LED Solution for Sports Lightning - fig
5

**** AC and CONTROL cables must be connected by the installer

|
---|---
REMOVE SCREWS| CONNECT THE AC, CONTROL, AND LED MODULE WIRES
MAKE THE ELECTRICAL CONNECTION
blade dimensions: 3.5 x 0.5 mm
**** Use appropriate tools for electrical connections!| TIGHTEN THE DRIVER COVER

MAINS CONNECTION

**CLAMPING RANGE: 10-17MM

In case of using a smaller outer diameter cable, please replace the cable gland’s internal gasket with the one attached in the packaging.
Modified clamping range: 7-13 mm
Schreder Ecoblast 3 LED Solution for Sports Lightning - fig
13**

DALI

2X M16 CABLE GLAND
CLAMPING RANGE: 5-10MM
Schreder Ecoblast 3 LED Solution for Sports Lightning - fig
15

DMX

2X M16 CABLE GLAND
CLAMPING RANGE: 5-10MM
Schreder Ecoblast 3 LED Solution for Sports Lightning - fig
17

OPTICAL BLOCK

M32 CABLE GLAND
CLAMPING RANGE: 13-21MM
In case of using a smaller outer diameter cable, please replace the cable gland’s internal gasket with the one attached in the packaging.
Modified clamping range: 8-14 mm
2 channels

CONNECTOR ID CABLE ID EU CABLE ID US
GND Yellow/Green Green
+1 1  /  Brown 1   /   Pink
-1 2  /    Blue   2   /   White
+3 3  /  Black  3  /  Black
-3 4  /    Grey   4  /White-Black


CONNECTOR ID CABLE ID EU CABLE ID US
GND Yellow/Green Green
+1 1 1     /  Pink
-1 2  2    /  White
+2 3  3    /  Black
-2 4 4  /  White-Black
+3 5 5  /  Blue
-3 6  6  / Orange

DRIVER CONNECTION – REMOTE DRIVER INSTALLATION

L<100m WIRE SIZE 1,5mm2
100<L<200m WIRE SIZE 2,5mm2
MAX REMOTE DISTANCE 200M!| 3 + 4 MODULE TYPES
AVAILABLE WITH QPD CONNECTOR| 5 + 6 MODULE TYPES
AVAILABLE WITH JUNCTION BOX
---|---|---
QPD CONNECTOR
TYPE (5-CORE WIRE)
THE INTERCONNECTION CABLE IS NOT INCLUDED IN THE PACKAGE!
Schreder Ecoblast 3 LED Solution for Sports Lightning - fig
24| JUNCTION BOX
TYPE (7-CORE WIRE)
THE INTERCONNECTION CABLE IS NOT INCLUDED IN THE PACKAGE!
Schreder Ecoblast 3 LED Solution for Sports Lightning - fig
25
---|---

DRIVER CONNECTION ACCORDING TO PAGES 3-4-5
1a
Schreder Ecoblast 3 LED Solution for Sports Lightning - fig
26

DRIVER TERMINAL QPD ID
GND
1 1
-1 2
3 3
-3 4

CLAMPING RANGE:
Ø9-16mm 5G1.5mm2 – 5G2.5mm2

Schreder Ecoblast 3 LED Solution for Sports Lightning - fig
28
Remove screws from the junction box cover
Schreder Ecoblast 3 LED Solution for Sports Lightning - fig
29
Connect the junction box to the junction box support plate
Schreder Ecoblast 3 LED Solution for Sports Lightning - fig
30
Make the electrical connection with WAGO terminal blocks
Schreder Ecoblast 3 LED Solution for Sports Lightning - fig
31
Tighten the junction box cover

ANGLE ADJUSTMENT

**ECOBLAST 3

ALLOWED tilt angle is between -10° to 70°
STEPS
**

  1. Loosen the clamp screws (4xM8)
  2. Adjust the tilting angle
  3. Tighten the clamp screws with 13Nm

ANGLE LIMITATIONS

****|
---|---
Direct installation| Suspended installation

ECOBLAST 4-5-6
The swing arm inclination is adjustable in 5-degree increments relative to fork baseSchreder Ecoblast 3 LED Solution for Sports Lightning - fig
53

Separate scale sheet for adjusting optical block angles relative to the swing arm The inclination angle of the swing arm and the optical blocks can be adjusted separately
ALLOWED tilt angle is between -10° to 70°

OFFSET LAYOUT INSTALLATION

REASSEMBLY STEPS

Lay the complete luminaire with all optical block front faces touching the ground|
---|---
Loosen the screws of the 2 main clamps and the 2 set screws of the brackets|
Remove the shaft by rotating and pulling it in one direction|
Remove the 2 main clamps, 4 screws, nuts, washers, and anti-rotation clips from the initial position|
Remove the 2 main clamps, 4 screws, nuts, washers, and anti-rotation clips from the initial position|
Align the fork to the brackets with the 2nd position hole|
Insert and rotate the shaft until the flat surface is toward the set screws in the brackets|
| Schreder Ecoblast 3 LED Solution for Sports Lightning - fig
44

OFFSET LAYOUT LIMITATIONS

In the case of the standard mounting option, the angle of inclination can only be between 60° and 70° without any collision

INRUSH DATA AND LUMINAIRES PER CIRCUIT BREAKER

The maximum number of LED drivers connectable to a single MCB is reported in the following table for each nominal input voltage. a maximum number of LED drivers connectable to a single MCB is reported in the following table for each nominal input voltage. Due to the different kinds of circuit breakers available on the market, this table just for reference.  to the different kinds of circuit breakers available on the market, this table is just for reference.
1200 W

VIN| Inrush Current Data| | | | | | Drivers For Each Circuit Breaker| | | |
---|---|---|---|---|---|---|---|---|---|---|---
Nominal
[VAC]| I peak
[A]| Half Value Time [its]| | | Type B| | | | | Type C| | | | | Type D| |
10A| 16A| 20A| 25A| 32A| 10A| 16A| 20A| 25A| 32A| 10A| 16A| 20A| 25A| 32A
220/240| 26| 6400| 1| 2| 2| 3| 4| 1| 2| 2| 3| 4| 1| 2| 2| 3| 4
400| 14| 4700| 2| 3| 4| 5| 6| 2| 3| 4| 5| 6| 2| 3| 4| 5| 6

1800 W

VIN| Inrush Current Data| | | | | | Drivers For Each Circuit Breaker| | | |
---|---|---|---|---|---|---|---|---|---|---|---
Nominal
[VAC]| I peak [A]| Half Value
Time [µs]| | | Type B| | | | | Type C| | | | | Type D| |
10A| 16A| 20A| 25A| 32A| 10A| 16A| 20A| 25A| 32A| 10A| 16A| 20A| 25A| 32A
220/240| 26| 6400| 1| 1| 2| 2| 3| 1| 1| 2| 2| 3| 1| 1| 2| 2| 3
400| 20| 1500| 1| 2| 2| 3| 4| 1| 2| 2| 3| 4| 1| 2| 2| 3| 4

SAFETY INSTRUCTIONS
The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similarly qualified person. Always switch off the power prior to installation, maintenance, or repair activities.
RISK GROUP 2 – CAUTION! Hazardous optical radiation may be emitted from this product. Do not stare at the luminaire when operating as it may be harmful to the eyes. The luminaire should be positioned so that prolonged staring at the luminaire at a distance of fewer than 0.2m is not expected. This product contains a light source of an energy efficiency class G or higher. In the case of PVC  insulated mains cable, the installer MUST ensure that the WHOLE cable is protected against climatic conditions, especially UV rays and rain, by making sure that the cable is contained inside the luminaire and pole
Y-connection: In case of damage to the wire, it has to be replaced only by the manufacturer, distributor, or an expert, to avoid risks.

01-85-943 | DOC-0018707 rev J | 12-2021
www.schreder.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Schreder User Manuals

Related Manuals