eurotops H1123S Croix KNIFE SHARPENER User Manual

eurotops H1123S Croix KNIFE SHARPENER User Manual

KNIFE SHARPENER

Warning: Please read this instruction manual carefully before using the instrument and keep it for future use.

SAFETY INSTRUCTIONS

• Always pull the knife toward you. Never push the knife away from you.
• Do not twist the knife when sharpening.
• Keep constant force and speed during sharpening.
• Cleaning by dishwasher is forbidden, the exterior of sharpener should be cleaned up by a soft cloth, don’t immerse the sharpener into water or other liquid.
• The device is intended exclusively for private and not for commercial use. Only use this device as describe in this instruction manual.
• Always place your device on a dry surface.
• Keep it away from heat sources such as radiators, to avoid deformation of plastic parts.
• Do not use coarse or abrasive sponges/cloths or steel wool to clean the appliance.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capacities, or by persons lacking in experience or knowledge, unless they are supervised or instructed on the use of this apparatus by a person responsible for their safety.Children should be supervised to ensure they do not play with this appliance.

HOW TO USE IT

This device is designed to sharpen kitchen knives, pocket knives or other metal or ceramic knives. Do not use razor blades or any other blade that are not suitable in size and / or thickness to the knife sharpener.

Always use this device after cleaning blades (see section “care and maintenance”).

Place the knife sharpener on a flat, stable surface.
Hold the sharpener with one hand and the knife handle with the other.

Slot 1 Diamond Coated Rods (Preparation)

Repair damaged edges and balance the blade before actually sharpening.
Insert knife blade fully into the slot at a 90°angle to the sharpener. Apply light downward pressure on the blade while pulling the knife through the sharpening slot from heel to tip. Avoid rubbing the face of the blade against the walls of the slot when sharpening. Always pull the knife from heal to tip, never push the knife away from you.

Repeat this action, normally 5-7 pulls will get the blade sharp, but knives made of extremely hard steel may require additional pulls.
**For ceramic knives this step is sufficient.

**

Slot 2 Carbide Blades (Sharpening)

Sharpen the blade and restore its shape to a V- cut.
Insert knife blade fully into the slot at a 90°angle to the sharpener. Apply light downward pressure on the blade while pulling the knife through the sharpening slot from heel to tip. Avoid rubbing the face of the blade against the walls of the slot when sharpening. Always pull the knife from heal to tip, never push the knife away from you.

Repeat this action, normally 5-7 pulls will get the blade sharp, but knives made of extremely hard steel may require additional pulls.
**Never use on a ceramic blade! This could irreversibly damage or break it!

**

Slot 3 Ceramic Rods (Polishing)

Remove burrs and polish the blade so that it is as sharp as razor.
The polishing process is the same as that of the sharpening, ie several successive passes in the slot 3 of the sharpener are necessary.
Never use on a ceramic blade! This could irreversibly damage or break it!
Please only use slot 3 to sharpen serrated knives

The sharpener has three slots, pull the knife through each slot one by one, from slot 1 to slot 3.
Do not sharpen alternately in the three slots

Sharpening scissors

Put the scissors in the open position, move the blade of the scissors from the end to the handle, repeat the movement as many times as necessary just in that direction.

CARE AND MAINTENANCE

Cleaning

Clean your sharpener with a damp cloth or a mild brush. Do not rinse with water.
Do not put in the dish washer.

Common Faults and Solutions

No work after sharpening:

• Check whether the sharpening is conducted correctly according to the description in the instruction (90° angle)
• Do not put too much pressure on the blade to avoid damaging the grinding heads.

FEATURES

Material : silicon, ABS, diamond, stainless steel, ceramic,carbide

Imported by :
CAPTELEC, 59170 Croix – FRANCE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>