Airpura P700 Plus Air Purifier User Manual
- June 4, 2024
- Airpura
Table of Contents
Airpura P700 Plus Air Purifier User Manual
TO BEGIN USING YOUR AIRPURA
Inspect the exterior of your Airpura to verify there is no damage from
shipping.
If any damage is noted, please follow the instructions from the distributor
returns policy.
Wipe the unit with a damp cloth to remove any dust from packaging
Plug the unit into a regular grounded 110 volt outlet #I j gc i Z j c i dc
Turn on the unit to MAX and allow it to run for at least 30 minutes
Set the variable speed control to the level you wish
Always maintain a humidity level of 40% in your home to ensure the unit is operating at optimal levels. When using purifer with a dehumidifier, please keep dehumidifier at least 6 feet away. It is recommended to run your purifier at low speeds, 24 hours a day, 7 days a week. Running it at a low speed allows for maximum dwell time of chemicals and VOCs in the air through both the carbon and HEPA filters thus delivering superior filtration.
FILTER MAINTENANCE AND REPLACEMENT
The Prefilter
Can be vacuumed from the exterior of the unit once a month or more often.
Should be replaced at least after 12 months of use
To vacuum the Prefilter
Use the brush attachment on your vacuum cleaner Vacuum slowly around the mesh surface of the filter chamber
IMPORTANT SAFETY NOTE
Please ensure air purifier is turned OFF when plugging into a power source.
Failure to do so may result in motor potentially stalling and/or burning.
Replacing the UV bulb
Open the filter chamber following the instructions
Pull the bulb upward out of the connector
Push the replacement bulb firmly into the connector
Close the filter chamber following instructions
-
Titanclean
18-20 months -
HEPA 600RVHU Filter
(99.97 % efficient @ 0.3 Microns)+TiO2 3 to 5 years -
UV bulb
18-20 months -
Poly Prefilter 600 2-pack
12 months -
+ 18 lbs, Coconut Shell Carbon Filter (100% Blend)
24 months
To open the filter chamber
-
Turn over the Airpura
-
Remove the 4 retaining screws
-
Take off the cover
-
Remove the gasket
-
Position the Prefilter inside the filter chamber
-
Place a felt gasket at the bottom of the filter chamber
-
Unfold the filter slider (Supplied with replacement filters or on request Part#6F 001)
-
Roll it into a spiral
-
Insert the tube into the filter chamber inside the Prefilter
-
Let the spiral open to fill the opening
-
Open the top of the spiral to make a slight funnel
-
Insert the Carbon canister into the funnel and hold it straight
-
Let the canister slide down thefilter slider
-
Pull the filter slider up out of the cavity using both hands and let the canister slide to the bottom of the cavity
-
Remove the filter slider and fold it for further use
-
Slide in the Hepa filter
To close the filter chamber
-
Replace the gasket
-
Position the indentation in the cover into the center of the HEPA filter
-
Replace the 4 screws and tighten
-
Turn the Airpura back on casters
Technical specifications
Particle removal
Over 100 ft2
true HEPA
(Measured only 1 side)
12 pleats per inch
Pleats warm rolled with separators
Activated carbon filter
18 lbs carbon filter
13″H X 13.25″OD X 9″ID
Carbon Bed
2” deep X 570 sq. surface
Air Flow 635 cfm
More cfm than any other
home unit available
Prefilter
570 in2 x 1 in
Housing
Powder coat steel
Size
23 in x 15 in
Weight
35 lbs total
Watts
120 on high / 40 on low
Sound Level
30.2 db on low (at 6 feet)
63.0 db on high (635 cfm)
at test conditions
Voltage options
115 or 220 volts
Air purifiers models and filter configurations
Prefilter | Particule | Carbon | |
---|---|---|---|
Alternates | Cotton Prefilter TarBarrier Prefilter | 18 lbs anthracite carbon |
filter (100%)
Upgrade| | HEPA 14 Filter (99.99 % efficient @ 0.3 Microns) ULPA Filter
(99.9999 % efficient @ 0.1 Microns)| 18 lbs impregnated carbon 18 lbs carbon
(17% potassium permaganate carbon, 83% coconut shell
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>