Dogcare PC01 Smart Pet Clipper User Manual

June 4, 2024
Dogcare

dogcare-logo

Dogcare PC01 Smart Pet Clipper

IMPORTANT SAFETY INSTRUCTIONS

BEFORE USING THIS PRODUCT READ ALL INSTRUCTIONS AND
CAUTIONARY MARKINGS IN THIS MANUAL.
KEEP AWAY FROM WATER.

DANGER: To reduce the risk of electric shock:

  1. Do not place or drop into water or other liquid.
  2. Do not use while bathing or in a shower.
  3. Do not handle any part of the charger or product with wet hands.
  4. Do not place or store the product where it can fall or be pulled into a tub or sink.
  5. If the product falls into water, unplug it immediately. Do not reach into the water.
  6. Turn off and unplug the product before cleaning.
  7. Always unplug the product immediately after charging.

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons:

  1. The product is intended for household use only.
  2. Do not use the product for any other purpose than clipping dogs’ or cats’ hair. Do not use on pets under 6 months, pregnant, sick (including skin diseases), or old. Not recommended for aggressive pets.
  3. The product is not intended for use by, on, or near young children, invalids or infirm persons with reduced physical, sensory, or reasoning capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the product by a person responsible for their safety.
  4. Use only as described in this manual. Do not carry out any maintenance other than shown in this manual. Do not use attachments not recommended by DogCare.
  5. Do not store or charge near heat sources.
  6. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
  7. Do not use the product with a damaged or broken attachment comb nor with teeth missing from the blades as injury may occur.
  8. Use only the USB cable provided for charging this product. Do not use with a damaged cable.
  9. If the product is not working as it should, if it has received a sharp blow, if it has been dropped, damaged, or dropped into water, do not use and contact the DogCare customer support.
  10. Contact the DogCare customer support when a service or repair is required. Do not disassemble the product as incorrect reassembly may result in an electric shock or fire.
  11. Contact the DogCare customer support to replace or recycle the battery. Do not attempt to open the product to remove or replace the built-in battery. The battery used in this product may present a risk of fire or chemical burn if mistreated.
  12. When not in use, the product should be unplugged, stored in a safe and dry location, out of reach of children.
  13. The ambient temperature range for operation and charging should be 14°F to 113°F.

READ AND SAVE THESE INSTRUCTIONS
THIS DOGCARE PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY

  • Do not use the product for any other purpose than clipping dogs’ or cats’ hair.

  • Do not put hands under the blades when the product is in use.

  • Do not store or charge near heat sources.

  • The product is not waterproof. Keep away from water.

  • Do not use the product with damaged blades, attachment comb, or power cable.

  • Store in a stable and safe place, out of reach of children.

Quick Start

Charging

Your clipper will need to be fully charged before first use.

Power Modes
Your clipper has three power modes for different tasks.

  • Quiet: Slow and gentle clipping for a precise and detailed result. Runs at a very low volume. Especially suitable for sensitive pets .
  • Turbo: High speed and powerful clipping. Cuts through the thickest coats with a moderate running volume .
  • Smart: Ideal performance for any pet hair. Senses the level and thickness of hair, then automatically adjusts to the optimal clipping speed.

In the Box

  1. Clipper oil
  2. Cleaning brush
  3. USB cable
  4. Grooming comb
  5. Grooming scissors
  6. 3/4attachment comb
  7. 5/8attachment comb
  8. 1/2attachment comb
  9. 3/4attachment comb
  10. 1/8attachment comb
  11. 1/4attachment comb

Installing the attachment combs
Hold the comb with teeth up and snap it finally to the bottom of the clipper blades until you hear a click.

Functions
  • Auxiliary Light
    Provides auxiliary lighting to ensure you have a clear view while clipping, delivering the best-in-class experience.

  • Heavy-Duty Motor
    The optimum balance between performance and quietness.

  • High-Capacity Li-Ion Battery
    The built-in lithium-ion rechargeable battery delivers up to 3 hours of runtime per charge (subjective to the operating environment and the selected power mode).

  • Heatproof Fine Tooth Blades

  • Clip with no extreme heat. The patented aerodynamic cooling design with aluminum alloy prevents the blades from overheating during clipping, protecting your pet at all limes. The precise stainless steel and ceramic blades create a quiet, smooth, and safe grooming experience.

  • Display
    Your clipper is equipped with powerful algorithms that calculate its remaining operation lime, intelligently monitor the blade temperature and service life, and automatically remind you to oil the blades. All these incredible features are displayed in real-time.

  • Smart Mode
    Easily change to DogCare’s original Smart mode by using the SMART button. Senses the level and thickness of hair, then automatically adjusts to the optimal clipping speed.

  • Power Switch/Quiet Mode/ Turbo Mode
    Easily switch between Quiet mode and Turbo mode using the sliding switch.

  • Auxiliary Light Switch/Blade Replacement Reset Button
    Your clipper monitors the service life of the blades intelligently. Reset the monitoring function after replacing the blades, as described in Blade Maintenance on page 18.

  • Charging Port
    Recharges with standard USB included in the box, which works with computer ports, portable power banks, and existing USB power adapters.

Turning on or off the Auxiliary Light

Use the auxiliary lighting function when you need it-according to the current lighting needs and your pet’s tolerance to light. Press briefly the RESET button at the bottom of the handle to turn on or off the auxiliary light.

Display

  • Battery
  • Remaining
  • Operation Time
  • Quiet Mode
  • Oil Blades
  • Reminder
  • Blade Service
  • Life
  • Smart
  • Speed
  • Blade Temperature

Battery

  • The battery icon will flash on and off during charging .
  • Battery is fully charged when the battery icon is steady green.
  • Battery is getting low and needs charging when the battery icon is steady red.

Power Mode

  • This icon will light up when in Quiet mode. Turn the sliding switch to the 1 position to switch to Quiet mode .
  • This icon will light up when in Turbo mode. Turn the sliding switch to the 2 position to switch to Turbo mode.
  • This icon will light up when in Smart mode. Press the SMART button in either Quiet or Turbo mode to switch to Smart mode. Press the SMART button when in Smart mode to exit Smart mode and return to the previous mode

Speed

  • In Quiet mode, the clipper runs at the lowest speed .
  • In Turbo mode, the clipper runs at the highest speed.
  • In Smart mode, the current speed is displayed in real time.

Remaining Operation Time
The remaining operation time (minutes) is displayed in real-time according to the battery power and current clipping Speed.
Dogcare-PC01-Smart-Pet-Clipper-13 Oil Blades Reminder

  • When the clipper is turned on and after every 20 minutes of continuous operation, the oil icon will flash
    to remind you to oil the blades.

Blade Temperature

  • As the temperature of the blades rises, the bars above the thermometer icon light up in a clockwise direction, with one bar representing the lowest temperature and five bars the highest.
  • The screen will alert you when the temperature of the blades is too high (over 140°F). The thermometer icon will flash.

Blade Service Life

  • As the use time of the blades increases, the bars above the maintenance icon will go out in a counterclockwise direction, with five bars representing the longest blade service life and one bar representing the blades have run out of life and should be replaced. The maintenance icon will flash to alert you to replace the blades.

  • After replacing the blades, press and hold the RESET button at the bottom of the clipper handle for 5 seconds to reset the blade life monitoring function. The icon will show five bars again after it is successfully reset.

Charging

Dogcare-PC01-Smart-Pet-Clipper-15

  • The battery icon on the screen will flash on and off during charging.
  • Battery is fully charged when the battery icon is steady green.
  • Battery is getting low and needs charging when the battery icon is steady red.

Connect to a USB port using the cable included in the box. The clipper will not turn on while being charged.

Before Your Clip

Consult Your Veterinarian
To be safe, check with your veterinarian or a professional before grooming. If your pet has a skin condition, please avoid shaving your pet at home unless the veterinarian advises you to do so for medical reason.
Dogcare-PC01-Smart-Pet-Clipper-17

Brush out Coat Thoroughly
Sand and mats can bulled up In your pet’s hair. If they hit the high speed, blades, it will reduce the blade service life or, even worse, cause safety hazards. Therefore, before using the clipper, give your pet a nice brush. Foll01N the direction of hair growth, and patently brush out all the sand, dirt, tangles, and mats. Do not wet your pet’s coat at this point, as this will make brushing mere difficult.

Dogcare-PC01-Smart-Pet-Clipper-18

Give Your Pet a Bath
Bathe your pet to clean his or her coat and skin. We recommend using a mild, tear-free shampoo famulated specifically for pets. Massage and rinse thoroughly.

Dogcare-PC01-Smart-Pet-Clipper-19

Dry and Brush Again
Once bathed, towel dry end blow dry your pet. And then give him or her another brush. Your pets hair should be fully dry and free of tangles when you are done.

Dogcare-PC01-Smart-Pet-Clipper-20

Choose A Safe Place
Choose a Welch Indoor place to da the Job. For best Result’s, the light should be adequately bright and evenly distributed. You need a safe, nonslip surface so that your pet does not slip and fall. If your pet Is a cat or a small to medium-sized dog, a grooming table Is Ideal for the clipping to be performed at a comfortable working height. If your pet Is a large dog, you can work on the floor.

Dogcare-PC01-Smart-Pet-Clipper-21

Restrain Your Pat
To prevent your pet from moving much while you perform clipping, you need to hold him or her In place. Since you will need both hands In do the clipping, you can use a grooming restraint to secure your pet (but da not leave your pet alone on the table In a 198tralnt). Or It may be helpful to ask another person who Is familiar with your pet (a family member or neighbor, etc.) to help. If your pet Is at all resistant, calm him or her down first. Dogcare-PC01
-Smart-Pet-Clipper-22

Desensitize Your Pet
Make sure your pet is in a calm mood. If it is their first cut, it is essential to acclimate your pet. The sound of the clipper operating may trouble some sensitive pets. Tum the clipper on and set it to Quiet mode, and run it close to your pet’s ear for a while to get them used to the noise. In addition, you can help your pet develop a positive connection with the clipper by offering them petting, praise, or treats during clipping.

Dogcare-PC01-Smart-Pet-Clipper-23

Oil the Blades
Blades should be oiled before, during, and after each use. For instructions, please refer to the Blade Maintenance section on page 18. For your pet’s safety, use the clipper’s dedicated oil. Do not use hair oil, grease, or any oil mixed with kerosene or other solvents at any time.

Dogcare-PC01-Smart-Pet-Clipper-24

Power Modes

Your clipper has three power modes for different tasks.

Quiet Mode

  • Turn the sliding switch to the 1 position to switch to Quiet mode.

  • In Quiet mode, the clipper features a slow clipping speed driven by low power intensity and operates at an extremely low volume. It is suitable for thin and fine hair and areas that are difficult to clip. When using the clipper for the first time, and for clipping pets with a more sensitive personality, it is recommended to try Quiet mode first.
    Turbo Mode ~

  • Turn the sliding switch to the 2 position to switch to Turbo mode.

  • In Turbo mode, the clipper features a fast clipping speed driven by high power intensity and operates at a moderate volume. It is suitable for thick and dense hair and areas that need to be clipped quickly.
    Smart Mode

  • Press the SMART button in either Quiet or Turbo mode to switch to Smart mode. Press the SMART button when in Smart mode to exit Smart mode and return to the previous mode.

  • In Smart mode, the clipper senses the level and thickness of hair, then automatically adjusts to the optimal clipping speed. When the hair is thin and fine, the speed is set to gentle and delicate. When the hair is thick and dense, the speed is set to turbo. Check the current clipping speed on the screen in real-time.

Clipping Tips
  1. Select a power mode according to your pet’s hair condition, grooming area, and your pet’s personality. When using the clipper for the first time, and for clipping pets with a more sensitive personality, it is recommended to try Quiet mode first.

  2. There are 6 sizes of attachment combs included in the box to trim the hair to different lengths. From the largest to the smallest:
    The 3/4″ comb leaves hair approximately 3/4″.
    The 5/8″ comb leaves hair approximately 5/8″.
    The 1/2″ comb leaves hair approximately 1/2″.
    The 3/8″ comb leaves hair approximately 3/8″.
    The 1/4″ comb leaves hair approximately 1/4″.
    The 1/8″ comb leaves hair approximately 1/8″.
    For help with installing the attachment combs, please refer to the In the Box section on page 6.
    When using the clipper for the first time, if you are unsure of how long each comb leaves the hair, start by placing the largest comb and make your way down if the desired length is shorter.
    Dogcare-PC01-Smart-Pet-Clipper-28 Clipping Tips

  3. Clip with the growth of the hair. Otherwise, you will create harsh and uneven lines. Move your clipper property by using slow and gentle strokes. Avoid ◄ applying downward pressure to the clippers, as this is likely to cause damage to your pet’s skin.
    Dogcare-PC01-Smart-Pet-Clipper-29

  4. Generally, it is recommended to start clipping from the most challenging areas. Because your pet will tend to become more impatient as time progresses. Typically, the head, paws, underarms, stomach, and bottom are more difficult to clip. The neck, back, and chest are easier. The order can be adjusted accordingly. If your pet is already very nervous at the beginning, you can start from easier areas-for example, the back of the neck-to allow your pet to adapt. Unless your pet is completely still, it is not recommended to use the clipper on your pet’s face, especially around the eyes. Instead, you can use scissors for fine trimming.

  5. Paws easily pick up sand and dirt Before you trim the hair on your pet’s paws, make sure that the hair has been thoroughly cleaned, otherwise it may damage the blades and cause safety hazards. Please refer to the Before You Clip section on page 14. Keeping the hair on your pet’s paws short will help reduce
    the risk of mats building up between their pads which causes painful walks and even injuries. Keep in mind that paws are very sensitive for dogs and cats. Go slow and gentle to give your pet time to adjust. Use the clipper to shave the hair on top of the paws and then carefully trim between the toes. While clipping, check your pet’s paws for any signs of injury. For better grooming results, pair up with the DogCare Nail Grinder. Please visit Dog Care’s Amazon store or
    www.dogcare.net for more information.
    Dogcare-PC01-Smart-Pet-Clipper-30

  6. To trim the underarms, make sure your pet is still and lift his or her leg with a gentle motion. Clip with the growth of the hair-from the armpit to the leg.
    The skin in the underarm area is very delicate and sensitive. Keep an eye on the blade temperature monitoring ion on the screen while clipping. If the temperature gets too high, take a break to cool down the blades—-please refer to the Blade Maintenance section on page 18.
    Dogcare-PC01-Smart-Pet-Clipper-31

  7. Clip the hair on your pet’s stomach to help your pet maintain hygiene when going to the bathroom. Make sure your pet is still and lift his or her leg with a gentle motion. Clip with the growth of the hair, using almost no pressure against the skin. Be careful not to nick the nlpples and genital area. The skin on the stomach is very delicate and sensitive. Keep an eye on the blade temperature monitoring icon on the screen while clipping. If the temperature gets too high, take a break to 0001 down the blades—-please refer to the Blade Maintenance section on page 18.
    Dogcare-PC01-Smart-Pet-Clipper-32

  8. Clipping the hair on your pet’s bottom also helps your pet maintain hygiene when going to the bathroom. Make sure your pet Is still and 11ft his or her leg with a gentle motion. Clip with the growth of the hair, using almost no pressure against the skin. The skin around the anus has folds, so go slow and gentle end be careful not to nick your pet.
    Dogcare-PC01-Smart-Pet-Clipper-33Dogcare-PC01
-Smart-Pet-Clipper-34

Blade Maintenance

Remove and Install the Blades
To remove the blades, with the clipper off, press the blades where they are attached to the clipper’s body with your thumb and push the blades backward firmly. To avoid causing damage to the blades from falling, take care to hold the blades with your hands when removing them. To install the blades, with the clipper off, align the blades with the slot on the back of the clipper’s body, and then push it into the body.

Removing the Blades

When removing and installing the blades, please avoid violent operations, otherwise you may cause injury to yourself. Please
be careful not to allow the blades to hit metal and other hard objects, otherwise it may lead to blade damage.

Clean the Blades
Excess hair and dirt may accumulate between the blades. After removing the blades with the clipper off, you can and clean the hair away with the cleaning brush included in the box or a worn out toothbrush. Do not use water to clean the blades.

Oil the Blades
Blades should be oiled before, during, and after each use. The oil icon on your clipper screen will flash when your blades need lubrication. Turn on the clipper in Quiet mode, and place a few drops of oil on the front and each side of the blades. Leave the clipper running for a couple of seconds for the oil to penetrate evenly between the blades. Then turn off the clipper and wipe excess oil off blades with a soft dry cloth. For the safety of your pet, use the clipper’s dedicated oil. Do not use hair oil, grease, or any oil mixed with kerosene or other solvents at any time.

Installing the Blades

Cool down the Blades
The Heatproof blades featuring a unique aerodynamic cooling design to protect your pet from extreme heat. However, due to the high-speed nature of your clipper, the blade temperature will moderately increase during use. If the blades are not adequately lubricated, the blade temperature will rise rapidly. Please oil the blades as needed.
Your clipper intelligently monitors the blade temperature. Check the current blade temperature on the screen regularly. When clipping sensitive areas such as the stomach, make sure that the blade temperature is comfortable for you pet. If the temperature is too high, you can switch off the clipper and place it in a cool and ventilated place for 5 minutes. If there are replacement blades at hand, you can also replace the blades to continue clipping.

Replacing the Blades
Replace the blades if they are broken or reach the end of their service life (when the blade life monitoring icon on the clipper screen only has one bar left and flashes). Do not use the clipper with a damaged or broken attachment comb nor with teeth missing from the blades as injury may occur. After replacing the blades, press and hold the RESET button at the bottom of the clipper handle for 5 seconds to reset the blade life monitoring function. You can purchase the replacement heatproof blades separately by visiting DogCare’s Amazon store or www.dogcare.net.

Compatible Blades

All DogCare blades are compatible with your clipper. You can purchase replacement blades by visiting Dog Care’s Amazon store or www.dogcare.net.

Heatproof Fine Tooth

  • Default with DogCare PC01 clipper
  • Stay cooler for longer to protect your pet from extreme heat
  • Provide a smoother and cleaner cut and make your pet’s coat feel softer
  • Ideal for grooming and a finishing touch

Heatproof Skip Tooth

  • Stay cooler for longer to protect your pet from extreme heat
  • Best for cutting through thick, curly, or matted hair
  • Ideal for a quick overall cut
  • Can come in handy for grooming bigger dogs

Illumination Fine Tooth

  • Default with DogCare PC02 clipper
  • Provide a smoother and cleaner cut and make your pet’s coat feel softer
  • Ideal for grooming and a finishing touch
  • Work best on dogs with fine or thin hair as well as cats.

Illumination Skip Tooth

  • Best for cutting through thick, curly, or matted hair
  • Ideal for a quick overall cut
  • Can come in handy for grooming bigger dogs

Troubleshooting

Will not charge

  • Check that the household electrics are on-test by plugging in another appliance.
  • Test the clipper in a different USB port.
  • Check the cable for signs of damage. If damaged, stop using and contact DogCare Customer Support

Running time is too short

  • Make sure that the clipper is fully charged before each use.
  • The blades may not be adequately lubricated. Oil the blades before, during, and after each use, as described in Blade Maintenance on page 18.
  • It is normal to have a moderate reduction in battery discharge time due to battery age or use.

Will not switch off

  • The clipper is switched off using the sliding switch.

Stops working or no display

  • Fully charge the clipper.
  • The clipper has a built-in safety mechanism that will automatically stop it if exceeds the safe operating temperature range or if the blades become blocked.
  • The ambient temperature range for operating and charging should be 14°F to 113°F. Do not use it outdoors.
  • The blades may not be adequately lubricated. Oil the blades before, during, and after each use, as described in Blade Maintenance on page 18.
  • The blades may be clogged. Clean and oil the blades while the clipper is off as described in Blade Maintenance on page 18.
  • Switch the clipper on again after trying the above steps. If the clipper is still not working properly, please contact DogCare Customer Support.

No speed difference between modes

  • Please contact DogCare Customer Support.

Unusual noise

  • The level of sound from your clipper will vary depending on the power mode selected. To decrease the noise, use the sliding switch to select Quiet Mode.
  • If the noise is louder than usual, clean and oil the blades with the clipper off as described in Blade Maintenance on page 18.
  • Do not use the product with a damaged or broken attachment comb nor with teeth missing from the blades as injury may occur. Replace the blade

Clipper body overheats

  • The ambient temperature range for operating and charging should be 14°F to 113°F. Do not use it outdoors.
  • The blades may not be adequately lubricated. Oil the blades before, during, and after each use, as described in Blade Maintenance on page 18.
  • The blades may be clogged. Clean and oil the blades while the clipper is off as described in Blade Maintenance on page 18.
  • Do not use the product with a damaged or broken attachment comb nor with teeth missing from the blades as injury may occur. Replace the blades.

Ceramic moving blade does not move

  • Fully charge the clipper.
  • The blades may be clogged. Clean and oil the blades while the clipper is off as described in Blade Maintenance on page 18.
  • Do not use the product with a damaged or broken attachment comb nor with teeth missing from the blades as injury may occur. Replace the blades.

Blades pull hair or cut unevenly

  • Make sure your pet’s hair is dry. The clipper does not clip wet hair properly.
  • The blades may not be adequately lubricated. Oil the blades before, during, and after each use, as described in Blade Maintenance on page 18.
  • The blades may be clogged. Clean and oil the blades while the clipper is off as described in Blade Maintenance on page 18.
  • Do not use the product with a damaged or broken attachment comb nor with teeth missing from the blades as injury may occur. Replace the blades.

Blades overheat

  • The ambient temperature range for operating and charging should be 14°F to 113°F. Do not use it outdoors.
  • The blades may not be adequately lubricated. Oil the blades before, during, and after each use, as described in Blade Maintenance on page 18.
  • The blades may be clogged. Clean and oil the blades while the clipper is off as described in Blade Maintenance on page 18.
  • Do not use the product with a damaged or broken attachment comb nor with teeth missing from the blades as injury may occur. Replace the blades.
  • Switch off the clipper and place it in a cool and ventilated place for 5 minutes, or replace the blades.

Blade service life icon on the display flashes

  • It indicates the blades have run out of life and should be replaced. After replacing the blades, press and hold the RESET button at the bottom of the clipper handle for 5 seconds to reset the blade life monitoring function. The icon will show five bars again after it is successfully reset.
  • If the problem still persists after trying the above solutions, please speak to DogCare Customer Support Team. Do not disassemble the product, as incorrect reassembly may result in an electric shock or fire.
Contact Us

Live Chat
Live chat with us 24n on www.dogcare.net or on Facebook @dogcareglobal.

Scan the QR code to access

Phone
1-833-220-1900
Our helpline hours:

  • 9am – 9pm EST, 6am – 6pm PST
  • 7 days a week

Email
dogcare@afterservlce.vlp
To help us address your inquiry as quickly as possible, please include the following in your email:

  • Your name
  • Phone number
  • Product name or model number

We will respond to your inquiry within 12 hours.

Guarantee Terms and Conditions

DOGCARE CUSTOMER CARE
Thank you for choosing to buy a DogCare product. Your DogCare product will be covered for parts (excluding blades and battery) and labor for 5 years from the date of purchase, subject to the terms of the guarantee. However, indispensable legal rights of the final consumer under applicable national legislation governing
the sales of consumer goods are not affected by the terms of the guarantee.
If you have any queries regarding your DogCare product, visit www.dogcare.net for online help, general tips and useful information about DogCare.
If your DogCare product needs a repair, call DogCare (toll free) at 1-833-220-1900 so we can discuss the available options. If your DogCare product is under guarantee, and the repair is covered, it will be repaired at no cost.

LIMITED 5-YEAR WARRANTY
Terms and conditions of the DogCare 5-year limited guarantee.

WHAT IS COVERED
Your DogCare product is warranted against original defects in materials and workmanship for a period of 5 years from the date of purchase or delivery, when used in accordance with the DogCare User Manual. Please retain your proof of purchase. This warranty provides, at no extra cost to you, all labor and parts (excluding blades) necessary to ensure your product is in proper operating condition during the warranty period (if any part is no longer available or out of manufacture, DogCare will replace it with a functional replacement part). This warranty is only valid if the product is used in the country in which it was sold.

WHAT IS NOT COVERED
DogCare shall not be liable for costs, damages or repairs incurred as a result of, due to, or from

  • Accidental damage, faults caused by negligent use or case, misuse, neglect, careless operation or handling of the product which is not in accordance with the DogCare User Manual.
  • Use of the product for anything other than normal domestic household purposes.
  • Use of parts not assembled or installed in accordance with the DogCare User Manual.
  • Use of parts and accessories other than those produced or recommended by DogCare.
  • Faulty installation (except where installed by DogCare).
    • Repairs or alterations carried out by unauthorized parties or agents.
    • Normal wear and tear (e.g. blades etc.).
  • Reduction in battery discharge time due to battery age or use. If you are in any doubt as to what is covered by your warranty, please contact DogCare.

WARRANTY LIMITATIONS AND EXCLUSIONS
To the fullest extent permitted by applicable law, any implied warranties relating to your product including but not limited to warranty of merchantability or warranty of fitness for a particular purpose, are limited to the duration of this warranty. To the fullest extent permitted by applicable law, your remedy for breach of this warranty is limited to the warranty service described below. DogCare will not be liable for any consequential damages or incidental damages you may incur in connection with your purchase and use of your product. This limited warranty gives you specific legal rights. You may also have other rights which vary by State. This limited warranty is not transferable.

SUMMARY OF COVER
The repair or replacement of your DogCare product under guarantee will not extend the period of guarantee.

The guarantee provides benefits which are additional to and do not affect your statutory rights as a consumer. The guarantee becomes effective from the date of purchase (or to the date of delivery if this is later). You must provide proof of (both the original and any subsequent) purchase/delivery before any work can be carried out on your DogCare product. Without this proof, any work carried out will be chargeable. Keep your receipt or delivery note. All work will be carried out by DogCare or its authorized agents. Any parts which are replaced by DogCare will become the property of DogCare.

CONFORMITY INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Technical Specifications
  • Product Name  DogCare Smart Pet Clipper
  • Model PC01
  • Weight 11.1 oz
  • Dimensions 7.6 X 2.4 X 2.2 in
  • Motor Power 3.2W
  • Battery Type Built-in rechargeable lithium-ion battery
  • Battery Capacity 2200mAh
  • Charging Time Approx. 3.5 hours
  • Battery Runtime Approx. 3 hours
  • Operating Ambient Temperature 14°F to 113°F
  • Relative Humidity <75%

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals