DOGCARE TC01-PR0-T Dog Training Collar User Manual

June 15, 2024
Dogcare

Dog Training System

Model: TC0O1 PRO
www.dogcare.net

IMPORTANT SAFETY INSTRUCTIONS

BEFORE USING THIS PRODUCT READ ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL.

WARNING
To reduce the risk of burns, fire, electric shock, or injury to persons:

  1. This product is designed for use with dogs where training is desired. Do not use this product for anything other than its intended purpose.

  2. The specific temperament of your dog may not work with this product. Do not use this product if your dog has any medical conditions. Do not use this product if your dog s aggressive or if your dog s prone to aggressive behavior.
    Aggressive dogs can cause severe injury and even death to their owner and others.
    If you are unsure whether this is appropriate for your dog, please consult your veterinarian, certified trainer, or contact Dog Care customer support.

  3. We recommend that you not use this product f your dog is under 6 months of age or less than 8 pounds

  4. NOT ATOY. This product is not intended for use by, on, or near young children, invalids or infirm persons with reduced physical, sensory, or reasoning capabilities, or lack of experience and knowledge, unless they have been given Supervision or  instruction concerning use of the product by a person responsible for their safety. To reduce the risk of injury, close supervision is necessary when the product s used near children

  5. Do not operate the product i it has a damaged electrical power cord o plug, or if tis malfunctioning or has been damaged. Contact Dog Care customer support for further instructions.

  6. Contact Dog Care customer support to replace or recycle the battery. Do not attempt to open the product to remove of replace the built-in battery. Do not incinerate, puncture, deform, or short-circuit. The battery used in this product may present a risk or chemical bur if mistreated

  7. Risk of explosion i battery is replaced by an incorrect type. Do not attempt to cut into or pry open the battery, dispose of in fire, or expose to water. Dispose of spent batteries according to the regulations in your area

CAUTION

  1. The product is designed to get your dog’s attention, not to punish. However, the initial stimulation may startle your dog. Do not leave your dog alone when using the product for the first time.

  2. Do not connect a lead/leash, tags, or other items to the collar; it will cause excessive pressure on the CONTACT POINTS. Attach a lead leash and/or tag to a separate regular collar or a hams. When using a separate collar, make sure the extra collar does not put pressure on the CONTACT POINTS.

  3. Avoid leaving the collar on your dog for more than 12 hours per day.

  4. When possible, reposition the collar on the dogs neck every one to two hours.

  5. Check the fit to prevent excessive pressure; follow the instructions in this ‘manual. Do not make the collar any tighter than is required for good contact. A collar that is too tight will increase the risk of pressure necrosis in the contact area.

  6. Examine the contact area daily for signs of a rash or a sore.
    If a rash or sore is found, discontinue use of the collar until the skin has healed.
    If the condition persists beyond 48 hours, see your veterinarian.

  7. The collar is water-resistant but is not suitable to be submerged. Remove the collar when your dog needs to swim and paddle

  8. To ensure water resistance, cover the RUBBER PLUG of the charging port after each charge.

  9. Contact Dog Care customer support when a service or repair is required Unauthorized changes or modifications to the equipment may violate FCC regulations and could void the user’s authority to operate the equipment.

READ AND SAVE THESE INSTRUCTIONS

QUICK START

Your upgraded dog training system features a silicone CONTACT POINTS module. The CONTACT POINTS are made entirely of flexible conductive silicone to ensure a more comfortable and safe experience for your dog

DOGCARE TC01-PR0-T Dog Training Collar - Fig 2

‘The CONTACT POINTS module is detachable for replacement. Before you remove or install the module, make sure the collar is tumed off—press and hold the ON/OFF BUTTON for 2 seconds to tum off the collar.
To install the module, align the tab on the bottom of the module with the hole on the. receiver unit, then rotate the module clockwise until you hear a click

DOGCARE TC01-PR0-T Dog Training Collar - Fig 3

Charge the collar and remote control with the included USB cable. Charging takes approximately 3 hours respectively.

DOGCARE TC01-PR0-T Dog Training Collar - Fig 4

Collar fitting: when wearing the collar, the tightness is at most it if one finger can be inserted underneath. Make sure the CONTACT POINTS on the collar are placed snugly against your dog’s skin.

DOGCARE TC01-PR0-T Dog Training Collar - Fig 5

Turn on the collar: hold the ON/OFF BUTTON for 2 seconds.
Turn on the remote control: rotate the ON/OFF SWITCH clockwise.

DOGCARE TC01-PR0-T Dog Training Collar - Fig 6

Unlock/Lock the remote control keypad: toggle the KEYPAD LOCK down to unlock, and up to lock.

DOGCARE TC01-PR0-T Dog Training Collar - Fig 7

Vibrate command: press the VIBRATE BUTTON briefly, and the collar will vibrate once.

DOGCARE TC01-PR0-T Dog Training Collar - Fig 8

Beep command: press the BEEP BUTTON briefly, and the collar will beep once.

DOGCARE TC01-PR0-T Dog Training Collar - Fig 9

Static command: press the STATIC BUTTON briefly, and the collar will apply a static stimulation.

DOGCARE TC01-PR0-T Dog Training Collar - Fig 10

Static intensity adjustment: press and hold the LEVEL BUTTON while rotating the ON/OFF SWITCH to adjust the static intensity.

DOGCARE TC01-PR0-T Dog Training Collar - Fig 11

Channel switching: it is possible to train 9 dogs at the same time. Press the CHANNEL BUTTON briefly to select which collar to control.

DOGCARE TC01-PR0-T Dog Training Collar - Fig 12

Pairing: The default set of remote control and collar has been paired with channel #1 through factory setting. To pair an additional collar, refer to page #12 for more information.

COLLAR STATIC STIMULATION

QUICK GUIDE

When wearing the collar, it is most suitable if one finger can be inserted under it. Too tight is not good for your dog, but too loose will dull the static function for the CONTACT POINTS cannot touch your dog’s skin.

Not Feeling the Static? Try These Solutions

If your dog has thick fur, please separate the fur apart 5o that both CONTACT POINTS can touch the skin

Make sure the CONTACT POINTS module is properly attached 1o the collar and has good contact. To attach the module, rotate it clockwise until you hear a click.

Water can help con duct electricity. If you spray some water around the CONTACT POINTS, the static function can work more effectively

One last thing you can try is to shear the fur where both CONTACT POINTS are touched.

Note:

  1. Only when both CONTACT POINTS are simultaneously touched, the static will work,
  2. If the collar has a delayed reaction o fails to sync up even in a short distance, make sure there is no strong signal interference in your surroundings. The remote’s range could be affected by obstacles, electromagnetic field, or even stormy weather.
  3. If you find the collar not working, please check whether you have pushed up the KEYPAD LOCK which is on the left side of the remote.
  4. The sensitivity to static depends on your dog’s size, weight, amount of fur, and ‘even skin condition

Function:

DOGCARE TC01-PR0-T Dog Training Collar - Fig 18

Setting up

1. Charge the devices for at least 3 hours repectively.
a. Remote control: charge the device until the REMOTE CONTROL BATTERY on the DISPLAY indicates full bars.
b. Collar: charge the device until the red STATUS LED turns green. When the red light flashes, it indicates low battery.

DOGCARE TC01-PR0-T Dog Training Collar - Fig 19

Static intensity adjustment: press and hold the LEVEL BUTTON while rotating the ON/OFF SWITCH to adjust the static intensity.

Adjust the static intensity on an individual basis. The sensitivity to static. depends on your dog’s size, weight, amount of fur, and even skin condition.

Wearing the Collar

Make sure that the collar is powered o

Have your dog stand in a balanced position on a flat, even surface.

Put the strap over your dog’s neck, centering the collar underneath its neck and making sure that the Dog Care logo is upright facing you.

Tighten the strap so that i fits snugly on your dog’s neck and should not be able to rotate around the neck. The. tightness is at most fit f one finger can be inserted underneath

NOTE: the collar should it tightly and should not be able to rotate or slide on your dogs neck.
Your dog must be able to swallow food and water normally. You should observe your dog’s behavior to verify that the collar is not too tight.

Wiggle the collar to work the CONTACT POINTS through the dog’s coat.
NOTE: The CONTACT POINTS must have contact with the dog’s skin to be effective.
If your dog has thick fur, please separate the fur at the CONTACT POINTS with a comb to enable them to reach the skin

When you are satisfied with the fit of the collar, you may want to adjust the excess strap length. After removing the collar, you can put the strap’s end back through the buckle, o trim away excess strap length and seal the strap’s end with a lighter or candle flame.
NOTE: remove the collar first.

In case the collar strap is damaged, you can replace the strap. Insert a pointed tool into the slot and push to detach the strap. Visit Dog Care’s Amazon store to find out more about the replacement collar strap.

Training Modes

  1. Vibration Mode:
    Press the VIBRATE BUTTON, and the collar will vibrate once; hold the button and the vibration persists.DOGCARE TC01-PR0-T Dog Training Collar - Fig
28

  2. Beep Mode:
    Press the BEEP BUTTON, and the collar will give a “beep” sound; hold button, and the “beep” sound persists.DOGCARE TC01-PR0-T Dog Training Collar - Fig
29

  3. Static Mode:
    Press the STATIC BUTTON, and the collar will release a static stimulation.DOGCARE TC01-PR0-T Dog Training Collar - Fig
30Do not hold the static button as it is not recommended to have prolonged static stimulation to your dog (the static will be cut off automatically in 4 seconds to prevent unintentional stimulation)

  4. Switching Channel:
    Press the CHANNEL BUTTON to choose which collar to control when paired with multiple collars.

DOGCARE TC01-PR0-T Dog Training Collar - Fig 31

Pairing

*The defult set is already paired by factory setting and ready to use.

  1. Ensure the collar is turned off. Hold the ON/OFF BUTTON  of the collar for 5 seconds until the STATUS LED on the collar flashes in green.
  2. Press and hold the CHANNEL BUTTON for 3 seconds. The collar will vibrate and beep which indicates the pairing is completed. You will see “1” (or subsequent number) in the CHANNEL DISPLAY when the pairing is successful.

DOGCARE TC01-PR0-T Dog Training Collar - Fig 33

Adding multiple collars:
After confirming the collar is turned off, hold the ON/OFF BUTTON of the collar for 3 seconds, release the button after the STATUS LED on the collar flashes in green. Press and hold the CHANNEL BUTTON on the remote for § seconds (repeat step 1 and 2). The CHANNEL DISPLAY will show the subsequent number of the new collar. Note: connect only one collar at a time. Do not connect all simultaneously, or the remote will pair all collars into a single channel.

DOGCARE TC01-PR0-T Dog Training Collar - Fig 34

Removing all paired collars:
Press and hold the LEVEL BUTTON and the BEEP BUTTON simultaneously for 5 seconds. Make sure all collars to be removed have sufficient power so that the collars can receive the remove command.

DOGCARE TC01-PR0-T Dog Training Collar - Fig 35

Trouble Shooting

  1. Remote / collar runs out of power quickly
    Make sure the charger and the remote/collar are securely connected.
    Charge the device for 3 hours or above.

  2. Remote does not respond
    Recharge the remote.
    Check the KEYPAD LOCK, and unlock the remote.
    Pair the remote and collar again.

  3. Collar does not respond
    Make sure the collar has been paired
    Check the remote, making sure the collar is on the corresponding channel.
    Check the remote, making sure both the remote and collar have sufficient power.

  4. Training system has no effect on my dog
    Make sure the collar has been turned on, and the CONTACT POINTS are placed snugly against your dog’s skin.
    Check if you are using the static mode with the no-static CONTACT POINTS module installed on the collar.
    Try increasing the static level.

  5. Training mode fails to sync up even in a very short distance
    Make sure there is no strong signal interference in your surroundings. The remote’s range could fluctuate subjects to obstacles, electromagnetic field, or even stormy weather.

  6. Collar beeps, vibrates or applies static stimulation by itself occasionally or constantly
    Make sure no button of the remote has been pressed or gotten stuck.
    Pair the collar with the remote once again.

Please feel free to contact our support team via

**** 1:633.220-1900
dogeare@afterservice.vip
2417 live chat-scan the QR code to access

https://dogcare.afterservice.vip.utm_source=card&utm_medium=qrcode

Training Tips

  1. The device is used for training dogs only; please do not use it for any other purposes.
  2. Do not use the device on dogs aged below 6-month, old, pregnant, easily frightened, aggressive, in heat, or in inferior health conditions.
  3. Use verbal commands first, and supplement with corrective stimulus only as needed. Be consistent with your verbal commands; use the same word every time. Work with your pet on one behavior at a time to avoid confusion and frustration. Reward your dog with food/treats will usually help to achieve the best result
  4. Use as little stimulus as possible and only to reinforce verbal commands when necessary. Do not overcorrect your dog
  5. For example, use the beep sound as warning by pressing the BEEP BUTTON. The dog will become conditioned to the beep preceding the corrective stimulus and will soon learn to recognize the beep as a warning along with your verbal command.
  6. Do not rely on this product solely to train your dog. Some dogs will not respond to this product. We cannot guarantee the effectiveness of this or any trainer on your dog % If your dog shows signs of growling, snarling, biting, or aggression while using the collar, discontinue use immediately and contact a professional trainer for advice.

Safety Guidelines

  1. It is strictly prohibited to disassemble the collar in any situation. Doing so will likely compromise the waterproof function and thus voiding the product warranty.
  2. To guarantee the normal diving function, please insert the waterproof rubber charging lid in place.
  3. Please use the remote control and the collar from the complete set. Do not use other product to match with the collar.
  4. If you want to test the product, please use professional testing apparatus. Do not test with hands, so as to avoid accidental injury.
  5. If find water at the charging port, please wipe it dry before charging.
  6. The collar is not a regular traction collar and not recommended to attach a leash to walk your dog. Doing so during pulling may hurt the dog due to protruding electrodes on the collar.
  7. Do not put the collar on for over 12 hours, as it may cause rashes or discomfort to your dog’s skin.

Terms of Use and Limitation of Liability

  1. Use of this product means you accept all the terms and conditions.
  2. This product is a professional dog training device. You are not recommended to use this product if your dog is clever and less than 8 pounds in weight. If you’re not sure whether the product is suitable for your pet dog, please consult the professional handler or contact us.
  3. This product is a professional dog training device and cannot be used for other purposes. Please do not violate local laws in using this product
  4. We are not responsible for any direct or indirect damages caused by use or misuse of this product; all risks in using this product are the responsibility of the user.
  5. Please contact the dealer for parts warranty, goods return or exchange. We provide technical support only.
  6. We reserve the right to change the terms, conditions and notices of this product are offered

FCC Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
  • Consult the dealer or an experienced radio/TV technician for help.

This product does not contain any user-serviceable parts. Repairs should only be made by an authorized Dog Care service center. Unauthorized repairs or modifications could result in permanent damage to the equipment, and void your warranty and your authority to operate this device under Part 15 regulations.
“This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance Ocmbetween the radiator and your body

Product Specifications

Model TC01 PRO
Collar adjustable range 9.45″-27.5″
Water rating Collar: IP67 waterproof Remote: non-waterproof; keep away from

water
Battery| Collar: 235mAh Remote: 235mAh
Charging voltage| Collar: DC 5V/500mA Remote: DC 5V/500mA
Charging time| 3 hours
Charging interface| Micro USB
Operation environment| 32°F-104°F, <95% RH
Estimated standby time| Collar: 15 days Remote: 45 days
Signal range| 1,000 ft

+1-833-220-1900
9am-9pm ET 6am-6pm PT
dogcare@afterservice.vip
@dogeareglobal
**** @dogeare_global

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals