Westinghouse PWUC Water Broom Undercarriage for Pressure Washers Instruction Manual

June 5, 2024
Westinghouse

Westinghouse PWUC Water Broom Undercarriage for Pressure Washers Instruction Manual

Westinghouse PWUC Water Broom Undercarriage for Pressure Washers Instruction
Manual

⚠ WARNING
Do not use for commercial use. User must read and understand the operator’s manual for their pressure washer before using this accessory to reduce the risk of injury. Before beginning any cleaning activity, spray the pressure stream in a safe direction to make sure that all accessories are connected properly in order to minimize the danger of injury or property damage. Fits most pressure washers. Before using this attachment, make sure it is compatible and is correctly installed. Risk of fluid injections. Do not point at people, pets, electrical devices, or the unit itself. Wear eye protection designated to conform with ANSI Z87.1. Before adding, replacing, or modifying accessories, turn off the pressure washer, release the water pressure in the trigger handle, and lock the trigger handle’s lock out (if one is provided with your pressure washer). Use only with cold water and only outdoors. Store the accessory indoors. Save these guidelines. Use them to train other users and refer to them frequently. Give the user of the tool these instructions as well.

PRODUCT SPECIFICATIONS

Connections …………………………………………………………………………………………………. 1/4 in. QD Plug Broom Width……………………………………………………………………………………………………………….16 in. Maximum Pressure…………………………………………………………………………………………………4,000 psi
Minimum Pressure …………………………………………………………………………………………………2,200 psi
Maximum Water Flow. …………………………………………………………………………………………….. 4.0 gpm
Minimum Water Flow. ……………………………………………………………………………………………… 2.0 gpm
Maximum Water Temperature ……………………………………………………………………………..194°F (90°C)
NOTE: Consult your pressure washer’s operator manual for its maximum operating water temperature.

APPLICATIONS

You may use this product for the purpose(s) listed below:

  • Cleaning decks, sidewalks, and driveways
  • Cleaning the undercarriage of trucks, SUVs, cars, commercial vehicles and trailers

INSTALLING THE WATER BROOM ON THE SPRAY WAND

See Figures 1-2.
Your water broom comes with two straight extension wands and one 90 degree extension wand. The extension wands can be used in multiple configurations as needed for your project.

  • Insert the water broom inlet plug into one of the straight extension wands. Pull back the quick connect coupler and secure. Repeat with the second spray extension wand if additional length is needed.
  • Connect the 90 degree spray extension wand to the second straight spray extension wand. Secure with the quick connect coupler.
  • Insert the end of the 90 degree spray extension wand into the pressure washer’s spray lance and secure with the quick connect coupler.
    NOTE: Be sure the water broom is securely locked into the lance before use.

⚠ WARNING
Only use the water broom on flat, horizontal surfaces. To reduce the risk of injection or injury, never lift the water broom from the cleaning surface while operating the pressure washer.

USING THE WATER BROOM

See Figure 3.

  • After installing the water broom, connect the hose to the pressure washer as described in your pressure washer manual.
  • Pull the pivot knob out and move the pivot coupler forward or back to achieve the desired nozzle orientation.
  • Use with the nozzles pointed down and forward (pivot coupler in back position) to wash large flat surfaces like sidewalks or driveways.
  • To clean the underside of raised items like your car’s undercarriage, pivot so the nozzles are pointed upward (pivot coupler in forward position).
  • Place the water broom on the horizontal surface being cleaned and start the pressure washer.
  • Squeeze the trigger and move slowly allowing the unit to clean the surface.
  • Walk slowly behind the water broom, cleaning as you go.

NOTE: Swirling or striping in the cleaned surface indicates you may be moving too quickly. If a slower pace doesn’t stop the condition, the water broom nozzles may be clogged.
See Nozzle Maintenance to clean the nozzles.

⚠ WARNING
Avoid striking any raised obstacles while using the water broom as damage may occur to the unit. Continuing use could result in serious injury or damage to the unit.

⚠ WARNING
To reduce the risk of injection or injury, do not depress the trigger until the water broom nozzles are completely underneath the surface being cleaned, and always release the trigger before removing the water broom from underneath the surface.

NOZZLE MAINTENANCE

See Figure 4.
The water broom comes assembled. The nozzles are approved for use with pressure washers operating at 2200 to 4000 PSI with a maximum flow rate of 4.0 GPM (2.0 GPM minimum). A pulsing sensation felt while squeezing the trigger and/or a higher vibration in the water broom may be the result of a clogged or dirty nozzle.

  • Turn off the pressure washer and shut off the water supply. Place unit on the ground and pull the trigger to release the water pressure in the lance.

  • Pull back the quick-connect collar to disconnect the water broom from the lance.

  • Use a nozzle cleaning tool or a fine needle to free any foreign materials that are clogging or restricting the nozzle.

  • Use a garden hose to back-flush the nozzle and force out the debris.
    NOTE: Never point the nozzle outlet at your face.

  • Reconnect the water broom to the lance.

  • Turn on the water supply and start the pressure washer to resume cleaning.
    BSWB16WM01 11/9/23 (REV:01)

Westinghouse PWUC Water Broom Undercarriage for Pressure Washers Instruction
Manual - FIG. 1

  • A – Inlet adapter
  • B – Quick connect coupler
  • C – L-wand
  • D – Straight wand

Westinghouse PWUC Water Broom Undercarriage for Pressure Washers Instruction
Manual - FIG. 2

  • A – Pivot knob
  • B – Pivot coupler

Westinghouse PWUC Water Broom Undercarriage for Pressure Washers Instruction
Manual - FIG. 3,4,5

  • A – Needle
  • B – Nozzle
  • A – Filter
  • B – Pivot coupler

REPLACING THE FILTER SCREEN

See Figure 5.
If the water still doesn’t flow freely after cleaning the nozzles, it may be necessary to replace the filter screen. Replacement filter screens are available by calling our Service Hotline at 1-855-944-3571.

  • Turn off the pressure washer and shut off the water supply. Place unit on the ground and pull the trigger to release the water pressure in the lance.
  • Disconnect the surface cleaner from the lance.
  • Using a screwdriver or pair of tweezers, remove the retaining ring and filter screen from the inlet plug.
  • Once the filter screen is removed from the inlet plug, replace it with a new filter screen (not included).
  • Make sure the filter screen is seated inside the inlet adapter and no longer visible above the top of the adapter.
  • Reinstall the retaining ring and push into place until it is secure against the filter screen.

REPLACEMENT PARTS

Replacement parts are available from our Service Hotline at 855-944-3571.

Nozzle …………………………………………………………………………………………………………..BSWB16WA01
Filter Screen…………………………………………………………………………………………………..BSWB16WA02

Service Hotline: 1-855-944-3571
777 Manor Park Drive, Columbus, OH43228
and Westinghouse are trademarks of Westinghouse Electric Corporation.
Used under license by MWE Investments, LLC.
©2023 MWE Investments, LLC All Rights Reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Westinghouse User Manuals

Related Manuals