ARDESTO MGL-2250R Electric Meat Grinder Instruction Manual
- June 4, 2024
- ARDESTO
Table of Contents
**ARDESTO MGL-2250R Electric Meat Grinder Instruction Manual
**
SAFETY GUARDS
This appliance is equipped with a thermostat system. This system will
automatically cut off the power supply to the appliance in case of
overheating.
If you appliance suddenly stops running:
-
Pull the mains plug out of the socket.
-
Press the switch button to turn off the appliance.
-
Let the appliance cool down for 60 minutes.
-
Put the mains plug in the socket.
-
Switch the appliance on again.
-
Please contact your dealer of an authorized service center
if the thermostat system is activated too often. -
If you plug in, the indicator light will be on.
-
This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.
-
Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved.
-
Children shall not play with the appliance.
-
Switch off the appliance and disconnect from supply before changing accessories or approaching parts that move in use.
CAUTION! In order to avoid a hazardous situation, this appliance must never be connected to a time switch.
-
Read these instructions for use carefully and look at the illustrations before using the appliance.
-
Before use, tight the fixing ring by spanner, make sure the ring can not be detach by 4 Nm.
-
Keep these instructions for future reference.
-
Check if the voltage indicated on the appliance corresponds to the local mains voltage before you connect the appliance.
-
Never use any accessories of parts from other manufacture. Your guarantee will become invalid if such accessories or parts have been used.
-
Do not use the appliance if the mains cord, the plug or other parts are damaged.
-
If the power cord of this appliance is damaged, it must always be replaced by manufacture or a service center authorized, in order to avoid hazardous situations.
-
Thoroughly clean the parts that will come into contact with food before you use the appliance for the first time .
-
Unplug the appliance immediately after use.
-
Never use your finger or an objection to push ingredients down the feed tube while the appliance is running. Only the pusher is to be used for this purpose.
-
Keep the appliance out of the reach of children.
-
Never let the appliance run unattended.
-
Switch the appliance off before detaching and install any accessory.
-
Wait until moving parts have stopped running before you remove the parts of the appliance.
-
Never immerse the motor unit in the water or any other liquid, nor rinse it under the tap. Use only a moist cloth to clean the motor unit.
-
Do not attempt to grind bones, nuts or other hard items.
-
Never reach into the cutter housing. Always use the pusher.
-
Mincers are fed with sinewless, boneless and fatless beef that has been cut into pieces approximately 20 mm x 20 mm x 60 mm. Do not use the appliance for more than 5 minutes consecutively. Leave the appliance to cool for 10 minutes before using again.
-
Accessories shall include instructions for their safe use.
-
It shall warn of potential injury from misuse.
-
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been give supervision or instruction concerning use of the appliance by a person responsible for their safety.
-
Children should be supervised to ensure that they do not play with the appliance.
-
If the appliance is locked, please press Reversal button (REV). The meat locked in cutter housing is untrodden, so the appliance can renew its usual condition.
-
Disposal of appliances and batteries.
-
This appliance can be used by children aged from 8 years and above if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved.
Cleaning and user maintenance shall not be made by children unless they are aged from 8 years and above and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years. -
This appliance is intended to be used in household and similar applications such as:
- staff kitchen areas in shops, offices and other working environments;
- farm houses;
- by clients in hotels, motels and other residential type environments;
- bed and breakfast type environments.
Please read carefully and keep the instruction well In order to avoid rust we advise you to lubricate the cutter unit and the grinding discs with some vegetable oil.
DESCRIPTION
- Body
- ON/0/R (ON/OFF/ Reverse)
- Inertia switch
- Fasten button
- Tube inlet
- Food pusher
- Hopper plate
- Head Tube
- Snake
- Cutting blade
- Cutting plate (fine)
- Cutting plate(medium)
- Cutting plate (coarse)
- Fixing ring
- Sausage
- Kebbe
- Rum shredding (fine)
- Drum shredding (medium)
- Drum slicing
- Drum shredding (coarse)
- Pusher
- Feeder
EQUIPMENT:
Disassembled meat grinder – 1 pc.
Nozzle for making sausage – 1 pc.
Nozzle for making “kebbe” – 1 pc.
Nozzles for graters and shredders – 4 pcs.
Instruction manual – 1 pc.
Warranty card (added to the instruction manual) – 1 pc
INSTRUCTION FOR USE
Assembling
- Press the fasten button, hold the head and insert it into the inlet when inserting please pay attention the head must be slanted as per arrow indicated on the top, see (fig.1) , then move the head anticlockwise so that the head being fastened tightly. (fig.2)
- Place the snake into the head, long end first, and turn to feed the screw slightly until it is set into the motor housing. (fig.3)
- Place the cutting blade onto the snake shaft with the blade facing the front as illustrated (fig.4). If it is not fitted properly, meat will not be grinded.
- Place the desired cutting plate next to the cutting blade, fitting protrusions in the slot. (fig.5)
- Support or press the center of the cutting plate with one finger then screw the fixing ring tight with another hand (fig.6). Do not over tighten.
- Place the hopper plate on the head and fix it into position.
- Locate the unit on a firm place.
- The air passage at the bottom and the side of the motor housing should be kept free and not blocked.
Mincer
-
Insert the worm shaft into the cutter housing, the plastic end first.
Place the cutter unit onto the worm shaft. (The cutting edges should be at the front) Place the medium grinding disc or coarse grinding disc (depending on the consistency you prefer) onto the worm shaft. (Make sure the notch of the grinding disc fit onto the projections of the mincer head.) Turn the screw ring in the direction of the arrow on the cutter housing until it is properly fastened. -
Attach the cutter housing to the motor unit.
-
Place the tray on the upright part of the cutter housing.
-
Now the appliance is ready for mincing.
Cut the meat into 10cm-long, 2cm-thick strips. Remove bones, pieces of gristle
and
sinews as much as possible. (Never use frozen meat!)
Put the meat in the tray. Use the pusher to gently push the meat into the
cutter hosing. (For steak tartare , mince the meat with the medium grinding
disc twice. ) (fig.7)
Plug the unit on and switch3/4 knob to “3” , then switch ON/0/R knob to “ ON “
position. After use it, Plug the unit on and switch 3/4 knob to “4”, then
switch ON/0/R knob to “ R “ position.
Making kebbe
-
Insert the worm shaft into the cutter housing, the plastic end first. (fig.8)
Place the cone in the cutter housing.
Place the former on the cutter housing and screw the ring on the cutter housing. (fig.9) -
Attach the cutter housing to the motor unit.
-
Place the tray on the upright part of the cutter housing.
-
Now the appliance is ready for making kebbe. (fig.10)
Feed the prepared kebbe mixture through the kebbe maker. Cut the continuous hollow cylinder into the desired lengths and user as required.
Kebbe is a traditional Middle Eastern dish made primarily of lamp and bulgur wheat which are minced together to form a paste the mixture is extruded through the kebbe maker and cut into short lengths. The tubes can then be stuffed with a minced meat mixture, the ends pinched together and then deep fried.
Making sausages
-
Mince the meat
Insert the worm shaft into the cutter housing, the plastic end first. (fig.11)
Place the separator in the cutter housing.
Place the sausage horn on the cutter housing and screw the ring on the cutter housing.
(Make sure the notches of the separator fit onto the projections of the mincer head.) -
Attach the cutter housing to the motor unit.
-
Place the tray on the upright part of the cutter housing.
-
Now the appliance is ready for making sausages.
Put the ingredients in the tray. Use the pusher to gently push the meat into
the cutter housing.
Put the sausage skin in lukewarm water for 10 minutes. Then slide the wet skin
onto the sausage horn. Push the (seasoned) minced meat into the cutter
housing. If the skin gets stuck onto the sausage horn, wet it with some water.
SHREDDER
- Press the fasten button, hold the plastic cutter housing and insert it into the tube inlet (when inserting please pay attention the plastic cutter housing must be slanted as per arrow indicated), then move the plastic cutter housing anticlockwise until it is fastened tightly, and release the fasten button .(fig.1)
- Place the shredder drum into the plastic cutter housing, then move the shredder clockwise so that it being properly fastened.(fig.2)
- Place the pusher on the upright part of the plastic cutter housing, and use the pusher to gently push the vegetable into the plastic cutter housing.(fig.3)
- Now the appliance is ready for cutting.
Making noodle
- Operation time shall not exceed 3 minutes.
- Use cutting plate 11 or 12 or 13.
- Fill the tray with flour continuely.
HOW TO CLEAN YOUR APPLIANCES
Meat left behind in the cutter housing may be removed from the inside of the
appliance by passing a slice of bread through the cutter housing.
- Before you clean the appliance, switch the appliance off and remove the plug from the socket .(fig.12)
- Press the release button and turn the whole cutter housing in the direction of the arrow. Remove the pusher and the tray .(fig.13)
- Unscrew the screw ring and remove all parts of the cutter housing. Do not clean the parts in the dishwasher!
- Wash all parts that have come into contact with meat in hot soapy water. Clean them immediately after use.
- Rinse them with clear hot water and dry them immediately.
- We advise you to lubricate the cutter unit and the grinding discs with some vegetable oil.
Disposal of appliances and batteries
After the implementation of the European Directive 2002/96/EU in the national legal system, the following applies:
Electrical and electronic devices may not be disposed of with domestic waste. Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details to this are defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations. By recycling, reusing the materials or other forms of utilising old devices, you are making an important contribution to protecting our environment.
Warranty conditions:
The plant guarantees normal operation of the product within 12 months from the
date of the sale, provided that the consumer complies with the rules of
operation and care provided by this Manual.
Service life of the product is 5 years.
In order to avoid any misunderstanding we kindly ask you to carefully study
the Owner’s Manual, the terms of warranty, and check the correctness of
filling the Warranty Card. The Warranty Card is valid only if the following
information is correctly and clearly stated: model, serial number of the
product, date of sale, clear seals of the companyseller, signature of the
buyer. The model and serial number of the product must correspond to those
specified in the Warranty Card.
If these terms are violated, and if the information specified in the Warranty
Card is changed, erased or rewritten, the Warranty Card is considered invalid.
Setup and installation (assembly, connection, etc.) of the appliance are
described in the attached documentation; they can be carried out both by the
user, and by specialists having the necessary qualification sent by USC or
selling companies (on a paid basis). In this case, the person (the
institution) installing the appliance shall be responsible for the correctness
and quality of installation (setup). Please pay attention to the importance of
the correct installation of the appliance, both for its reliable operation,
and for obtaining warranty and free service. Require the installation
specialist to enter all the necessary information about the installation in
the Warranty Card.
In case of failure of the appliance during the warranty period by the fault of
the manufacturer, the owner is entitled to free warranty repair upon
presentation of the correctly filled Warranty Card together with the appliance
in the factory configuration packed in the original packaging to the warranty
workshop or the place of its purchase. Satisfaction of the customer’s claim
due to the fault of the manufacturer shall be made in accordance with the law
«On Protection of
Consumers’ Rights». In the case of warranty repair the warranty period shall
be extended for the period of repair and shipment.
WARRANTY CARD
Dear Buyer! Congratulations on your purchase of the ARDESTO brand appliance, which was designed and manufactured in accordance with the highest quality standards, and we thank you for choosing this particular instrument.
We ask you to keep the coupon during the warranty period. When purchasing a product, require a full warranty card.
- Warranty service is carried out only if there is a correctly and clearly filled original warranty card, which indicates: product model, date of sale, serial number, warranty service period, and the seller’s seal. *
- The service life of household appliances is 5 years.
- The product is intended for consumer use. When using the product in commercial activities, the seller / manufacturer does not bear warranty obligations, after-sales service is performed on a paid basis.
- Warranty repair is carried out within the period specified in the warranty card for the product in an authorized service center on the conditions and terms determined by applicable law.
- The product is withdrawn from the warranty in case of violation by the consumer of the operating rules set forth in the instruction manual.
- The product is removed from warranty service in the following cases:
- misuse and non-consumer use;
- mechanical damage;
- damage caused by the ingress of foreign objects, substances, liquids, insects;
- damage caused by natural disasters (rain, wind, lightning, etc.), fire, domestic factors (excessive humidity, dust, aggressive environment, etc.)
- damage caused by non-compliance of power and cable network parameters with state standards and other similar factors;
- when operating equipment in the power supply network with a missing single ground loop;
- in case of violation of seals installed on the product;
- lack of serial number of the device, or inability to identify it.
- The warranty does not cover consumables and accessories, as well as filters, shelves, drawers, stands and other containers for storing products.
- The warranty period is 12 months from the date of sale.
- Tear-off maintenance tickets are provided by an authorized service center.
The completeness of the product is checked. I have read the terms of the
warranty service, no complaints.
Customer Signature_
Warranty card
Product information
Product
Model
Serial number
Seller Information
Trade organization name
The address
Date of sale
Seller stamp
Coupon
Seller stamp
Date of application
Cause of damage
Date of completion
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>