ARDEX Finish Coat Smoothing Compound Instructions
- September 2, 2024
- ARDEX
Table of Contents
ARDEX Finish Coat Smoothing Compound
Important Information
Rapid Drying – Install floorcoverings after 20 minutes
Excellent Coverage – Skim coat up to 70m2
Suitable for residential and light commercial areas
No primers or additives required
DESCRIPTION
ARDEX FINE FINISH is a cement based smoothing compound designed to provide a
smooth, permanent finish to a variety of internal substrates prior to the
installation of floorcoverings such as vinyl, carpet and ceramic tile.
ARDEX FINE FINISH allows the installation of most floorcoverings in as little
as 20 minutes over concrete, wood, ceramic and quarry tile, all without the
need for priming or additives. It is suitable for residential and commercial
areas.
ARDEX FINE FINISH mixes with water to provide a smooth, creamy mortar for easy
application. Engineered around a self-drying cement based matrix, all of the
mix water is chemically converted within the product. This unique technology
eliminates flooring installation problems such as debonding, crumbling, mildew
and staining.
SURFACE PREPARATION
Concrete floors must be structurally sound, clean and free of dirt, dust, oil,
curing and sealing compounds and any other surface contaminant which may act
as a bond breaker. Where required, mechanically clean the floor using
recommended preparation methods such as shotblasting, diamond grinding,
shaving or other acceptable methods to a suitable surface.
Acid etching is not an acceptable method of cleaning the subfloor. Do not use
solvents or sweeping compounds.
Subfloor temperatures must be a minimum of 10°C.
MIXING RATIO
Depending on application mix 4.5–5.0 litres of water to 10kg of ARDEX FINE FINISH powder, or by volume; 1 part of water to 2 parts of ARDEX FINE FINISH powder.
MIXING
ARDEX repair products react and harden quickly when mixed with water. Thorough mixing in the shortest possible time is essential to ensure a lump free, slump resistant mortar. Always mix the powder into the water. Mechanical mixing using a mixing paddle and electric drill will produce a creamier, smoother consistency. Do not overwater.
INSTALLATION
ARDEX FINE FINISH is easily applied to any prepared surface using a steel trowel. Apply sufficient pressure to fill all defects and to fine the product into the subfloor surface. It is not necessary to leave a minimum thickness on the substrate. Use the least amount possible to obtain the desired smoothness.
THICKNESS
ARDEX FINE FINISH can be applied from a true fine edge up to 3mm in one application.
POT LIFE
Approximately 20 minutes at 20°C. Pot life will be extended in cooler conditions and shortened in warmer conditions. Mix only the amount that will be used immediately to avoid waste.
INSTALLATION OF FLOORING
As soon as the ARDEX FINE FINISH can be walked on without damaging the surface (approx 20 minutes), floorcoverings such as vinyl, carpet and ceramic tile can be installed. When installing a skim coat of ARDEX FINE FINISH over non-porous surfaces such as ceramic tiles or vinyl, always refer to the adhesive supplier for their recommended installation procedure.
COVERAGE
A 10kg unit will cover 20m2 at 1mm thickness. When skim coating over concrete, coverage is up to 35m2 and over plywood 70m2 can be achieved. Due to the unique formulation of ARDEX FINE FINISH and the varying thickness that this product is applied, both coverage and drying time is difficult to specify and is an estimate only.
EMBOSSING FILLER
To use ARDEX FINE FINISH as embossing filler over existing vinyl, first ensure
the surface is clean and free of waxes or other dressings. The floor must be
well bonded and have been installed over a suitable substrate. Do not use as
embossing filler over a cushioned floor thicker than 2mm or a floor installed
using perimeter bonding.
Combine one part by volume of mixed ARDEX P 82 to one part by volume of ARDEX
FINE FINISH. For example, mix 1 cup (250ml) of ARDEX P 82 (Part A) with 1 cup
(250ml) of ARDEX P 82 (Part B), blend this to a uniform consistency then add
1.5–2 cups (375–500ml) of ARDEX FINE FINISH. Mix to a creamy consistency and
apply to prepared residential sheet vinyl in the thinnest possible layer to
fill the existing pattern.
The embossing filler will typically require 90 minutes of drying time before
installation of the new sheet vinyl. The surface is ready when a twist of a
shoe does not affect the bond of the embossing filler. When dried, the filled
vinyl is considered a non-porous surface and flooring adhesive should be
selected accordingly. Loose lay, or contact the adhesive supplier for specific
recommendations.
SHELF LIFE
ARDEX FINE FINISH has a shelf life of 12 months when stored in the original unopened packaging, in a dry place at 23°C and 50% relative humidity.
SAFETY DATA
This product may cause irritation and an allergic reaction to the skin. It may
cause serious eye injury and irritation to the respiratory system. In case of
contact with the eyes rinse with running water (15 mins) including removal of
contaminated clothing. Wear protective gloves, clothing, eye and face
protection. Avoid inhaling dust/ fume/gas/mist/vapours/spray. Ensure adequate
ventilation during mixing and application. Store locked up. Check with your
local Council regarding the disposal of contents. Keep out of the reach of
children. Call the Poisons Information Centre on 131 126 (AUS) and 0800 764
766 (NZ) or call a doctor if you feel unwell.
Additional information is in the Safety Data Sheet (SDS) at
www.ardexaustralia.com
GUARANTEE
Ardex Australia Pty Ltd (“we” or “us”) guarantees this product (also referred
to as “our goods”) is free from manufacturing defects and will perform to any
applicable specification published by us for 10 years from the date of
application of the product if such application occurs within this product’s
specified shelf life. Our liability under this guarantee is limited at our
option to replacement of the product, repair of any damage to the immediate
surface or area of application of the product, or the cost of such replacement
or repair, in each case if we are satisfied loss or damage was due to a breach
of this guarantee.
This guarantee does not apply if damage or loss is due to failure to follow
our published instructions or any act or circumstance beyond our control,
including shade variations and efflorescence and faulty workmanship on the
part of any installer or applicator of the product.
If you wish to make a claim under this guarantee you must notify us (Address:
7/20 Powers Road Seven Hills NSW 2147; Phone: 1800 224 070; Email:
technicalservices@ardexaustralia.com),
identify the product and provide evidence of your purchase and the subsequent
application of the product within 30 days of any alleged loss or damage
occurring. We reserve the right to ask you for satisfactory evidence of any
alleged loss or damage and to undertake any inspections and tests necessary to
establish your rights under this guarantee. Any claim under this guarantee is
at your cost.
This guarantee is in addition to any rights or remedies you may have as a
“consumer” under the Australian Consumer Law and to that extent you need to be
aware that: “Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss
of damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a
major failure.”
DISCLAIMER
The technical details, recommendations and other information contained in this
data sheet are given in good faith and represent the best of our knowledge and
experience at the time of printing. It is your responsibility to ensure that
our products are used and handled correctly and in accordance with any
applicable Australian Standard, our instructions and recommendations and only
for the uses they are intended. We also reserve the right to update
information without prior notice to you to reflect our ongoing research and
development program. Country specific recommendations, depending on local
standards, codes of practice, building regulations or industry guidelines, may
effect specific installation recommendations.
The supply of our products and services is also subject to certain terms,
warranties and exclusions, which may have already been disclosed to you in
prior dealings or are otherwise available to you on request. You should make
yourself familiar with them.
© ARDEX Australia Pty Ltd 2016.
All aforementioned products are the trade marks of ARDEX Australia Pty Ltd,
its licensors and affiliates.
Customer Support
Kevmor Trade Supplies
11 Belmont Avenue, Belmont WA 6104
Tel: 08 9277 7177
E: sales@kevmor.com.au
W: kevmor.com.au
ARDEX Australia Pty Ltd
Phone: 1300 788 780
Fax: 1300 780 102
Toll Free Technical Services:
1800 224 070 (Australia)
ARDEX New Zealand Ltd
Phone: 0800 227 339
Fax: (03) 384 9779
August 2016
References
- Wholesale Flooring Tools & Installation Supplies | Kevmor
- ARDEX New Zealand - Building Tomorrow
- ARDEX - Tiling, Flooring, Waterproofing & Concrete Repair Systems
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>