SE112-BT1 Shure Bluetooth Earphones User Guide
- June 4, 2024
- Shure
Table of Contents
- SE112-BT1 Shure Bluetooth Earphones
- Wearing the Earphones
- Inserting the Earphones
- Changing Sleeves
- Removing the Earphones
- Choosing a Sleeve
- Cleaning the Nozzle
- Maintenance and Cleaning
- Bluetooth Pairing
- Charging the Earphones
- Using the Remote
- Specifications
- Information to the user
- Environmentally friendly disposal
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SE112-BT1 Shure Bluetooth Earphones
Wearing the Earphones
The following are some suggested ways of wearing earphones.
Inserting the Earphones
Insert the earphones so they form a tight seal. The fit of the earphone can greatly affect sound quality.
Important : If there seems to be a lack of low-frequency response (bass),
this means that the earphone sleeve is not forming a tight seal. Gently push
the earphone deeper into the ear canal or try a different sleeve.
Warning : Do not push the earphone sleeve beyond the ear canal opening.
Changing Sleeves
- Twist and pull to remove the sleeve from the nozzle.
- Slide on a new sleeve so that it completely covers the barb and the nozzle.
Caution: If the barb or any of the nozzle is exposed, the sleeve is not properly installed. Replace sleeves if they do not tightly grip the nozzle. To ensure proper fit and performance, use only sleeves supplied by Shure (unless using custom molded sleeves).
Removing the Earphones
Grasp the body of the earphone and gently twist to remove it.
Note : Do not pull on cable to remove earphones.
Choosing a Sleeve
Soft flex sleeves are included in small, medium, and large sizes. Select an earphone sleeve that provides the best fit and sound isolation. It should be easy to insert, fit comfortably, and easy to remove.
Cleaning the Nozzle
If you notice a change in sound quality, remove the sleeve and check the nozzle of your earphone. If nozzle is blocked, clear obstruction by using wire loop end of cleaning tool.
Warning : The cleaning tool is only to be used to clean the earphones. Any other use, such as using the tool to clean ears, could result in injury.
Maintenance and Cleaning
Careful maintenance ensures a tight seal between the sleeve and nozzle, improving sound quality and product safety.
- Keep the earphones and sleeves as clean and dry as possible.
- To clean sleeves, remove them from earphones, gently rinse in warm water and air dry. Foam sleeves require a longer drying time. Inspect for damage and replace if necessary. Ear sleeves must be completely dry before reusing.
- Wipe the earphones and sleeves with mild antiseptic to avoid infections. Do not use alcohol-based disinfectants.
- Do not expose earphones to extreme temperatures.
- Replace sleeves if they do not fit properly.
- Do not attempt to modify this product. Doing so will void the warranty and could result in personal injury and/or product failure.
Bluetooth Pairing
- Turn off the earphones.
- Press and hold center button on earphone remote until the LED flashes blue and red.
- From your audio source, select “Shure BT1.”
- LED turns blue when successfully paired.
Charging the Earphones
Red LED indicates low battery.
- Connect earphones to charging device using supplied cable.
- LED is red while charging.
- When earphones are charged, LED turns off.
Warning : Before charging, make sure the product is at room temperature,
between 0 to 45°C (32 to 113°F).
Note : Use this product only with an agency-approved power supply that
meets local regulatory requirements (e.g., UL, CSA, VDE, CCC, INMETRO).
Using the Remote
The Center Button
Power on | Press and hold |
---|---|
Power off | Press and hold, 5 seconds |
Pair Bluetooth | Turn off the earphones. Press and hold, 7 seconds |
Play/Pause | Click once |
Answer/End a call | Click once |
Decline a call | Press and hold, 3 seconds |
Activate voice assistant | Phone on, press and hold, 3 seconds |
Factory Reset
| Turn off the earphones and plug into a charger. Press and hold, 15 seconds. Hold past pairing mode until ear phones turn off again.
Up and Down Buttons
Volume Up/Down | Click + or – |
---|---|
Next track | Press and hold +, 3 seconds |
Previous track | Press and hold -, 3 seconds |
Check battery status | Press and hold + and – together, 3 seconds |
Specifications
Bluetooth Specifications
- Antenna Type
- Chip
- Bluetooth 4.1
- Frequency
- 2402 to 2480 MHz
- Modulation Type
- FHSS
- RF Output Power +5.38 dBm (E.I.R.P)
Accessories
For information about earphone accessories and other Shure products visit: http://www.shure.com/americas/products/accessories/earphones Furnished accessories subject to change.
Safety Information
Visit http://www.shure.com/earphones for the latest regulatory and
compliance information.
WARNING
- Follow instructions from manufacturer.
- Product battery may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disassemble, heat above 140°F (60°C), or incinerate.
- Attention should be drawn to the environmental aspects of battery disposal.
- Product shall not be exposed to excessive heat such as sunshine, fire, or the like.
- Do NOT make unauthorized alterations to this product.
Note : Battery replacement to be performed only by Shure authorized service personnel.
CAUTION : Follow applicable laws regarding mobile phone and headphone use
while driving.
This product contains magnetic material. Consult your physician on whether
this might affect your implantable medical device.
Information to the user
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC Part 15.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de la classe B est conforme à la norme NMB-003 du Canada.
Note : Testing is based on the use of supplied and recommended cable
types. The use of other than shielded (screened) cable types may degrade EMC
performance.
The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Shure Incorporated is under license. Other trademarks and trade names are those of their respective owners.
Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances. Paraguay Distributor: Microsystems S.R.L., Senador Long 664 c/Dr. Lilio, Asunción, Paraguay
Certifications
This product meets the Essential Requirements of all relevant European
directives and is eligible for CE marking.
CE Notice: Hereby, Shure Incorporated declares that this product with CE
Marking has been determined to be in compliance with European Union
requirements. The full text of the EU declaration of conformity is available
at the following site: https://www.shure.com/en-EU/support/declarations-of-
conformity.
Authorized European representative: Shure Europe GmbH
Department: Global Compliance Jakob-Dieffenbacher-Str. 12 75031 Eppingen, Germany Phone: +49-7262-92 49 0 Fax: +49-7262-92 49 11 4 Email: EMEAsupport@shure.de
References
- Shure シュア | マイクロホン、インイヤーモニタリング、イヤホンやヘッドホンなどオーディオ機器のリーディングカンパニー
- Earphone Resource Center User Guide - Shure
- Documentation Finder - Shure Europe
- Earphone Resource Center User Guide