Adexa WST5A6WTWL Commercial Mini Countertop Dishwasher Instruction Manual
- June 1, 2024
- Adexa
Table of Contents
Adexa WST5A6WTWL Commercial Mini Countertop Dishwasher
Inner structure and parts name
Dish rack
Control panel
Accessories list
Products Features
- High-temperature wash
- Table dishwasher, easy to install
- Rapid wash, only 29mins
- With fruit wash function (for apple, grape etc.)
Technical data
Safety cautions
- This appliance is not intended for use by persons(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons to avoid a hazard.
CAUTION
- To avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
- The door should not be left in the open position since this could present a tripping hazard.
- This appliance is intended to be used in household and similar applications such as:
- staff kitchen areas in shops, offices and other working environments;
- farmhouses
- by clients in hotels, motels and other residential-type environments;
- At the time of delivery, check the packaging and dishwasher immediately for signs of transport damage. If the appliance is damaged, do not put it into use but contact your supplier or customer service without delay.
- Please dispose of packaging materials properly.
- Site the dishwasher and connect it to the installation instructions.
- The dishwasher must not be connected to the electricity supply while installation is being carried out.
- Ensure that the domestic wiring is properly earthed.
- The mains electricity supply must conform to the details shown on the dishwasher nameplate. Do not connect the dishwasher to the electricity supply via an extension cable.
- During installation, the power supply cord must not be excessively or dangerously bent or flattened. During installation, the dishwasher must only be used by adults for the washing of household dishes.
- This appliance cannot be installed outdoors, not even if the area in which it is installed is covered by a roof; it is also very dangerous to leave it exposed to rain and elements.
- Do not place any heavy objects or water containers, it will influence the dishwasher work or cause damage.
- The water inside the dishwasher is not suitable for drinking. Do not use solvents of any kind inside your dishwasher. They could cause an explosion danger.
- Open the door very carefully if the dishwasher is operating. There is a risk of water squirting out. Do not touch the heating element during or after a wash cycle.
- Fundamental rules to follow when using the appliance:
- Never touch the dishwasher when barefoot or with wet hands or feet;
- We discourage the use of extension cords and multiple sockets;
- If the appliance is not operating properly or maintenance must be performed, disconnect the appliance from the power supply.
- If your family includes children
- The appliance is not intended for use by young children or infirm persons without supervision.
- Young children should be supervised to ensure that they do not play with the appliance.
- Keep detergents out of the reach of children, who must also be kept away from the dishwasher when it is open.
- If a fault occurs
- If the appliance malfunctions, turn off the water supply to the appliance and disconnect the plug from the wall socket. Then, consult the section entitled, “Fault finding”.If you cannot solve the problem, contact a service centre.
- Only specialised personnel are authorised to make repairs.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons to avoid a hazard.
- To maintain the EFFICIENCY and SAFETY of this appliance, we recommend:
- call only the service centres authorised by the manufacturer.
- always use original spare parts.
- When disposing of old appliances
- Appliances that are no longer being used must be made inoperable by cutting the power supply cord and removing the door.
- Take the appliance to a designated waste disposal centre.
Installation guide
Unpacking
- Unpack the external carton, foam pad, and plastic bag
- Unpack the package of the dish rack, meanwhile, take out the accessories
- Put dish rack back properly
- Tips: each appliance was tested before leaving the factory to ensure quality.
- If there is a water drop when you first time use the dishwasher, please be assured of use.
Positioning the appliance
- Positioning the appliance in the desired location. Ensure the height is over 500mm, and leave a distance of over 50mm for four sides.
- The dishwasher is equipped with (a water supply and) drain hoses that can be positioned to the right or the left to facilitate proper installation.
- Keep the appliance away from gas stoves or other heat producers(over 300mm)
- To easily inlet or drain, place this appliance on the cabinet or table.
- Do not place this appliance in the below place:
- The place with direct sunlight
- Frozen place
- Uneven and unstable place
Drainage pipe connection
- Connect the drainage pipe to the outlet and clamp, and the end pipe must not be immersed in water.
- Connect the water inlet pipe and drainage pipe to the dishwasher, see the below picture:
- Fix the drainage pipe on the sink with a suction pad
Electrical Connection
After making sure that the voltage and frequency values for the current in the
home correspond to those on the rating plate and that the electrical system is
correct for the maximum voltage on the rating plate, insert the plug into an
electrical socket that is earthed properly (the earthing of the appliance is a
safety requirement mandated by law). If the electrical socket to which the
appliance must be connected is not appropriate for the plug, replace the whole
cable, rather than using adaptors or the like as they could cause overheating
and burns.
Adding water mode
- Adding water manually
- Open the water tank cover, then add water 4.5 litres.
- Before startup, fill up with water , the appliance will make a “di-di-di” sound.
- After start-up, if the water tank lacks water, “the” icon keeps on until fills up with water, the appliance makes a “di-di-di” sound, and “the” icon turns off.
- Adding water automatically
- Connect the water pipe to the dishwasher, it will add water automatically.
- Make use of the water pressure between 0.03MPa and 1.0MPa if it is over 1.0MPa, will damage the appliance, and if less than 0.03MPa, will influence the appliance’s work.
- User guide
Program Overview
How to place tableware
Before placing the dishes in the dishwasher, remove larger food particles to
prevent the filter from becoming clogged, which results in reduced
performance. If the pots and pans have baked-on food that is extremely hard to
remove, we recommend that they are soaked before being washed. This will
eliminate the need for extra wash cycles. Pull out the rack to load the
dishwasher.
How to use the rack
We recommend that you place the most difficult-to-clean items on the rack:
pots, pans, lids, serving dishes and bowls, as shown in the figure. It is
preferable to place serving dishes and lids on the sides of the racks to avoid
blocking the rotation of the spray arm. Pots, serving bowls, etc. must always
be placed face down.
Silverware should be placed in the silverware basket with the handles at the bottom; if the rack has side baskets, the spoons should be located individually in the appropriate slots. Especially long utensils should be placed in the horizontal position.
The capacity of the rack
WARNING
Knives and other utensils with sharp points must be loaded in the basket with
their points down or placed in a horizontal position.
How to fill the detergent
Detergent specifically intended for use with dishwashers must be used. For the
table dishwasher without a dispenser, the detergent fills into the dishwasher
directly. And must be refilled before the start of each wash cycle.
Not suitable for the dishwasher
- What you should not put into the dishwasher, cutlery and tableware manufactured in whole or part from wood. They become faded and unsightly in appearance. Furthermore, the adhesives that are used are not suitable for the temperature that occurs inside the dishwasher. Delicate decorative glassware and vases, special antique or irreplaceable china.
- The decorative patterns on such items will not be dishwasher-proof.
- Plastic objects that are not resistant to hot water, copper and pewter utensils are also not suitable. Decorative patterns printed or painted onto the surface of crockery, glasses, etc., aluminium and silver items tend to become discoloured or faded if washed in the dishwasher. Some types of glass can become opaque in appearance after they have been washed many times in a dishwasher. Highly absorbent materials, such as sponges and towels, should never be placed in the dishwasher.
Our recommendation
In future, only purchase tableware or kitchenware that has been confirmed as
being dishwasher-proof.
Important
- Dishes or cutlery that have been soiled by tobacco ash, wax, lubricating grease or paint, should not be put in the dishwasher.
- Damage to glassware and other dishes
Possible causes
- Type of glass or manufacturing process
- Chemical composition of detergent
- Water temperature and duration of dishwasher program. Suggested remedy
- Use glassware or porcelain dishes that have been marked “dishwasher-proof ” by the manufacturer.
- Use a mild detergent that is described as “kind to dishes”. If necessary, seek further information from detergent manufacturers.
- Select a program with a low temperature and a short duration as possible.
- To prevent damage, take glass and cutlery out of the dishwasher as soon as possible after the program has ended.
Washing dishes Program selection
The most appropriate program can be identified by comparing the type of
crockery, cutlery, etc., as well as the amount and condition of food that
remains, with the details contained in the wash cycle table.
- The corresponding program sequence, duration and consumption details are shown in the right half of the overview.
- For example: Use the program for dishes and utensils that have plenty of food remaining stuck on hard.
Program data
The stated program data are based on standard operating conditions.
- The values can vary considerably according to different amounts of dishes temperature of mains water supply pressure of mains water supply ambient temperature fluctuations in mains voltage machine-related factors (e.g. temperature, water volume, …)
Switching the dishwasher ON
Closed the door, then Push the “Power” button Press the program to choose the
wash mode, and the screen shows the remaining time of the program. If you
change the program, you can continue to press the “program” button.
- Press the “Start / Pause” button, and the program starts automatically.
End of program
Six beeps will indicate that the wash cycle has finished and then the
dishwasher will be turned off.
Several minutes after the program has ended:
- Open the door.
- Turn the water tap off.
- Remove dishes, etc. when they have cooled down.
Interrupt the program
- Open the door. Caution! There is a risk of water squirting out from inside the appliance. Do not open the door fully until the spray arm has stopped rotating.
- Open the door, Please press the “Start/Pause” button first!
- If the appliance has already heated up or the hot water was switched ON and then the appliance door opened, leave the door ajar for several minutes and then close it.
- Otherwise, the appliance door may open due to expansion.
Cancelling or modifying a cycle
To modify a cycle that is already underway, press the “Power” button, all of
the settings will be cancelled. To set a new cycle, and then press the “Power”
button again to switch on the dishwasher, and press “Program” to choose a new
wash mode. During modifying the cycle, if the detergent has already been used,
and the appliance may have already drained the wash water. If this is the
case, the detergent must be refilled. To cancel one running cycle, press the
“Power” button is ok. How to keep your dishwasher in shape
After Every Wash
After every wash, turn off the water supply to the appliance and leave the
door slightly ajar so that moisture and odours are not trapped inside.
Remove the plug
Before cleaning or performing maintenance, always remove the plug from the
socket. Do not run risks.
No solvents or abrasive cleaning products
To clean the exterior and rubber parts of the dishwasher, do not use solvents
or abrasive cleaning products. Rather, use only a cloth and warm soapy water.
To remove spots or stains from the surface of the interior, use a cloth
dampened with water and a little white vinegar, or a cleaning product made
specifically for dishwashers.
Moving the Appliance
If the appliance must be moved, try to keep it in a vertical position. If
necessary, it can be positioned on its back.
Seals
One of the factors that cause odours to form in the dishwasher is food that
remains trapped in the seals. Periodic cleaning with a damp sponge will
prevent this from occurring. The door should not be left in the open position
since this could present a tripping hazard.
When you go on holiday
When you go on holiday, it is recommended that you run a wash cycle with the
dishwasher empty and then remove the plug from the socket, turn off the water
supply and leave the door of the appliances slightly ajar. This will help the
seals last longer and prevent odours from forming within the appliance.
Care and maintenance
Regular inspection and maintenance of your appliance helps to prevent problems
from occurring. This saves time and aggravation. You should therefore
carefully inspect the inside of your dishwasher from time to time. The overall
condition of the appliance Check that no grease or scale has accumulated on
the inside of the dishwasher. If you discover any deposits: Clean the interior
of the dishwasher thoroughly with a detergent solution.
Filter
Filters 6 and 7 can prevent larger particles of food in the water from
reaching the pump. These particles may occasionally block the filters.
- When the appliance has finished washing, check the filters for particles of food and, if required, clean.
- After undoing the coarse micro-filter 7, filter unit 6 can be removed. Remove any particles of food and rinse the filters under running water.
- Insert the filter unit 6 and tighten the coarse microfilter 7.
Spray arm
Lime and remnants of food in the washing water can block the nozzles in the
spray arms
- Inspect the nozzles for blocked holes due to remnants of food.
- If necessary, pull the lower arm upwards and lift it off.
- Clean the spray arms under running water.
- Refit the spray arms.
Fault finding
Resolving minor problems yourself
Experience has shown that you can resolve most problems that arise during
normal daily usage yourself, without having to call out a service engineer.
Not only does this save costs, but it also means that the appliance is
available for use again that much sooner. The following list of common
occurrences and their remedies should help you identify the causes of most
problems. Problems… …when the appliance is switched on, the appliance does not
start up.
- Fault with fuse in mains electricity supply.
- The plug was not inserted in the wall socket.
- The appliance door is not closed properly.
- The program button has not been pressed.
- The water tap is not turned on.
- Blocked strainer in water intake hose.
- The strainer is situated in the aquastop or supply-hose connection.
Caution
Do not forget that repairs should only be carried out by a qualified
specialist. Improper repairs can lead to considerable equipment damage as well
as danger to the user. …with the appliance itself Error display on the time-
remaining indicator
Water remains inside the appliance after the program has ended
- Blockage or kind in drainage hose.
- The pump is jammed.
- Filters are blocked.
- The program is still running. Wait for the program to end. …during washing
- An unusual amount of foam is creased
- Normal washing-up liquid has been poured into the dishwasher.
- Remove any spilled rinse aid with a cloth as it could otherwise lead to excessive foaming during the next washing cycle.
- The appliance stops suddenly while washing is taking place
- Cut off the electricity supply to the appliance.
- The water supply has been interrupted.
- A knocking sound can be heard while washing is taking place
- A spray arm is knocking against the dishes inside the appliance.
- A rattling sound can be heard while washing is taking place
- The crockery has not been stacked properly inside the appliance.
Knocking sound coming from inlet valves
- This is caused by the way the water pipes have been laid and it does not affect the way the appliance functions. There is no remedy for this.
- Remove any spilled rinse aid with a cloth as it could otherwise lead to excessive foaming during the next washing cycle. ..with the dishes, cutlery, etc.
- Remnants of food are stuck to the dishes, cutlery, etc.
- The dishwasher was not loaded properly. Jets of water could not reach all parts of the dishes, etc.
- Too many items on the rack.
- Items in the rack were touching each other.
- Not enough detergent was added to the dishwasher
- The selected wash program was not intensive enough.
- The rotation of the spray arm was obstructed by dishes, etc.
- Nozzles in the spray arm are blocked by remnants of food.
- Filters are blocked.
- Filters have been incorrectly fitted.
- The waste-water pump is jammed.
Plastic items are discoloured
- Not enough detergent was added to the dishwasher.
- The detergent has insufficient bleaching properties. Use a detergent containing a chemical bleaching agent.
- White stains are left on crockery, glasses have a milky appearance
- Not enough detergent was added to the dispenser compartment.
- Although water is quite hard
- If you used a phosphate-free detergent, try a detergent containing phosphates and compare results.
Dishes, cutlery, etc. have not been dried
- The selected program does not include a drying function
- Items were removed from the dishwasher too soon.
- Tea stains or traces of lipstick have not been completely removed
- The detergent does not have a sufficient bleaching effect,
- The washing temperature was set too low.
- Glasses become clouded and discoloured; the coating cannot be wiped off
- An unsuitable detergent was used.
- Glasses are not dishwasher-proof.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>