SmallRig PT60 Wireless Remote Controller Instruction Manual

SmallRig PT60 Wireless Remote Controller

Product Information

Specifications :

• Model: [Insert Model Number]
• RF Exposure Requirement: General
• Usage: Portable
• Restrictions: None

Product Usage Instructions

1. Safety Precautions:
   Before using the device, please read all safety instructions provided in the user manual.

2. Power On/Off:
   To power on the device, press and hold the power button for 3 seconds. To power off, repeat the same process.

3. Connectivity:
   Ensure the device is within range of the desired connection source. Follow the pairing instructions in the manual to establish a connection.

4. Charging:
   Use the provided charging cable to connect the device to a power source for charging. Allow sufficient time for a full charge before first-time use.

5. Maintenance:
   Keep the device clean and free from dust or debris. Avoid exposing it to extreme temperatures or moisture.

FAQ (Frequently Asked Questions)

• Q: Can the device be used while charging?
  A: Yes, the device can be used while charging. However, it is recommended to allow it to charge fully before extended use.

• Q: How do I reset the device?
  A: To reset the device, locate the reset button (if available) and press it with a paperclip or similar tool. Follow any additional instructions in the manual.

Wireless Remote Controller

PT60

• Thank you for purchasing product.
• Please read this Operating Instruction carefully.
• Please follow the safety warnings.

In the Box

• Tripod x 1
• Remote Control x 1
• Storage Bag x 1
• User Manual x 1
• Operating Instruction x 1
• Guarantee Card x 1

Product Details

Usage Instructions

Operating instructions for stand

1. Lift the handle upward to unlock it, which allows the phone clamp to rotate 360°. Press downward to lock the handle.
2. Loosen the knob to adjust the angle up and down. Tighten the knob after completing the angle adjustment.
3. Extend the four legs outward.
4. Hold the sleeve and pul I it down to the bottom to extend the legs to their maximum angle. Then, place it on a flat surface. Note: Be careful of to pinching your fingers when folding the legs.
5. Extend the telescopic pole to the desired height.
6. Expand the phone clamp, place the phone inside, and clamp it.

Remote Control Operation Instructions

1. Disassembly: Use your fingers to grip the !OP of the remote control and gently pull it outward.
2. Installation: Align the remote control with the storage slot and press inward.
3. Shutter button : Short press for 1 second to take photos and record videos. long press for 3 seconds to power on/off. The indicator light will flash quickly 3 times when powering on/off.
4. Connection pairing: A slow flashing of the indicator light after powering on indicates entering pairing mode. Open the Bluetooth settings on your phone and search for the remote control named “SmallRig PT60” to pair. Once successfully connected, the indicator light will stop flashing.

Remote Control Operation Instructions

1. Extend the legs and rotate the ground spike counterclockwise to remove it.
2. Flip the ground spike over and rotate its head clockwise into the ground spike compartment. After installation, it can be inserted into soft surfaces such as grass or sand, but should not be used on concrete or rocky surfaces.
   

Specifications

Specifications subject to change without prior notice. Please refer to the physical product for the most up- to-date information.

FCC ID:2BC2U- PT60
www.smallrig.com LQ-8275- 18
Made in China

FCC Statement

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
• To assure continued compliance, any changes or modifications not expressly approved by the party.
• Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices).

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>