SmallRig 2BC2U-ST-25 ST-25 Wireless Remote Controller Instruction Manual
- June 1, 2024
- SmallRig
Table of Contents
SmallRig 2BC2U-ST-25 ST-25 Wireless Remote Controller
Product Information
Specifications:
- Model: [Insert Model Number]
- RF Exposure Compliance: General RF exposure requirement met
- Usage: Portable
Product Usage Instructions:
Safety Precautions:
Before using the device, please read the user manual thoroughly to ensure safe usage.
Power On/Off:
To power on the device, press and hold the power button for 3 seconds. To power off, repeat the same steps.
Connectivity
Ensure the device is within the recommended range for optimal connectivity.
Maintenance:
Regularly clean the device with a soft, dry cloth to prevent dust accumulation.
Troubleshooting:
If you encounter any issues, refer to the troubleshooting section in the user manual or contact customer support.
FAQs:
- Q: Is the device safe for portable use?
- A: Yes, the device has been evaluated to meet general RF exposure requirements and can be safely used in portable conditions.
- Q: How do I know if the device is functioning properly?
- A: Check for indicator lights or refer to the user manual for specific operational guidelines.
Thank you for purchasing SmallRig’s product.
- Please read this Operating Instruction carefully.
- Please follow the safety warnings.
In the Box
- Tripod: × 1
- Remote Control: × 1
- Storage Bag: × 1
- USB-C Charging Cable: × 1
- User Manual: × 1
- Operating Instruction: × 1
- Guarantee Card: × 1
Method of use
Selfie Stick
Ps: Be careful not to pinch your fingers when folding the legs.
- Open the phone holder.
- Press “PUSH” at the base and spread the legs to the maximum angle.
- Extend the telescopic pole to the desired height and place it on a flat surface.
- Be careful not to pinch your fingers when folding the legs.
Suction Cup Phone Holder
- Determine the landscape or portrait orientation. The suction cup can rotate 360°.
- When using a phone with magnetic functionality, slide the auxiliary clip to the edge of the suction cup and attach the phone to the suction cup.
- When using a phone without magnetic functionality, remove the auxiliary clip and pull it apart on both sides, then place the phone inside the holder.
Remote Control
- Disassembly: Turn the selfie stick upside down and gently pull the bottom of the remote control outward.
- Installation : Place the top of the remote control into the slot, and then push the bottom in.
Connection
- Press and hold the remote control shutter button for 3 seconds, and the green light will flash to indicate the pairing mode.
- Turn on your phone’s Bluetooth, and search for the remote control named “SmallRing ST-25 Pro”, and pair it.
- A solid green light on the remote control indicates a successful connection.
- Taking Photos : Open your phone’s camera app and press the remote control button to take a photo.
- Turn On/Off : Press and hold for 3 seconds to turn on/off.
- Charging : When the battery level is low, the red indicator light will start to flash. Please charge it promptly.
- When the battery level is low, the red indicator light will start to flash. Please charge it promptly.
- Use the included USB-C charging cable to charge the remote control through the charging port.
Sleep Mode
- If turned on without a paired connection, it will automatically enter sleep mode after 10 minutes, with the indicator light turning off.
- After pairing with the phone, it will automatically enter sleep mode after not taking photos for 10 minutes. If left unused for 30 minutes, it will automatically shut down.
- To wake from sleep mode: While in sleep mode, briefly press the photo button, the photo indicator light will flash, then enter pairing mode.
Specifications
Specifications are subject to change without prior notice. Please refer to the physical product for the most up-to-date information.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly
approved by the party.
Responsible for compliance could void the user’s authority to operate this
equipment. (Example- use only shielded interface cables when connecting to
computer or peripheral devices).
This equipment complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- (1) This device may not cause harmful interference, and
- (2) This device must accept any interference received, including interference that may cause undesired operation
RF warning statement:
The device has been evaluated to meet general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.
LQ-B272-18
FCC ID : 2BC2U-ST-25
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>