SmallRig 3262 Wireless Handwheel Controller User Manual
- June 4, 2024
- SmallRig
Table of Contents
Wireless Handwheel Controller
3262
User Manual
3262 Wireless Handwheel Controller
In order to ensure the safety of users and prevent product damage caused by
improper use, please carefully read the “Important Notes” in this manual
before use, And keep the manual properly for future reference Important Tips
Please read this user manual carefully.
Please do not use it in water. This product does not have the function of
being dustproof or waterproof.
Please avoid strong extrusion or impact on the product.
This product contains a built-in nonremovable lithium battery. It is strictly
prohibited to disassemble the machine without authorization.
There are a few harmful substances in the battery. Please do not discard them
at will. Please recycle the damaged or unused products according to the waste
management method.
Do not disassemble the product or replace the battery. If you suspect that
there is any problem with the product, please contact the purchase platform,
Apply for after-sales treatment.
REC key: 1. Start and stop REC recording; 2. On/off function.
MARK key:1. AB management; 2. Automatic calibration of lens travel.
Up/Down:1. Frequency band adjustment; 2. Motor number adjustment; 3. Turn
pages up and down. SET key:
SET key:1. Press and hold to enter or exit the current option; 2. Click to
activate or confirm the current option.
LOCK key: to prevent misoperation, double click to open/close the lock.
Wheel 1 (K1): finely control the focusing motor.
Indicator light: Red green blue yellow pink white six-color light display.
USB-C interface: Charging and wired communication ports.
Contact interface: Charging and communication ports.
Expansion interface: 1/4 “- 20 thread interface.
Marking ring: replaceable.
Specifications and parameters
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly
approved by the party.
Responsible for compliance could void the user’s authority to operate this
equipment. (Example- use only shielded interface cables when connecting to
computer or peripheral devices).
This equipment complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
RF warning statement:
The device has been evaluated to meet the general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.
IC Warning
This device complies with Part 15 of the FCC Rules [and contains license-
exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s license-exempt RSS standard(s)]. Operation is
subject to the following two conditions: (1)this device may not cause harmful
interference, and (2)this device must accept any interference received,
including interference that may cause undesired operation.
The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B).
This device meets the exemption from the routine evaluation limits in section
2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain
Canadian information on RF exposure and compliance.
This equipment complies with Canadian radiation exposure limits set forth for
an uncontrolled environment.
RF Exposure Statement
The device has been evaluated to meet the general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.
FCC ID: 2AZWI-3262LEQI
IC: 27649-3262LEQI
www.smallrig.com
Made in China
Manufacturer:
Shenzhen Leqi Network Technology Co., Ltd.
Add: Rooms 103, 501, and 601, Building 5, Fenghe Industrial Park, Nos.
1301-50 Guanguang Road, Longhua District Shenzhen, Guangdong, China.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>