SmallRig 3263 Wireless Receiver Motor User Manual
- June 4, 2024
- SmallRig
Table of Contents
3263 Wireless Receiver Motor
User Manual Small
Rig. Big Dream
3263 Wireless Receiver Motor
- In order to ensure the safety of users and prevent product damage caused by improper use, please carefully read the “Important Notes” in this manual before use,And keep the manual properly for future reference
- Important Tips
- Please read this user manual carefully.
- Please do not use it in water. This product does not have the function of dustproof or waterproof.
- Please avoid strong extrusion or impact on the product.
- This product contains a built-in non removable lithium battery. It is strictly prohibited to disassemble the machine without authorization.
- There are a few harmful substances in the battery. Please do not discard them at will. Please recycle the damaged or unused products according to the waste management method.
Up and down keys: 1. Frequency band adjustment; 2. Motor number
adjustment.
REC interface: REC interface of wired control camera.
Interface: power supply port and communication interface.
Battery hanging plate interface: used with battery hanging plate (3777),
compatible with NPF series batteries.
Wireless Receiver Motor| | Screen size| OLED 0.52″
---|---|---|---
Peak torque| 0.5N.m
Input| 1 5V∼ 16.8V
Maximum transmission distatance| ≥ 1 00m
working frequency| 2.4000 ∼ 2.4835 G Hz
Battery input| 7.4V ∼ 8.2V
Fast charging protocol| PD + QC
Tube| Φ 15mm
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly
approved by the party.
Responsible for compliance could void the user’s authority to operate this
equipment. (Example- use only shielded interface cables when connecting to
computer or peripheral devices).
This equipment complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
RF warning statement:
The device has been evaluated to meet the general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.
IC Warning
This device complies with Part 15 of the FCC Rules [and contains license-
exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s license-exempt RSS standard(s)]. Operation is
subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B).
This device meets the exemption from the routine evaluation limits in section
2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain
Canadian information on RF exposure and compliance.
This equipment complies with Canadian radiation exposure limits set forth for
an uncontrolled environment.
RF Exposure Statement
The device has been evaluated to meet general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.
FCC ID: 2AZVV1-3263LE111
IC: 27649-3263LEQI
Manufacturer.
Shenzhen Leqi Network Technology Co., Ltd.
Add Rooms 103, 501, and 601, Building 5, Fenghe Industrial Park,
Nos. 1301-50 Guanguang Road, Longhua District Shenzhen, Guangdong, China.
www.smallrig.com
Made in China
Documents / Resources
|
SmallRig 3263 Wireless Receiver
Motor
[pdf] User Manual
3263LEQI, 2AZWI-3263LEQI, 2AZWI3263LEQI, 3263 Wireless Receiver Motor,
Wireless Receiver Motor
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>