ZALMAN Z3 NEO ATX Mid Tower Gaming Case Instruction Manual
- June 4, 2024
- ZALMAN
Table of Contents
Mid Tower Gaming Case
Instruction Manual
Z3 NEO ATX Mid Tower Gaming Case
※ RAZER CHROMA can be compatible with Z3 NEO through Z-Sync or H/W supported.
※ Product design and specifications may be revised to improve quality and
performance without notice.
Z Developed and designed by ZALMAN in Korea.
This product is protected by ZALMAN’s pending or registered patents.
Precautions
- Read this manual carefully before installing.
- Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
- Wear gloves to prevent accidents when installing the product.
- Severe damage may occur when mounting the system, so do not apply excessive force.
- Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
- Be careful not to block the ventilation hole of the product when using the system.
- Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
- Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
- Do not insert your hand or another object into the product during operation, as this may injure your hand or damage the object.
- Store and use the product out of children’s reach.
- Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
- The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.
Specifications
| Model | Z3 NEO |
|---|---|
| Case Form Factor | ATX Mid-Tower |
| Dimensions | 410 x 210 x 480(H)mm |
| Weight | 6.4kg |
| Case Materials | Plastic, Steel, Tempered Glass |
| Motherboard Support | E-ATX(~280mm) / ATX / mATX / Mini-ITX |
| Maximum VGA Length | 340mm |
| Maximum CPU Cooler Height | 165mm |
| Maximum PSU Length | 160mm |
| PCI Expansion Slots | 7 |
| Drive Bays | 2 x 3.5″ (2 x Combo, 1 x Toolless), 4 x 2.5″ |
Fan Support
| Top| 2 x 120mm / 2 x 140mm
Front| 3 x 120mm / 3 x 140mm
Rear| 1 x 120mm
Bottom| 2 x 120mm
Fan(s) Included
| Front| 1 x 120mm (Non LED / 3Pin), 1 x Addressable RGB LED Bar
Rear| 1 x 120mm (Addressable RGB)
ARGB Controller Included
Radiator Support| Top| 120mm / 240mm
Front| 120mm / 240mm / 280mm / 360mm
Rear| 120mm
I/O Ports| 1 x Headphone, 1 x Mic, 1 x USB 2.0, 2 x USB 3.0, Power
Button, Reset Button, LED Button
Accessories component
I/O Ports
| Part| #| Part| #| Part| #| Part
---|---|---|---|---|---|---|---
⑥| Power Button| ⓑ| HDD / Power LED| ⓒ| Reset Button| ⓓ| USB 3.0 Ports
ⓔ| USB 2.0 Port| ⓕ| Headphone Jack| ⓖ| Microphone Jack| ⓗ| LED Button
※ Caution: Please do not connect ARGB fans more than 8pcs, otherwise it
may cause malfunction.
※ How to control RGB LED
– LED colors & patterns can be changed by pressing the LED Button on I/O
ports.
– Long pressing on the LED Button for 6 seconds, RGB LED will be turned off
after blinking twice in white.
– Long pressing on the LED Button for 3 seconds, RGB will be synchronized with
the motherboard after blinking once in white.
Press the LED Button again to desynchronize with the motherboard.
A ARGB LED 1~4 / 3-Pin
B ARGB LED Control Button / 2-Pin
– Connector to ARGB LED Control Button
C Other Motherboards Sync / 3-Pin
– Connector to Motherboard
– Requires Motherboard that Supports RGB Sync
※ Caution: if Addressable 3 Pin connects to a 12V header instead of a 5V
header improperly, It may cause fatal damages to the product by the
overvoltage.
D SATA Power / 15-Pin
– Connector to PSU
– Input: 5V
E Connect the ARGB connector to the RGB hub
- Removing the side panels
- Removing the front panel
- Mounting the motherboard
3-1. Motherboard size
**** - Mounting the PSU
- Mounting PCI-E(VGA) card
- Mounting the 3.5″ and 2.5″ SSD / HDD
- Mounting the 2.5″ SSD
- Mounting the 2.5” SSD
- Mounting the radiator****
-
Mounting the front radiator
・120mm / 240mm / 280mm / 360mm| 2) Mounting the top radiator
・120mm / 240mm
---|---
| -
Mounting the rear radiator
・120mm
-
Fan(s) Included / Fan Specifications
1 Addressable RGB LED FAN
– FAN : 12V 0.18A
– LED : 5V 0.72A
– Hydraulic Bearing
2 Standard FAN
– FAN : 12V 0.16A
– Sleeve Bearing -
Mounting the fans
-
I/O Connectors
Certification
ROHS,
This mark, designed by Zalman, indicates product compliance with the European
Union’s RoHS
(Restriction of Hazardous Substances) Directive.
Disposal of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate
collection systems) 
COOL INNOVATIONS
www.zalman.com
References
- zalman.com
- ANDPRO.RU - интернет магазин компьютерной и офисной техники с выгодными ценами и доставкой
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>