HORMANN 3056219 Garage Side Sliding Sectional Doors User Guide

June 10, 2024
HORMANN

HORMANN 3056219 Garage Side Sliding Sectional Doors

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
PRODUCT

Product Information

The Garage Side Sliding Sectional Doors are a series 30 type of door leaf. The door leaf is made of sheet steel and is available in Woodgrain, Stucco- textured interior, Deco-, Sand-, Slate-, or Silkgrain finish. The door leaf is operated by an operator which can be either ProMatic or SupraMatic based on the size range of the door. The door comes in both standard and special sizes with glazing S0, S1, or S2. The door sections have a ventilation grille and are available in different heights and widths.

Product Usage Instructions

Before fitting a sectional door, make sure that the door opening is finished and the garage floor is laid and level. Follow the building regulations specific to your country while fitting the door.

To operate the Garage Side Sliding Sectional Door:

  1. Make sure that the door is properly installed and fitted.
  2. Use the operator to open or close the door.
  3. If the operator is ProMatic, it can be used for doors within a specific size range. If the operator is SupraMatic, it is required for doors within a specific size range.
  4. The door sections have ventilation grilles and are available in different heights and widths. Choose the appropriate door section height based on your requirement.
  5. The door sections come with glazing S0, S1, or S2. Choose the appropriate glazing based on your requirement.

Note: Intermediate widths are not possible. Intermediate heights are available in 5mm grids.

Please always take the country-specific building regulations into account! Door leaf constructions and track applications as well as fitting examples are provided in this manual. Before fitting a sectional door, the door opening must be finished and the garage floor must be laid and level.No part may be reproduced without our prior permission. All rights reserved All dimensions in mm are Subject to design changes

Door type

Side sliding sectional door HST – double-skinned steel sections

•   M-ribbed Deco-, Sand-, Silk-, Slate- or Woodgrain| •   Double- skinned, PU-foamed door sections, Deco-, Sand-, Silk- or Woodgrain exterior, Stucco-textured interior

•   Door sections with identical width, vertically ribbed, manufactured from hot-galvanized sheet steel

•   Surface with polyester-primer coating (with Decograin, plastic film coating on the outside)

•   Glazing possible

•   Design elements possible

•   Ventilation grilles possible in the bottom door section

---|---
•   L-ribbed Deco-, Sand-, Silk-, Slate-, Wood- or Duragrain, Planar| • Double-skinned, PU-foamed door sections, Deco-, Sand-, Silk- or Woodgrain exterior, Stucco-textured interior

•   Door sections with identical width, vertically ribbed, manufactured from hot-galvanized sheet steel

•   Surface with polyester-primer coating (with Decograin, plastic film coating on the outside)

•   Glazing possible

•   Design elements possible

•   Ventilation grilles possible in the bottom door section

See brochure for additional details.

Abbreviations used

  • AKS Curve side room
  • ASS Closing side room
  • DRH Lever height
  • ET Distance back
  • EW Drainage
  • LDH Clear passage height
  • LZ Clear frame dimensions
  • N Number of fastenings
  • RM Grid height
  • TH Door section height
  • W Total distance back including operator’s head

Side sliding sectional door HST 42

M-ribbed Woodgrain Actuated by operator

External views
(The dimensions shown correspond to size 2500 × 2125 mm. Deviations may occur with other door sizes.)HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-1

Special sizes

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-2

M-ribbed Deco-, Sand-, Slate- or Silkgrain Actuated by operator

External views
(The dimensions shown correspond to size 2500 × 2125 mm. Deviations may occur with other door sizes.)HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-3

Special sizes

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-4

L-ribbed Woodgrain Actuated by operator

External views
(The dimensions shown correspond to size 2500 × 2125 mm. Deviations may occur with other door sizes.)HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-5

Special sizes

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-6

L-ribbed Woodgrain Manually operated

External views
(The dimensions shown correspond to size 2500 × 2125 mm. Deviations may occur with other door sizes.)

Standard sizes

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-7

Special sizes

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-8

L-ribbed Sand-, Silk-, Slate-, Deco- or Duragrain, Planar Actuated by operator

External views
(The dimensions shown correspond to size 2500 × 2125 mm. Deviations may occur with other door sizes.)

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-9

Standard sizes

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-10

Special sizes

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-11

L-ribbed Sand-, Silk-, Slate-, Deco- or Duragrain, Planar Manually operated

External views
(The dimensions shown correspond to size 2500 × 2125 mm. Deviations may occur with other door sizes.)

Standard sizes

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-12

Special sizes

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-13

Design elements for L-ribbing Version in Deco-, Sand-, Silk-, Slate-, Wood- or Duragrain, Planar

Style arrangements (external views correspond to door size 2500 × 2125 mm) of design elements are possible in each section, other arrangement on request. Number of styles based on technical feasibility.HORMANN-3056219-Garage-Side-
Sliding-Sectional-Doors-FIG-14

Intermediate heights are possible! Number of styles based on technical feasibility:

  • < 2375 mm 3 design elements
  • 2375 mm 4 design elements

Notices:

  • Styles are not possible in the first and last section with intermediate widths.
  • For operator-driven doors with handle, styles are not possible on the handle position.
  • For manually operated doors, styles are not possible on the handle position or underneath the handle.

Glazings for M and L-ribbing
Arrangements (external views correspond to door size 2500 × 2125 mm) of the glazing are possible in each section, other arrangement on request. Number of glazings based on technical feasibility. Glazing clear view 202 × 375 mm. Overall frame dimension 270 × 395 mm.

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-15

Notices:

  • Glazings are not possible in the first and last section with intermediate widths.
  • For operator-driven doors with handle, glazings are not possible on the handle position.
  • For manually operated doors, glazings are not possible on the handle position or underneath the handle.

ES track application, standard sizes Operator wall fitting Manual operation (LZ < 5000)

(The dimensions shown correspond to size 2250 × 2125 mm. Deviations may occur with other door sizes.)

Notice:

  • The clearance for fitting and subsequent operation of the door must be complied with.
  • The threshold is delivered as a separate package.
  • If required, shorten operator boom on site (W ≥ LZ + 1100)HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-FIG-16

C = side bottom guide

C1| 850
C2| 1500
C3 (LZ > 4500)| (ET – 1640 ) / 2 – 250
1-part top frame fixing| Side track

T

---|---
LZ| N
1800 – 2125| 4| 5
2126 – 2625| 5| 6
2626 – 3125| 6| 7
3126 – 3750| 7| 8
3751 – 4250| 8| 9
4251 – 4750| 9| 11
4751 – 5000| 10| 12
2-part top frame fixing|
5001 – 5500| 10| 13
5501 – 6500| 12| 14
Curve angle [a]| Max. AKS
---|---
135°| 458
130°| 497
125°| 531
120°| 561
115°| 587
110°| 612
105°| 635
100°| 657
95°| 697
90°| 700

DS track application, standard sizes Operator wall fitting, small sideroom AKS Manual operation (LZ < 5000)

(The dimensions shown correspond to size 2250 × 2125 mm. Deviations may occur with other door sizes.)

Notice:

  • The clearance for fitting and subsequent operation of the door must be complied with.
  • The threshold is delivered as a separate package.
  • If required, shorten operator boom on site (W ≥ LZ + 1100)HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-FIG-17

Top frame fixing| Side track

T

---|---
LZ| N
1800 – 2125| 5| 6
2126 – 2624| 6| 7
2625 – 3124| 7| 8
3125 – 3999| 8| 10
4000 – 4499| 9| 11
4500 – 4999| 10| 12
5000| 11| 14
2-part top frame fixing|
5001 – 5749| 12| 16
5750 – 6500| 14| 18
C = side bottom guide

C1| 850
C2| 1500
C3 (LZ > 4500)| (ET – 1640) / 2 – 250

ES track application, standard sizes Operator ceiling fitting A

(The dimensions shown correspond to size 2250 × 2125 mm. Deviations may occur with other door sizes.)

Notice:

  • The clearance for fitting and subsequent operation of the door must be complied with.
  • The threshold is delivered as a separate package.
  • If required, shorten operator boom on site (W ≥ LZ + 1100)HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-FIG-19

C = side bottom guide

C1| 850
C2| 1500
C3 (LZ > 4500)| (ET – 1640) / 2 – 250
1-part top frame fixing| Side track

T

---|---
LZ| N
1800 – 2125| 5| 5
2126 – 2624| 6| 6
2625 – 3124| 7| 7
3125 – 3999| 8| 8
4000 – 4499| 9| 9
4500 – 4999| 10| 11
5000| 11| 12
2-part top frame fixing|
5001 – 5749| 12| 13
5750 – 6300| 14| 14

ES track application, standard sizes Operator ceiling fitting B

(The dimensions shown correspond to size 2250 × 2125 mm. Deviations may occur with other door sizes.)
Notice:

  • The clearance for fitting and subsequent operation of the door must be complied with.
  • The threshold is delivered as a separate package.
  • If required, shorten operator boom on site (W ≥ LZ + 1100)HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-FIG-21

C = side bottom guide

C1| 850
C2| 1500
C3 (LZ > 4500)| (ET – 1640) / 2 – 250
1-part top frame fixing| Side track

T

---|---
LZ| N
1800 – 2125| 4| 5
2126 – 2625| 5| 6
2626 – 3125| 6| 7
3126 – 3750| 7| 9
3751 – 4250| 8| 10
4251– 4750| 9| 11
4751 – 5000| 10| 12
2-part top frame fixing

LZ| N
5001 – 5500| 10
5501 – 6300| 12

ES track application, standard sizes Operator ceiling fitting B and wall fitting sliding door

(The dimensions shown correspond to size 2250 × 2125 mm. Deviations may occur with other door sizes.)

Notice:

  • The clearance for fitting and subsequent operation of the door must be complied with.
  • The threshold is delivered as a separate package.
  • If required, shorten operator boom on site (W ≥ LZ + 1100)HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-FIG-22
Ceiling fitting B

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-23

C = side bottom guide

C1| 850
C2| 1500
C3 (LZ > 4500)| (ET – 1640) / 2 – 250
1-part top frame fixing

LZ| N
1800 – 2125| 4
2126 – 2625| 5
2626 – 3125| 6
3126 – 3750| 7
3751 – 4250| 8
4251– 4750| 9
4751 – 5000| 10
Side track

LZ| T
1800 – 2125| 5
2126 – 2625| 6
2626 – 3125| 7
3126 – 3750| 9
3751 – 4250| 10
4251– 4750| 11
4751 – 5000| 12

Details

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-24 HORMANN-3056219-Garage-
Side-Sliding-Sectional-Doors-FIG-25

Fixed elements HST 42

External views

Possible fitting options

Fitting examples

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-28

With corner frame made of aluminium profiles

External views

Size range

Ordering sizes = BRB × BRH

Width × height| DRH from FFL
From         935 × 1800

Up to        1284 × 2500

|

1050

Internal fitting opening inwardsHORMANN-3056219-Garage-Side-Sliding-
Sectional-Doors-FIG-30

External fitting opening outwards

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-31

Clear passage width with 90° leaf opening

With block frame made of aluminium profiles

External views

Size range

Ordering size = RAM

Width × height| DRH from FFL
From         943 × 1800

Up to        1330 × 2500

|

1050

Fitting behind the opening / opening inwards

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-34

Fitting in the opening (opening inwards or outwards)

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-35

Clear passage width with 90° leaf opening

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-36

Double-leaf side doors with block frame made of aluminium profiles

External views

Size range

Ordering size = RAM

Width × height| DRH from FFL
From       1803 × 2020

Up to        2500 × 2400

|

1050

Fitting in the openingHORMANN-3056219-Garage-Side-Sliding-Sectional-
Doors-FIG-38

  • Fitting in the opening, opening inwards or outwards, RH or LH hinged

Notice:

  • The ground must be level or sloped to guarantee smooth opening of the double-leaf side door.
  • Technical inspection required!HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-FIG-39

Fitting arrangements
Fitting in the opening, opening outwards or inwards, right-hand hingedHORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-40

Fitting in the opening, opening outwards or inwards, left-hand hinged

Clear passage width with 90° leaf opening

HORMANN-3056219-Garage-Side-Sliding-Sectional-Doors-
FIG-41

Brand quality for residential and commercial construction

The family-owned company Hörmann offers all important construction components for building and renovating projects from a single source. We manufacture in highlyspecialised factories using state-of-the-art production technologies. Furthermore, our employees work intensively on new products, continual further developments and improvements to details. The results are patents and one- of-a-kind products you can depend on.HORMANN-3056219-Garage-Side-Sliding-
Sectional-Doors-FIG-42

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals