iottie Velox Magnetic Wireless Cooling Charger Pro Dash and Windshield Mount User Manual

: June 11, 2024
: iOttie

Velox™

Magnetic Wireless Cooling Charger Pro Dash & Windshield Mount

User Manual

iottie Velox Magnetic Wireless Cooling Charger Pro Dash
A1

Index

For optimal mounting and charging, please follow the detailed instructions within this manual when using the Velox Pro Dash & Windshield Mount. iOttie is not liable for possible damages due to product misuse.

01 Product Information

At a Glance

Magnetic Mounting Face
CryoFlow Cooling System
Rotating Ball Joint
Telescopic Arm
Pivot Knob
Suction Cup
Lever
Detachable USB-C Cable
Dashboard Pad
12V Power Adapter

CryoFlow Cooling System

iottie Velox Magnetic Wireless Cooling Charger Pro Dash
A4

MagSafe Charging Module
Semiconductor CryoChip
Polycarbonate Fan
Aluminum Heat Sink
Temperature Control System
Precision Magnets
Glass Mounting Face

Device Compatibility

Velox products are designed for use with MagSafe compatible iPhones and MagSafe compatible cases. Compatible devices include the iPhone series 12 and later.

Product Specifications

Item

| Specification
---|---
Total Input|

DC 5V-3A
DC 9V-2A

Wireless Charger Output

| 7.5 W
Cable Length|

5 ft

Mount Length

| 5 in
Width|

2.55 in

Height

| 3.25 in
Weight|

7.03 oz

Power Adapter Specifications

Input	Output

DC 5V-3A
DC 9V-2A
DC 12V-1.5A| 7.5 W

02 Installation

Attaching the Dash Mount

Choose an installation method: dashboard/flat surface (A) or windshield (B).

Option A

Dashboard or Flat Surface Installation

Choose a flat area on the vehicle’s dashboard and wipe any dust or debris from the surface.

*If your vehicle has a leather dashboard we recommend windshield mounting to avoid damaging your dash.

1. Peel off the film on the dashboard pad and evenly press onto the desired installation location. Wait at least 20 minutes before attaching the mount.

*The longer you wait before attaching the mount, the more secure the hold will be.

2. Remove the plastic cover from the suction cup and firmly press the mount onto the dashboard pad.

3. Push down the locking lever to engage suction.

The dashboard pad is mounted with a semipermanent adhesive tape. Once removed, it cannot be re-mounted.

When mounting, it is recommended that the surface and product be above 65°F.

When removing the dashboard pad, please use caution. We recommend removing slowly from the edge to avoid damage.

Option B

Windshield Installation

Choose a location on the windshield and wipe any dust or debris from the surface.

*The dashboard pad should not be used for windshield mounting.

Peel off the protective film on the suction cup and press firmly onto the windshield.
Push down the locking lever to engage suction.

To reuse the suction cup, simply rinse under warm water and let air dry to restore tacky suction.

Connecting to Power

Attach the USB-C cable to the Velox Pro. Then, connect the cable to your vehicle’s USB-C port or auxiliary power outlet via the included 18W adapter.

*The Velox Pro does not have an on/off switch. Once the cable is plugged in and the vehicle is turned on, the mount will stay on.

Adjusting the Mount

The Velox Pro will arrive in the closed position. To extend the telescopic arm, simply pull it outwards. When adjusting the arm for the first time, you may need to use extra force to loosen the internal lubricant.

The telescopic arm extends from 4-7″ and pivots on a 260° arc. To raise and lower the arm, loosen the pivot knob. After adjusting, tighten the knob to secure the arm. You can also adjust the angle of the mounting face by tilting or rotating it.

Mounting Your Phone

Peel off the protective film on the magnetic mounting face. Then simply tap your phone against the mount and the magnets will hold it in place. Charging will begin automatically.

Using the CryoFlow Technology

Once your phone is attached to the Velox Pro Mount, the CryoFlow technology will automatically turn on and begin cooling. You are now ready to start driving.

Operation Warnings

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Warning Statements
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

Radio Frequency Exposure Statement for IC
This equipment complies with IC exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body.

Important Safety Information

This manual contains important safety and operating instructions for the Velox™ Pro Magnetic Wireless Charging Dash & Windshield Mount (VLXWCG204).

Please read all instructions and safety information before using this product. If damage occurs as a result of failure to follow the instructions, the warranty will be voided.

Do not expose to rain, moisture, or snow.
Using an attachment made or sold by anyone other than the manufacturer is not recommended, doing so may result in an increased risk of fire, electric shock, or injury.
Do not operate this magnetic wireless charging mount if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified service person.
Do not disassemble this magnetic wireless charging mount; take it to a qualified service person when service or repair is required. Incorrect reassembly may result in electric shock or fire.
To reduce the risk of electric shock, unplug this car charger before attempting any maintenance or cleaning. Turning off the vehicle controls will not reduce this risk.
Avoid extended exposure to direct sunlight, which may damage the device.
Exposing this product to open flames may cause it to explode.
Do not expose this product to strong magnetic fields.
Use a dry, soft lint-free cloth to clean. Do not use any corrosive cleaner or oil to clean.

*Always obey traffic laws and pay attention to the road. Do not attempt to use this device while driving.

This product complies with the radio interference requirements of the European Community.

This product is designed and manufactured with high quality materials and components, which can be recycled and reused.

The product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop you bought this product.

Designed in New York City. 470 7th Ave, New York, NY 10018. Made in China. U.S. Patent Pending ©2023 iOttie. All rights reserved. iOttie and Velox are registered trademarks owned by iOttie, Inc. John 3:16

Apple, the Apple logo, iPhone, iPod, iPod touch, Mac, macOS, Magsafe and Siri are trademarks of Apple Inc., registered in the U.S. and other countries.

The Velox Pro Magnetic Wireless Charging Dashboard & Windshield Mount is backed by a 2 year warranty.

MagSafe Compatible
Only compatible with MagSafe iPhone series and cases.