VIVO STAND-V101N Single Monitor Desk Mount with Extra Long Arm Instruction Manual
- May 21, 2024
- Vivo
Table of Contents
Single Monitor Desk Mount with Extra Long Arm
SKU: STAND-V101N
Instruction Manual
STAND-V101N Single Monitor Desk Mount with Extra Long Arm
https://vivo-us.com/products/stand-v101n
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
| |
---|---|---
help@vivo-us.com| www.vivo-us.com
Chat live with an agent!| 309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE:
SOME HARDWARE MAY NOT BE USED
TOOLS NEEDED DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Insert Pole Cap (D) into the top of Pole (C).
STEP 2
OPTION A: Clamp Installation
Mount Pole (C) to Clamp (B) using M6x16mm Screws (S-A). Tighten using 4mm
Allen Wrench (T-A). Apply the Rubber Pads (I) to the underside of Clamp (B),
then attach Clamp (B) to the desktop.
OPTION B: Grommet Base Installation
Separate Clamp (B) by removing the screws in back with 4mm Allen Wrench (T-A).
Remove the screw from the top of Clamp Bolt (B1), then remove Clamp Bolt (B1).
Apply Rubber Pads (I) to the bottom of Grommet Base (E). Place Support Plate
(G) onto Clamp Bolt (B1), then insert Clamp Bolt (B1) through the grommet hole
and thread into Pole (C) as shown in the diagram.
STEP 3
Slide Pole Cable Clip (H) and Arm (A) onto Pole (C). Secure Arm (A) to Pole
(C) using 5mm Allen Wrench (T-B).
STEP 4
Attach Arm Cable Clips (F) to Arm (A) as shown.
STEP 5
Insert two screws (M-A or M-B) and M5 Washers (M-C) into the top mounting
holes of the monitor, making sure to leave 3mm of thread exposed. Align screws
in monitor over the slots in the VESA plate. Secure using two more Screws (M-A
or M-B) and M5 Washers (M-C) in the bottom two holes of the monitor. Tighten
all four screws using a Phillips screwdriver.
STEP 6
Adjust the tilt joint using 6mm Allen Wrench (T-C).
STEP 7
Store 5mm Allen Wrench (T-B) and 6mm Allen Wrench (T-C) in Pole Cable Clip (H)
for future adjustments.
STEP 8
Tighten the joints in Arm (A) using 8mm Allen Wrench (T-D) with 19mm Wrench
(T-E) and 6mm Allen Wrench (T-C).
STEP 9
Route cables through Arm Cable Clips (F) and Pole Cable Clips (H).
Love your new VIVO
setup and want to share?
Tag us in your photo! @vivo_us
LAST UPDATED: 06/01/2022
REV3 Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
| 309-278-5303| AVG. RESOLUTION TIME (within office hrs): 5M 4S
---|---|---
| www.vivo-us.com
Chat live with an agent!| AVG. RESOLUTION TIME (within office hrs): < 15 M
| help@vivo-us.com| AVG. RESPONSE TIME (within
office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT:
www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Single Monitor Desk Mount with Extra Long Arm – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>