IPRO S501 Mobile Phone User Guide
- June 5, 2024
- IPRO
Table of Contents
IPRO S501 Mobile Phone
Quick starter guide
Device location diagram To turn on the device, press the switch button for 2-3
seconds.
Battery Charging
Batteries must be charged before they are first used. When charging, the
charger should be close to the power socket and easy to unplug.
Insert card description
This device uses standard Nano-SIM and micro-SIM cards. If you need to replace
or purchase SIM cards, please contact the network operator. Insert the needle
into the small hole on the SIM card tray and pop up the card tray. Please
insert the SIM card as shown in the picture. This will prevent the phone from
being recognized or causing damage to the card slot. In case the phone cannot
be recognized or the card slot is damaged. In order to avoid the cell phone
can not identify or cause damage to the card slot.
Dual Sim dual standby
According to your mood of dual sim dual standby management, work and life are
great. In the setting interface, click SIM card management, select 3G card
slot settings according to needs, and easily switch 3G networks Dual card dual
standby single-channel instructions Your mobile phone adopts the design of
“dual sim dual standby” and the two cards inserted into the phone can’t use
voice services or data services at the same time When one of the cards is on a
call, the other card can’t answer the phone. If someone just dials another
card at the moment, you may hear voice prompts such as”the number you dialed
is not in the service area” The user you dialed can’t be connected
temporarily, please dial later”. When one of the cards is using data services,
the data services of the other card can’t be used. The above situation is a
single channel feature of the mobile
phone, which can significantly reduce power consumption, improve standby time,
and has nothing to do with the network status of operators.
security information
Before using the device, please read all safety information to ensure safe
and correct use. Use of an unapproved or incompatible power supply, charger or
battery that may cause fire, explosion or other hazard. When charging the
device, the power sockets should be installed near the device and easily
accessible. When charging is complete or not, please disconnect the charger
from the device and remove the charging from the power socket If the device is
equipped with a non-removable internal battery, do not replace the battery by
yourself to avoid damaging to battery or device. The battery can only be
replaced by the authorized service center. Please dispose the equipment,
batteries and other accessories according to local regulations and do not
treat them as domestic waste disposal. Batteries may explode if improperly
disposed of. If other types of accessories are used, it may violate the
warranty terms of the device and relevant provisions of the country where the
device is located and may lead to safety accidents. For approved accessories,
please contact the authorized service center. In order to prevent possible
hearing damage, do not use high volume for a long time. Please use the device
in the temperature range of 0 °C-35 °C, and store the device and accessories
in the temperature range of -20 °C-45 °C. When the ambient temperature is too
high or too low, it may cause device failure. Do not expose the device and
batteries to high temperature or heating device, such as sunshine, heater,
microwave oven, oven or water heater. Overheating of the battery may cause an
explosion. ! Do not flash by yourself If the user adds the third-party ROM
system or modifies the system files by cracking, the system maybe unstable and
may bring security risks and threats. IPRO will not be responsible for these
situations
the cell broadcast
Enter the Message menu to view the Broadcast list The purpose of cell broadcasting is to inform mobile phone users of the danger, such as serious threats, child abduction and so on, through some alerts issued by operators,the function is activated by default
FCC Warning
Specific Absorption Rate (SAR) information SAR tests are conducted using standard operating positions accepted by the FCC with the phone transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value, in general, the closer you are to a wireless base station antenna, the lower the power output. Before a new model phone is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the exposure limit established by the FCC, Tests for each phone are performed in positions and locations (e.g. at the ear and worn on the body)as required by the FCC. For body-worn operation, this mobile phone has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal and that positions the hand set a minimum of 1.0cm from the body.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference,
- This device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>