EATON XPD900 Wireless Industrial Controller Instruction Manual
- June 14, 2024
- EATON
Table of Contents
XPD900 Rev.3 (TPCB-3612-01) User Manual
Installation Procedure
FCC ID: IA9XPD900
ISED ID: 1338B-XPD900
XPD900 Wireless Industrial Controller
Document Revision: 1
//rf/radio/products/xpd900/FCC/User_Manual.docx
This document, submitted in confidence, contains proprietary information which
shall not be reproduced or transferred to other documents, disclosed to
others, used for manufacturing or any other purpose without the prior written
permission of Eaton / Cooper Industries (Electrical) Inc.
Copyright 2023 Eaton / Cooper Industries (Electrical) Inc.
All rights reserved.
Revision History
| Revision | Author | Date | Description |
|---|---|---|---|
| 0.1 | Radu Oprea | December 28, 2012 | Initial Draft |
| 1 | M. Bazzarelli | October 3, 2023 | 2023 C2PC Update – Antenna & Portable |
Introduction
The XPD900 transceiver module is not sold separately as a stand-alone device.
The module is a subassembly for use inside Cooper Industries (Electrical) Inc.
host products.
This manual is for the use of Cooper Industries (Electrical) Inc.
professionals to integrate the radio module into host products and maintain
compliance.
Labeling Requirements
The statements provided in sections 2.1 and 2.2 shall be included in the user
manual for a host device containing the XPD900 radio module.
2.1 FCC Part 15 Statement for Class A Devices
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
2.1.1 FCC RF Exposure Statement
For a portable host device include this statement in the manual:
FCC RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
For a mobile host device include this statement in the manual:
FCC RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. In order to avoid the
possibility of exceeding the FCC radio frequency exposure limits, this
equipment should be installed and operated with minimum distance 20 cm (7.9
inches) between the antenna and your body during normal operation. Users must
follow the specific operating instructions for satisfying RF exposure
compliance.
2.2 ISED Statement for Class A Devices
ISED Non-Interference Disclaimer
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This device complies with the Canadian ICES-003 Class A specifications. CAN
ICES003(A) / NMB-003 (A).
2.2.1 ISED RF Exposure Statement
For a portable host device include this statement in the manual:
This equipment complies with ISED RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
For a mobile host device include this statement in the manual:
ISED RF Exposure Statement
This equipment complies with ISED RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20 cm (7.9 inches) between the radiator and any
part of your body. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
2.2.2 RSS-Gen Transmit Antenna Statement
For devices that have a removable antenna include the following statement in
the user manual. Only one removable antenna is listed below for inclusion with
this statement because the other approved antennas are not removable.
RSS-Gen Transmit Antenna Statement
This radio transmitter 1338B-XPD900 has been approved by Innovation, Science
and Economic Development Canada to operate with the antenna types listed
below, with the maximum permissible gain indicated. Antenna types not included
in this list that have a gain greater than the maximum gain indicated for any
type listed are strictly prohibited for use with this device.
Under Innovation, Science and Economic Development regulations, this radio
transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by ISED. To reduce potential radio
interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (e.i.r.p.) is not more than
that necessary for successful communication.
Approved Antenna Types:
| Antenna | Mfg. Part Number | Gain (dBi) | Type |
|---|---|---|---|
| Pulse Larsen | NMO3E900B | ||
| NMOHFMID | 5.4 | 5/8λ over 1/4 λ monopole whip |
NOTE: There are other approved antennas, however they are not included in this statement’s table because they are not removable. See the antenna section for all approved antennas. Only the removable antenna is listed in this table.
RF Exposure Information
This product is intended for mobile and portable installation applications.
3.1 Mobile Applications
In order comply with FCC and ISED RF exposure requirements, installation of
this transmitter system’s antennas for a mobile host device must be performed
in a manner that will provide at least 20 cm of clearance from the antenna to
any user or member of the public.
3.2 Portable Applications
To comply with FCC and ISED RF exposure requirements, installation of this
transmitter system’s antenna in a portable host device must provide the
required minimum user separation distance for each specific certified antenna
that is listed in the “XPD 900 RF Exposure” document.
Certified Antenna
Antennas that are certified for use with the XPD900 Rev.3 (TPCB-3612-01) radio module are listed in the following table.
Antenna Reference| Antenna Mfg.| Mfg. Part Number| Antenna Type| Antenna Gain
(dBi)| Antenna Connector Type| Antenna Trace Design Information
---|---|---|---|---|---|---
Host Product| Host PCB| Host
BOM
1| Pulse Larsen| NMO3E900B NMOHFMID| 5/8A over 1/4 A monopole whip| 5.| SMA
with coaxial 6′ cable.| N/A| N/A| N/A
3| Linx| ANT-916-uSP| 1/4 A monopole| 0.3| SMT
soldered on PCB| TD1141 Rev.4| FPCB- 4053R04| N/A
3| Linx| ANT-916-uSP| 1/4 A monopole| 0.3| SMT
soldered on PCB| TD3100 Rev.4| FPCB- 3875R04| N/A
4| Eaton/Cooper Industries (Electrical) Inc.| ACAB-2683-07| 1/4 A monopole|
3.| Soldered to PTH on PCB| R260 Rev.7| FPCB- 3375R07| 900 MHz Rev. 7
4| Eaton/Cooper Industries (Electrical) Inc.| ACAB-2683-07| 1/4 A monopole|
3.| Soldered to PTH on PCB| R260 Rev.13| FPCB- 3375R13| 900 MHz Rev. 13
4| Eaton/Cooper Industries (Electrical) Inc.| ACAB-2683-07| 1/4 A monopole|
3.| Soldered to PTH on PCB| R270 Rev.3| FPCB- 3958R03| 900 MHz Rev. 3
4| Eaton/Cooper Industries (Electrical) Inc.| ACAB-2683-07| 1/4 A monopole|
3.| Soldered to PTH on PCB| R270 Rev.4| FPCB- 3958R04| 900 MHz Rev. 4
Table 1 Certified Antennas
Company Confidential Cooper Industries (Electrical) Inc.
Documents / Resources
|
EATON XPD900 Wireless Industrial
Controller
[pdf] Instruction Manual
IA9XPD900, IA9XPD900, XPD900, XPD900 Wireless Industrial Controller, Wireless
Industrial Controller, Industrial Controller, Controller
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>