BRAYER BR4002 Steam Iron Instruction Manual

: June 3, 2024
: BRAYER

BRAYER BR4002 Steam Iron

BRAYER BR4002 Steam Iron-fig1

The iron is intended for ironing bedding, clothes and for vertical steaming of fabrics.

DESCRIPTION

BRAYER BR4002 Steam Iron-FIG3

Water spray nozzle
Water inlet lid
Continuous steam supply knob
Burst of steam button
Water spray button
Heating element on/off /automatic switch-off indicator
Handle
Power cord protection
Iron base
Water tank
Iron soleplate
Temperature control knob
Self-clean button «Self- Clean»
Beaker

ATTENTION!
For additional protection it is reasonable to install a residual current device (RCD) with nominal operation current not exceeding 30 mA, to install RCD, contact a specialist.

SAFETY MEASURES AND OPERATION RECOMMENDATIONS

Read the operation instructions carefully before using the iron, after reading keep them for future reference.

Use the unit for its intended purpose only, as it is stated in this manual.
Mishandling the iron can lead to its breakage and cause harm to the user or damage to the user’s property, which is not covered by warranty.
Make sure that the operating voltage of the unit indicated on the label corresponds to your home mains voltage.
The power cord is equipped with a «euro-plug»; insert it into a socket that has a reliable grounding connection.
To avoid fire, do not use adapters for connecting the unit to the mains.
To avoid mains overloading, do not switch on several electrical appliances with high power consumption at the same time.
Do not touch the unit body, the power cord and the power plug with wet hands.
Do not let the power cord be on the ironing board and touch hot surfaces and sharp edges of furniture.
Do not use the unit near heating appliances, heat sources or open flame.
Do not use the unit in proximity to the kitchen sink, in bathrooms, near swimming pools or other containers filled with water.
If the unit is dropped into water, unplug it immediately, and only then you can take the unit out of water. Apply to the authorized service center for testing or repairing the unit.
Do not use the unit in places where aerosols are used or sprayed, and in proximity to highly inflammable liquids, do not use the unit in the places where such liquids are stored.
Do not use the unit outdoors.
It is recommended not to use the unit during lightning storms.
Protect the unit from impacts, falling, vibrations and other mechanical stress.
Do not leave the unit unattended. During breaks in operation, put the iron on the base (in vertical position).
Before plugging the unit in set the temperature control knob to the minimal position and switch the continuous steam supply off.
Always switch off and unplug the iron when you do not use it.
Fill the tank with water additionally cleaned with a domestic filter.
Do not fill the water tank with carbonated water, scented liquids, vinegar, starch solution, descaling reagents, chemical agents etc.
Make sure that the water level in the tank is not above the maximal mark «MAX».
ATTENTION! The surfaces of the iron get hot during operation. Avoid contact of open skin areas with hot surfaces of the iron or outgoing steam to avoid burns.
Never steam clothes directly on a person, always use a clothes hanger or a stand.
Do not use the power cord as a carrying handle for the iron.
Switch the unit off and unplug it after the use or before cleaning.
When unplugging the unit, hold the power plug and carefully remove it from the mains socket, do not pull the power cord, as this can lead to its damage and cause a short circuit.
To avoid electric shock do not immerse the iron, the power cord and the power plug into water or any other liquids.
Before taking the iron away, let it cool down completely and pour out the remaining water.
Clean the unit regularly.
For child safety reasons do not leave polyethylene bags used as packaging unattended.
Attention! Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation!
The unit is not intended for usage by children.
Do not leave children unattended to prevent using the unit as a toy.
Do not allow children to touch the operating surface, the unit body, the power cord or the power plug during operation of the unit.
Be especially careful if children or disabled persons are near the operating unit.
During the unit operation and breaks between operation cycles, place the unit out of reach of children.
The unit is not intended for usage by physically, sensory, psychically or mentally disabled persons (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.
From time to time check the power cord insulation integrity.
If the power cord is damaged, it should be replaced by the manufacturer, a maintenance service or similar qualified personnel to avoid danger.
Do not repair the unit by yourself. Do not disassemble the unit by yourself, if any malfunction is detected, and after the unit was dropped, unplug it and apply to the service center.
To avoid damages, transport the unit in the original package.
Keep the unit in a dry cool place out of reach of children and disabled persons.

THE UNIT IS INTENDED FOR HOUSEHOLD USE ONLY, DO NOT USE THE UNIT FOR COMMERCIAL OR LABORATORY PURPOSES.

BEFORE THE FIRST USE

After the unit’s transportation or storage at negative temperature, unpack it and wait for at least 3 hours before using.

Unpack the iron and remove any packaging materials and advertising stickers.
If there is a protective film on the soleplate (11), remove it.
There may be water residue in the tank (10), as the iron has undergone factory quality control.
Keep the original package.
Read the safety measures and operating recommendations.
Check the delivery set.
Examine the unit for damages, in case of damage do not plug it into the mains.
Make sure that specified specifications of power supply voltage of the unit correspond to the specifications of your mains. When using the unit in the mains with 60 Hz frequency, the unit does not need any additional settings.
Clean the iron body and the soleplate with a soft, slightly damp cloth and then wipe it dry.

WATER SELECTION

Use tap water to fill the water tank (10) of the iron.
Anti-calc function softens water in order to decrease the mineral deposit in the steam chamber, but we recommend to fill the tank with water additionaly cleaned with domestic filters.
If tap water is hard, it is recommended to mix it with distilled water in proportion 1:1. If tap water is too hard, mix it with distilled water in proportion 1:2 or use distilled water only.

FILLING THE WATER TANK

ATTENTION!
Before filling the water tank (10) with water make sure that the iron is switched off and unplugged.

Set the temperature control knob (12) to the position «OFF», and the continuous steam supply knob (3) to the position .
Open the water inlet lid (2).
Pour the water into the water tank using the beaker (14) and then close the lid (2).
Notes:
- do not let water go over the «МАХ» mark when filling the water tank (10);
- if you need to refill the water tank during ironing, switch the iron off and remove the power plug from the mains socket.

IRONING TEMPERATURE

Before using the iron for the first time test the heated iron on a piece of cloth to be sure that the iron soleplate (11) and the water tank (10) are clean.

Before ironing check the recommended ironing temperature indicated on the tag.
If the item label is marked with the symbol , do not iron the item.
If there is no label on the clothes item, but you know the type of fabric, refer to the following table to determine the proper temperature.
This table is only valid for smooth materials.
Fabrics of other types (crimped, raised, etc.) are best ironed at low temperature.
Sort items by ironing temperature first: synthetics with synthetics, wool with wool, cotton with cotton.
The soleplate (11) heats up faster than it cools down, that’s why you should start ironing with synthetics, then increase the temperature and iron silk and wool items. Cotton and linen items should be ironed last.
If an item is made of mixed fabrics, set the lowest ironing temperature. For instance, if an item is made from polyester and cotton, set the ironing temperature for synthetics «•».
If you cannot define the fabric structure, find a place that is inconspicuous while wearing and select the ironing temperature experimentally (always start with the lowest temperature and raise it gradually until you get the desired result).
Corduroy and other fabrics that can become glossy should be ironed backside.

DRY IRONING

Place the iron on the base (9) on a flat and steady surface.
Insert the power plug into the mains socket.
Set the steam supply knob (3) to the position « » (the steam supply is off).
Set the desired ironing temperature by turning the knob (12): «•», «••», «•••» or «MAX», depending on the type of fabric; the indicator (6) will light up.
When the iron soleplate (11) reaches the set temperature, the indicator (6) will go out and you can start ironing.
After you finish ironing, set the temperature control knob (12) to the «OFF» position.
Disconnect the power plug from the mains socket and wait until the iron soleplate (11) cools down completely.
Note: when switching the unit on for the first time, foreign smell can appear. It is normal.

STEAM IRONING

The iron is equipped with anti-drip valve that stops water supply, if the soleplate (11) temperature is too low, it prevents dripping from the soleplate (11) openings.
Steam ironing is possible only if the temperature control knob (12) is set to the steam mode «•••» or «MAX».

Place the iron on its base (9).
Insert the power plug into the mains socket.
Make sure that there is enough water in the water tank (10).
Turn the control knob (12) to set the required ironing temperature in the steam mode «•••» or «MAX», the indicator (6) will light up.
When the temperature of the soleplate (11) reaches the set point, the indicator (6) will go out and you can start ironing.
Set the necessary steam intensity with the continuous steam supply knob (3): steam will be released from the openings of the soleplate (11) only if the iron is in horizontal position. To stop the steam supply, put the iron vertically or set the knob (3) to the position « » (steam supply is off).
After you finish ironing, set the temperature control knob (12) to the position «OFF», and the continuous steam supply knob (3) to the position « » (steam supply is off).
Disconnect the power plug from the mains socket and wait until the iron soleplate (11) cools down completely.
ATTENTION!
If steam is not supplied during the operation, check whether the temperature control knob (12) and the steam supply knob (3) are set properly and whether there is water in the water tank (10).

WATER SPRAY

Make sure that there is enough water in the water tank (10).
Press the water spray button (5) to dampen the fabrics.

BURST OF STEAM

The burst of steam is useful for ironing folds and can be used only in the high temperature ironing mode; set the temperature control knob (12) to the position «•••» or «MAX».
When pressing the burst of steam button (4) steam will go out of the iron soleplate (11) openings intensively.
Note: to avoid water leakage from the soleplate (11) openings, press the burst of steam button (4) with 4-5 sec. intervals.

VERTICAL STEAMING

Vertical steaming of fabrics or interior objects can be performed only in the high temperature ironing mode. Set the temperature control knob (12) to the position «•••» or «MAX»).
Hold the iron vertically at the distance of 5-20 cm from the clothes or interior objects and press the burst of steam button (4) with 4-5 second intervals, steam will be released from the soleplate (11) openings intensively.
ATTENTION!
- To avoid fabric melting, do not touch it with the iron soleplate (11) while steaming.
- Do not steam clothes on a person. Use a clothes hanger or a coat rack.
After you finish ironing, switch the iron off and unplug it, wait until the iron soleplate (11) cools down completely, then open the water inlet lid (2), turn over the iron and drain the remaining water.

STEAM CHAMBER CLEANING

Regularly clean the steam chamber of the iron, especially in the regions with «hard» tap water.
Set the continuous steam supply knob (3) to the position (steam supply is off).
Open the lid (2), fill the tank with water up to the maximal mark «МАХ» and close the lid (2).
Place the iron on its base (9).
Insert the power plug into the mains socket.
Set the temperature control knob (12) to the «MAX» position, the indicator (6) will light up.
When the iron soleplate (11) reaches the set temperature, the indicator (6) will go out and you can start cleaning the steam chamber of the iron.
Remove the power plug from the mains socket.
Hold the iron above the sink horizontally, press and hold down the button (13) «Self -Clean».
Boiling water and steam with scale will be intensively released from the soleplate (11) openings.
Slightly sway the iron back and forth, until all the water leaves the water tank (10).
Place the iron on its base (9) and let the soleplate (11) cool down completely.
After the soleplate (11) cools down, wipe it with a dry cloth.
Before taking the iron away for storage make sure that the water tank (10) is empty, andthe iron soleplate (11) is dry.

CLEANING AND MAINTENANCE

Before cleaning make sure that the iron is switched off and cold and the power plug is not connected to the mains socket.
Wipe the iron body with a slightly damp cloth and then wipe it dry.
You can remove the mineral deposit from the iron soleplate (11) with a cloth soaked in table vinegar.
After removing the mineral deposit polish the soleplate (11) surface with a dry clean cloth.
Do not use abrasives or solvents to clean the iron soleplate (11) and body.
Avoid contact of the iron soleplate (11) with sharp metal objects, as well as with metal buttons, zippers etc.
Do not immerse the iron, the power cord and the power plug into water or any other liquids.

STORAGE

Before taking the iron away for storage drain the remaining water from the water tank (10) and clean the iron.
Set the temperature control knob (12) to the position «OFF» and switch the continuous steam supply knob (3) to the position « » (the steam supply is off).
Wind the power cord around the base (9).
Store the iron vertically in a dry cool place out of reach of children and disabled persons.

DELIVERY SET

Iron – 1 pc.
Beaker – 1 pc.
Instruction manual – 1 pc.

TECHNICAL SPECIFICATIONS

Power supply: 220-240 V, ~ 50/60 Hz
Rated input power: 2400 W
Water tank capacity: 360 ml
Steam release: 140 g/min

RECYCLING

To prevent possible damage to the environment or harm to the health of people by uncontrolled waste disposal, after expiration of the service life of the unit or the batteries (if included), do not discard them with usual household waste, take the unit and the batteries to specialized stations for further recycling.
The waste generated during the disposal of products is subject to mandatory collection and consequent disposal in the prescribed manner.
For further information about recycling of this product apply to a local municipal administration, a household waste disposal service or to the shop where you purchased this product.
The manufacturer reserves the right to change the design, structure and specifications not affecting general operation principles of the unit, without prior notice.