IsYoung P-4 Wireless Controller User Manual
- June 6, 2024
- IsYoung
Table of Contents
Wireless Controller for P4
Getting Started
- Make sure you read this guide, before using the controller.
- Reading this guide will help you learn to use the controller.
- Store this guide safely so that you can use it in the future.
User Manual
Brief Introduction:
- Designed for P4/P4 Pro/P4 Slim
- Vibration function
- Accurate,multi-functional motion control
- Improved ergonomics providing a more comfortable grip
- The 3.5mm stereo headset jack can connect with the headset and microphone, allowing users to receive and transmit audio at the same time.
Registering (pairing) the controller
Bluetooth Connection:
- A data-capable USB cable is required to wired connect the controller to the P4 console for the first time.
- Press and hold the PS button, controller’s LED light bar will flash 3)Once connected successfully, the LED light bar will remain lit, now you can enjoy your controller wired or wirelessly.
After the first paring, hence you can reconnect the controller to the
Console wirelessly via Bluetooth. One P4 console can only support 4 Bluetooth
devices at the same time no matter it’s connected wired or wirelessly.
According to the requirements of shipping lithium batteries by air, if the
voltage of lithium batteries are Over 3.7V, which will be prohibited for
shipment to, Therefore, when controller delivered, maybe not work because of
the power shortage, at this point, please charge for your controller first.
- Firstly turn on the P4 system
- Connect the controller to the P4 system with the USB cable
- Hold the PS button to complete device registration.
USB cable(supplied with the P4 system or included in the package)
LED indication
Led indicators will enter into breathing light mode if the controller is
charging under power off status, and the color is random. The light goes off
when the controller is fully charged.
Different light colors of each controller when several controllers connected
to one Console at the same time: User 1 blue light, User 2 red light, User 3
green light, User 4 pink light.
Stand-by mode: orange light
Charge while playing: blue light
Charge while in stand-by mode: orange light and light goes off when full
charged Controller lose connection: white light
Reset function
When the controller is out of order, which can be reset by poking the reset key with a needle.
Product specification
| Type of battery | lithium battery |
|---|---|
| Battery capacity | 600mAh |
| Full charge time | ≈3 H |
| Operating voltage | USB DC 5V <350mA |
| Dimensions | 170.115*70mm |
| Weight | 0.22kg |
Package contents
(1) Controller —————————————————————–1PCS
(2) 0.8m Charging cable—————————————————–1PCS
(3) User Manual- ————————————————————-1PCS
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
‐‐ Reorient or relocate the receiving antenna.
‐‐ Increase the separation between the equipment and receiver.
‐‐Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
‐‐ Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and(2) this device must accept any interference received,
including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirements.