ALLOY Smart Home Leak Sensor User Guide

Alloy Leak Sensor+
Quick-Start Guide

MEET YOUR ALLOY LEAK SENSOR+

Next-generation 800 series leak sensor with longer battery life.
This product can be operated in any Z-Wave® network with other Z-Wave certified devices from other manufacturers. All mains operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.

1. TAMPER button
2. INCLUSION/ADD button
3. HUMIDITY & TEMPERATURE sensor
4. WALL MOUNTING plate

 INSTALLAT ION

PACKAGING CONTENT

• Alloy Leak Sensor+
• Leak detect probe
• 2 x Dry wall anchors
• 2 x Dry wall screws
•  Safety user manual

1.1. WALLMOUNTING
Drill two holes and screw the Alloy Leak Sensor+ back plate onto the wall. Make sure that it is leveled. The Wall-plate allows for simple, error-free installation.

1. Remove back plate from the Alloy Leak Sensor+ and screw it on the wall
2. Press Alloy Leak Sensor+ on back plate and continue

1.2. POWER UP
Alloy Leak Sensor+ will turn ON when you plug Leak detect probe or sensor wire. Alloy Leak Sensor+ won’t go into sleep state until: included, and mounted on a wall plate.Warning! When Alloy Leak Sensor+ is turned ON, it remains ON until manually included or included through SmartStart, and properly mounted (battery drain).
1.3. INCLUSION/ADDING
Set the Alloy Leak Sensor+ in inclusion/adding mode.
Hold the inclusion/add button for 3 seconds, and the white LED will turn on for 1 second. After that, release the button, wait 3-5 seconds, and he inclusion/adding will start. During inclusion/adding the Alloy Leak Sensor+ will keep flashing blue. When the  inclusion/adding process is complete, green light will flash 5 times in quick success.
SMARTSTART
This device supports SmartStart. The QR code can be found on the Alloy Leak Sensor+, below the lid and on the packaging.
The device will enter SmartStar t if the device is not included in the network after power up. And if the device is not included successfully during 10 seconds, it will enter sleep mode. And then

• 2nd SmartStart time delay approximately 16s
• 3rd SmartStart time delay approximately 32s
• 4th SmartStart time delay approximately 64s
• 5th SmartStart time delay approximately 128s
• 6th SmartStart time delay approximately 256s
• 7th SmartStart time delay approximately 512s

Afterward, the SmartStart mode will be auto running with 512-second interval until the device is successfully included or battery run down.
LOCATION OF THE SECURITY 2 DSK ON THE PRODUCT
On the product, DSK PIN code can be found below the back plate on the bottom of the product. Full Security 2 DSK code can be found on the packaging box.
1.4. EXCLUSION/ REMOVING
Set the Alloy Leak Sensor+ in exclusion/remove mode.
Hold the inclusion/add button for 3 seconds and the white LED will turn on for 1 second. After that, release the button, wait 3-5 seconds, and the exclusion/ removing will start. During exclusion/removing, the Alloy
Leak Sensor+ will turn on its red LED. When the exclusion/removing process is complete, red light will flash 5 times in quick success. 1.5. POWER DOWN
To turn the Alloy Leak Sensor+ OFF, remove the probe or the cable.
1.6. FACTORY RESET
Hold the inclusion button for 7 seconds and Alloy Leak Sensor+ will Factory reset. Alloy Leak Sensor+ will beep and red LED will flash 4 times to indicate the Factory reset was successful. Please use this procedure only when the network’s primary controller is missing or otherwise inoperable.
1.7. PRODUCT IDENTIFICATION
Alloy Leak Sensor+ can be identified using the Indicator Command Class with the Indicator ID 0x50. Alloy Leak Sensor+ will flash green 5 times when identified.
1.8. WAKE-UP
Press the inclusion button once to manually wake-up the device. It will flash yellow for 1 second.
1.9. TAMPER
Alloy Leak Sensor+ will stay awake as long as it’s not mounted, i.e., until the tamper button isn’t pressed. It will beep 5 times every 2 minutes to indicate incorrect installation. When correctly installed, the Alloy Leak Sensor+ will beep once. When the sensor is removed from its mount, it’ll beep 5 times. In both cases, a respective tamper notification will be sent on Z-Wave®. Leak detection is not functional in tamper state.

SPECIFICATIONS

KEY FEATURES

• Leak detection
• Temperature sensor
• Humidity sensor
• Audible and visual LED alarm
• Tamper detection
• Battery detection level
• Z-Wave® Long Range support

COMMAND CLASSES

• Main Endpoint
4.6.3.1 Generic and Specific Device Class| The Notification Sensor Device Type MUST use the following Device Classes:
• GENERIC_TYPE_SENSOR_NOTIFICATION (0x07)
• SPECIFIC_TYPE_NOTIFICATION_SENSOR (0x01)
Supported Command Classes (non-secure)| • Z-Wave Plus® Info V2
• Security S2 V1
• Supervision V1
• Transport Service V2
Supported Command Classes (Secured with the highest granted security level)| • Association Group Info V3
• Association V2
• Battery V1
• Configuration V4
• Device Factory reset Locally V1
• Firmware Update Meta-Data V5
• Indicator V3
• Manufacturer Specific V2
• Multi-Channel Association V3
• Notification V8
• Powerlevel V1
• Version V3
• Wake Up V2
• Sensor Multi-Level V11

CONFIGURATION PARAMETERS

CURRENT CONFIGURATION PARAMETERS| PARAMETER NUMBER| SIZE (BYTE)| AVAILABLE SETTINGS| DEFAULT VALUE
---|---|---|---|---
1. Alarm Duration Time
This configuration value can be used to set the total duration of the audio (buzzer) and visual warning (LED) when flood / water leakage is detected. If this configuration is set to ‘0’, both warnings will be active until water leakage is eliminated. See picture below. Unit: min (minute).| 1| 1| 0 ~ 120| 5
2. Alarm Off Duration Time
This configuration value defines the duration of the OFF interval for the flood warning. See picture below. Unit: s (second).| 2| 1| 5 ~ 120| 60
3. First Alarm On Time Duration This configuration value defines the duration of the first ON interval for the flood warning. See picture below. Unit: s (second).| 3| 1| 10 ~ 120| 60
4. Alarm on Time Duration
This configuration value defines the duration of the subsequent ON intervals for the flood warning. See picture below. Unit: s (second).
Does this Alarm locally and Z-Wave® message? or just locally?
NOTE: This controls only LED and buzzer| 4| 1| 5 ~ 120| 5
CURRENT CONFIGURATION PARAMETERS| PARAMETER NUMBER| SIZE (BYTE)| AVAILABLE SETTINGS| DEFAULT VALUE
---|---|---|---|---
5. Disable Water Leakage Detection
If this configuration value is set to ‘0’, it will disable the flood detection function.| 5| 1| 0,1| 1
6. Disable Audio / Beep Alarm
If this configuration value is set to ‘0’, it will disable the audible buzzer / beeping when flood is detected.| 6| 1| 0,1| 1
7. Disable Visual / LED Alarm
If this configuration value is set to ‘0’, it will disable the visual / LED alarm when a flood is detected.| 7| 1| 0,1| 1
8. Basic Set Level
This configuration value sets the level in the BASIC_SET command sent to nodes in Group 2 when the device detects a flood. [0] – Off, BASIC_SET = 0x00, all nodes associated in Group 2 will be
off. [1…99] – On. BASIC_SET = [Setting Value].
[100] – On, BASIC_SET = 0xFF.| 8| 1| 0 ~ 100| 100
9. Multilevel report frequency
Time interval for sending humidity and temperature report from SHT sensor. Unit minutes Value 0 disables the auto report feature.| 9| 2| 0 ~ 65535| 1440
10. Delay flood notification feature
Delay sending flood notification. Unit s (seconds).Value 0 disables the delay.| 10| 1| 0 ~ 255| 3
---|---|---|---|---
11. Flood alert re-send interval Indicates a time interval for re- sending flood notification. Unit minutes
Value 0 disables the re-send feature..| 11| 1| 1 ~ 255| 10

First 4 parametres combined define the flood warning alarm behavior like this: ASSOCIATIONS
Alloy Leak Sensor+ supports 2 association groups, and each group supports the max of 1 associate node.
Group 1 is a Lifeline Group; all nodes which are associated in this group will receive the messages sent by the Alloy Leak Sensor+ through Lifeline.
Group 2 is a controlling group. All nodes associated in this group will be controlled through the BASIC_SET command by the Alloy Leak Sensor+ when it detects a water leakage event. The Command Class, supported by each association group, is shown in the table below:

COMMAND_CLASS_BATTERY
COMMANDCLASS INDICATOR
COMMAND_CLASSDEVICE RESET_ LOCALLY| NOTIFICATION_REPORT SENSOR_BINARY_REPORT BATTERY_REPORT INDICATORREPORT DEVICE RESETLOCALLY NOTIFICATION
2 (Control)| COMMAND_CLASS_BASIC| BASIC_SET

WATER LEAKAGE REPORT
When Alloy Leak Sensor+ detects a leak, it will automatically send the notification report to nodes associated in the Lifeline.

WAKE UP COMMAND CLASS
Alloy Leak Sensor+ stays in sleep state for the majority of time in order to conserve battery life. The minimum wakeup interval is 20 sec. The maximum wakeup interval is 86400 sec (24 Hours). Allowable min step among each wake-up interval is 60 seconds, such as 1860 sec, 1920 sec,1980 sec…
NOTE
The default value is 1 hour with factory default. Higher value means longer battery life. Alloy Leak Sensor+ won’t go in sleep state until: included, mounted on a wall plate, and in flood.

BATTERY COMMAND CLASS
The users can also inquire about the battery status of the Alloy Leak Sensor+ by sending the BATTERY GET command. Once the Alloy Leak Sensor+ receives the command, it will return the BATTERY REPORT command. The Alloy Leak Sensor+ will send BATTERY REPORT = 0xFF command to the Z-Wave® Controller to inform that the Alloy Leak Sensor+ is in dead battery status, the otherwise BATTERY REPORT value range is from 0% to 100%. When the Alloy Leak Sensor+ is powered on, the LED will flash twice, indicating the battery level:
Green – 3V, Blue – 3V – 2.8V, Red – 2.7V – dead battery
SECURITY KEYS

LED INDICATOR

Two 1s flashes

Inclusion/add success| Green| Flash 6 times at 500 ms intervals
Battery full (on device power on)| Two 1s flashes
Wake up| Yellow| Flash 500 ms once
Exclusion/ removing| Red| Flash 1s
Exclusion/ removing success| Five 500ms flashes
Battery low (on device power on)| Two 1s flashes
Factory reset| 4 flashes
Inclusion/ exclusion| White| Flash 1s

SAFETY

• Read, keep and follow these instructions.
• Do not install the Alloy Leak Sensor+ near any water vapor or smoke.
• Do not submerge the Alloy Leak Sensor+ or the Leak detect probe in water.
•  Do not attempt to replace the battery, it can be replaced only by a certified installer.
• Do not open the Alloy Leak Sensor+.
• Keep away from children.
• Do not expose to open flame – flammable product.
• Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.

DISPOSING AND RECYCLINGYOUR PRODUCT

(Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste. To prevent possible harm to the environment or human health from uncont rolled was tedisposal, please separ ate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contac t their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal. (Applicable in countries with separate collection systems)
At Alloy Home, we understand and are committed to reducing any impact our operations and products may have on the environment. To minimize this impact Alloy Home designs and builds its products to be as environmentally friendly as possible, by using recyclable, low toxic materials in both products and packaging.
(Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste. To prevent possible harm to the env ir onment or human health from uncont rolled was tedisposal, please separ ate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contac t their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal. (Applicable in countries with separate collection systems)
At Alloy Home, we understand and are committed to reducing any impact our operations and products may have on the environment. To minimize this impact Alloy Home designs and builds its products to be as environmentally friendly as possible, by using recyclable, low toxic materials in both products and packaging.
Disclaimer
Some content and services accessible through this device be long to thir dparties and are protected by copyright, patent, trademark and/or other intellectual property laws. Such content and services are provided solely for your personal non-commercial use. You may not use any content or services in a manner that has not been authorised by the content owner or service provider.
Without limiting the foregoing, unless expressly authorised by the applicable content owner or ser vice provider, you may not modif y, copy, republish, upload, post, transmit, translate, sell, create derivative works, exploit, or distribute in any manner or medium any content or services displayed through this device.

 ONE (1) YEAR LIMITED WARRANTY

Alloy Home, LLC warrants this product (the “Product”) against defects in materials and/or workmanship under normal use for a period of ONE (1) YEAR from the date of purchase by the original purchaser (“Warranty Period”). If a defect arises and a valid claim is received within the Warranty Period, then as your sole remedy (and Alloy Home’ sole liability), Alloy Home will at its option either 1) repair the defect at no charge, using new or refurbished replacement parts, or 2) replace the Produc twith a new p roduct that is functionallye quivalent to the original, in each case within 30 days following receipt of the returned Product. A replacement product or part assumes the remaining warranty of the original Product. When a Product or part is exchanged, any replacement item becomes your property and the replaced Product or part becomes Alloy Home’ property. Obtaining Service: To obtain warranty service, visit https://smartrent.com/contact-support. Please be prepared to describe the Product that needs service and the nature of the problem. Any claim under this Limited Warranty must be submitted to Alloy Home before the end of the warranty period. Exclusions: This warranty does not apply to a) damage caused by failure to follow instructions relating to the Product’s use or the installation of components; b) damage caused by accident, abuse, misuse, transport, neglect, fire, floods, earthquake or other external causes; c) damage caused by service performed by anyone who is not an authorized representative of Alloy Home; d) accessories used in conjunction with a covered Product; e) a Product or part that has been modified to alter functionality or capability; f) items intended to be periodically replaced by the purchaser during the normal life of the Product, including, without limitation, batteries, bulbs or cables; g) a Product that is used commercially or for a commercial purpose, in each case as determined by Alloy Home.
EXCEPT FOR BODILY INJURY, ALLOY HOME SHALL NOT BE LIABLE FOR (|) ANY LOST PROFITS, COST OF PROCUREMENT OF SUBSTITUTE PRODUCTS, OR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR (II) ANY AMOUNTS IN EXCESS OF THE PURCHASE PRICE FOR THE PRODUCT, IN EACH CASE WHETHER RESULTING FROM THE USE OF OR INABILITY TO USE THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, EVEN IF COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU. TO THE EXTENT PERMITTED BY APPLICABLE LAW, ALLOY HOME DISCLAIMS ANY AND ALL STATUTORY OR IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND WARRANTIES AGAINST HIDDEN OR LATENT DEFECTS. IF ALLOY HOME CANNOT LAWFULLY DISCLAIM STATUTORY OR IMPLIED WARRANTIES, THEN TO THE EXTENT PERMITTED BY LAW, ALL SUCH WARRANTIES SHALL BE LIMITED IN DURATION TO THE WARRANTY PERIOD. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
This warranty gives you specific legal rights and you may also have other rights, which vary from country to country. To exercise your rights under this warranty, please follow the instructions above under the heading “Obtaining Service”, or contact Alloy Home, LLC, 8665 E. Hartford Drive, Suite 200, Scottsdale, AZ 85255. Alloy Home Hub is a registered trademark of Alloy Home, LLC
Manufacturer / Importer:
8665 E. Hartford Drive, Suite 200, Scottsdale, AZ 85255

DECLARATION OF CONFORMITY

We, Alloy Home, LLC, 8665 E. Hartford Drive, Suite 200, Scottsdale, AZ 85255, declare that the product Alloy Home Hub is in compliance with all the technical regulations applicable to the product within the scope of Council Directives 2014/53/EU.
Manufacturer’s Name: Alloy Home, LLC
Address: 8665 E. Hartford Drive, Suite 200, Scottsdale, AZ 85255 Product name: Alloy Leak Sensor+
Operating Temperature: -10° C to 35° C
This device in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. All essential radio test suites have been carried out.

1. CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
2.  The product shall only be connected to a USB inter face of version USB 2.0
3.  Adapter shall be installed near the equipment and shall be easily accessible.
4.  The plug considered as disconnect device of an adapter.
5.  The device complies with RF specifications when the device used at 0mm from your body.
   RF output power: This product can be used across EU member states.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Par t 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inter ference to radio communications. However, there is no guarantee that inter ference will not occur in a particular installation. If this equipment does cause harmful inter ference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter ference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer oran experienced radio/TV technician for help. Tomaintain compliance with FCC’s RF Exposure guidelines, this equipment should be installed and operated at distance greater than 20 cm from your body. Use only the supplied antenna.

FCC ID: 2AAU7-ALSP
IC: 11391A-ALSP
IC Caution
RSS-Gen Issue 5 April 2018”&”CNR-Gen 5e April 2018:
This device complies with Industry Canada licenceexempt RSS standard(s). Operation is subject to the  ollowing two conditions:

1. This device may not cause inter ference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

make your home smart

References

• Browse our catalog of help articles and more | SmartRent Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>