VIVO PP-DK24B Steel Clamp on Desk Pegboard Instruction Manual
- June 15, 2024
- Vivo
Table of Contents
VIVO PP-DK24B Steel Clamp on Desk Pegboard
Product Information
Specifications:
- Product Name: Black Clamp-on Desk Back Panel & Accessory Holder
- SKU: PP-DK24B
Package Contents:
- A (x4) Peg Board
- B (x2) Lower Pole
- C (x2) Upper Pole
- D (x2) Connecting Bracket
- E (x2) Clamp Brace
- F (x2) Clamp
- G (x2) Shelf
- H (x2) Pole Cap
- I (x2) Pad
- K (x2) Straight Hook
- L (x2) Square Edge Hook
- M (x8) Magnet
- N (x2) Clip
- J (x4) Shelf Hook
- S-A (x4) M6x16mm Screw
- S-B (x4) M6x8mm Screw
- T-A (x2) 4mm Allen Wrench
- T-B (x8) Ziptie
Tools Needed:
- Phillips Screwdriver
Product Usage Instructions
Assembly Options:
Above Mounting Single Panel Assembly
STEP 1: Connect Lower Pole (B) and Pad (I) to Clamp Brace (E) using M6x16mm Screws (S-A) and 4mm Allen Wrench (T-A). Secure Clamp (F) to Clamp Brace (E) using M6x8mm Screws (S-B) and 4mm Allen Wrench (T-A).
STEP 2a: Single Panel Assembly
- Choose horizontal or vertical installation orientation and connect Peg Board (A) and Connecting Bracket (D) to front of Lower Pole (B) using M6x25mm Screws (S-C), M6 Washers (S-D), and 4mm Allen Wrench (T-A).
- Place Pole Cap (H) on top of Lower Pole (B).
Above Mounting Double Panel Assembly
STEP 1: Connect Lower Pole (B) and Pad (I) to Clamp Brace (E) using M6x16mm Screws (S-A) and 4mm Allen Wrench (T-A). Secure Clamp (F) to Clamp Brace (E) using M6x8mm Screws (S-B) and 4mm Allen Wrench (T-A).
STEP 2b:
- Choose horizontal or vertical installation orientation and connect Peg Board (A) and Connecting Bracket (D) to Lower Pole (B) using M6x25mm Screws (S-C), M6 Washers (S-D), and 4mm Allen Wrench (T-A).
- Slide Upper Pole (C) into Connecting Bracket (D).
- Connect Upper Pole (C) to Peg Board (A) and Connecting Bracket (D) using M6x25mm Screws (S-C), M6 Washers (S-D), and 4mm Allen Wrench (T-A).
- Connect second Peg Board (A) to Upper Pole (C) using M6x25mm Screws (S-C), M6 Washers (S-D), and 4mm Allen Wrench (T-A).
- Attach Pole Cap (H) to top of Upper Pole (C).
Above & Under Mounting Double Panel Assembly
STEP 1: Connect Lower Pole (B) and Pad (I) to Clamp Brace (E) using M6x16mm Screws (S-A) and 4mm Allen Wrench (T-A). Secure Clamp (F) to Clamp Brace (E) using M6x8mm Screws (S-B) and 4mm Allen Wrench (T-A).
Under Desk Cable Management
Single Panel Assembly
STEP 1: Connect Lower Pole (B) and Pad (I) to Clamp Brace (E) using M6x16mm Screws (S-A) and 4mm Allen Wrench (T-A). Secure Clamp (F) to Clamp Brace (E) using M6x8mm Screws (S-B) and 4mm Allen Wrench (T-A).
STEP 2: Choose horizontal or vertical installation orientation and connect Peg Board (A) and Connecting Bracket (D) to front of Lower Pole (B) using M6x25mm Screws (S-C), M6 Washers (S-D), and 4mm Allen Wrench (T-A). Place Pole Cap (H) on top of Lower Pole (B).
Double Panel Assembly
STEP 1: Connect Lower Pole (B) and Pad (I) to Clamp Brace (E) using M6x16mm Screws (S-A) and 4mm Allen Wrench (T-A). Secure Clamp (F) to Clamp Brace (E) using M6x8mm Screws (S-B) and 4mm Allen Wrench (T-A).
STEP 2: Choose horizontal or vertical installation orientation and
connect Peg Board (A) and Connecting Bracket (D) to Lower Pole (B) using
M6x25mm Screws (S-C), M6 Washers (S-D), and 4mm Allen
Wrench (T-A). Slide Upper Pole (C) into Connecting Bracket (D). Connect Upper
Pole (C) to Peg Board (A) and Connecting Bracket (D) using M6x25mm Screws
(S-C), M6 Washers (S-D), and 4mm Allen Wrench (T-A). Connect second Peg Board
(A) to Upper Pole (C) using M6x25mm Screws (S-C), M6 Washers (S-D), and 4mm
Allen Wrench (T-A). Attach Pole Cap (H) to top of Upper Pole (C).
Accessory Placement
All Assembly Options: Use the provided hooks, shelves, magnets, and clips
to customize the placement of your accessories on the peg board.
FAQ
Q: What is the SKU of this product?
A: The SKU of this product is PP-DK24B.
Q: Where can I find helpful videos and specifications related to this
product?
A: You can scan the QR code with your mobile device or visit the link
https://vivo-us.com/products/pp-dk12b for helpful videos and specifications.
Q: What are the contact details for customer support?
A: You can get in touch with our customer support team Monday-Friday from
7:00am-7:00pm CST:
- Email: help@vivo-us.com
- Website: www.vivo-us.com
- Phone: 309-278-5303
- Live chat: Chat live with an agent on our website.
Q: Is this product safe for children?
A: No, this product contains small parts and is not suitable for children
under 3 years. Adult supervision is required.
Black Clamp-on Desk Back Panel & Accessory Holder (x2)
Instruction Manual
SKU: PP-DK24B
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
https://vivo-us.com/products/pp-dk12b
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com
www.vivo-us.com Chat live with an agent!
309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
TOOLS NEEDED
ASSEMBLY OPTIONS
-
Above Mounting
Single Panel Assembly (pg 3-4) Double Panel Assembly (pg 3, 5-6) -
Above & Under Mounting
Double Panel Assembly (pg 7) -
Under Desk Cable Management
Single Panel Assembly (pg 8-9 Double Panel Assembly (pg 8-9) -
Accessory Placement
All Assembly Options (pg 8-9)
Above Mounting Only
STEP 1
Connect Lower Pole (B) and Pad (I) to Clamp Brace (E) using M6x16mm Screws (S-A) and 4mm Allen Wrench (T-A). Secure Clamp (F) to Clamp Brace (E) using M6x8mm Screws (S-B) and 4mm Allen Wrench (T-A). NOTE: Make sure the pegboard holes are facing forward as shown below.
STEP 2a: Single Panel Assembly
Choose horizontal or vertical installation orientation and connect Peg Board
(A) and Connecting Bracket (D) to front of Lower Pole (B) using M6x25mm Screws
(S-C), M6 Washers (S-D) and 4mm Allen Wrench (T-A). Place Pole Cap (H) on top
of Lower Pole (B).
NOTE: Use the top hole on the Connecting Bracket (D). The bottom hole will not be used
STEP 2b: Double Panel Assembly
Choose horizontal or vertical installation orientation and connect Peg Board
(A) and Connecting Bracket (D) to Lower Pole (B) using M6x25mm Screws (S-C),
M6 Washers (S-D), and 4mm Allen Wrench (T-A).
Note: Use bottom hole of Connecting Bracket (D).
-
HORIZONTAL ORIENTATION
-
VERTICAL ORIENTATION
-
HORIZONTAL ORIENTATION
Slide Upper Pole (C) into Connecting Bracket (D). -
VERTICAL ORIENTATION
Connect Upper Pole (C) to Peg Board (A) and Connecting Bracket (D) using M6x25mm Screws (S-C), M6 Washers (S-D) and 4mm Allen Wrench (T-A).
Connect second Peg Board (A) to Upper Pole (C) using M6x25mm Screws (S-C), M6 Washers (S-D), and 4mm Allen Wrench (T-A). Attach Pole Cap (H) to top of Upper Pole (C).
- HORIZONTAL ORIENTATION
- VERTICAL ORIENTATION
Above & Below Mounting
STEP 1
Connect Lower Pole (B) and Pad (I) to Clamp Brace (E) using M6x16mm Screws (S-A) and 4mm Allen Wrench (T-A). Secure Clamp (F) to Clamp Brace (E) using M6x8mm Screws (S-B) and 4mm Allen Wrench (T-A).
NOTE: Make sure the pegboard holes are facing forward as shown below.
STEP 2
Connect Peg Board (A) and Connecting Bracket (D) to Lower Pole (B) using
M6x25mm Screws (S-C), M6 Washers (S-D) and 4mm Allen Wrench (T-A). Attach
other Peg Board (A) to back of Clamp Brace (E) using M6x5mm Screws (S-E) and a
Phillips screwdriver. Place Pole Cap (H) on top of Lower Pole (B).
NOTE: Use the top hole on the Connecting Bracket (D). The bottom hole will not be used
Under Desk Cable Management
STEP 1
Secure Clamp (F) and Pad (I) to Clamp Brace (E) using M6x8mm Screws (S-B)
and 4mm Allen Wrench (T-A).
STEP 2a: Single Panel
Connect Peg Board (A) to front of Clamp Brace (E) using M6x5mm Screws (S-E)
and a Phillips screwdriver. Use provided Zip Ties (T-B) for managing under
desk cables.
STEP 2b: Double Panel
Connect Peg Boards (A) to front of Clamp Brace (E) using M6x5mm Screws (S-E)
and a Phillips screwdriver. Use provided Zip Ties (T-B) for managing under
desk cables.
ACCESSORY PLACEMENT
Note: Accessories can be placed and used as desired. The following steps shows one way to mount/install accessories and uses the double panel horizontal assembly as an example.
Shelf Mounting
Place Shelf Hooks (J) at desired height on Peg Board (A) and then place
Shelf (G) on Hooks so that magnets on edge make contact with Peg Board (A).
Straight & Square Hooks
Place Straight Hook (K) and Square Hook (L) as desired on Peg Board (A).
Clip & Magnets
Place Magnets (M), and Clip (N) as desired on assembly.
Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
LAST UPDATED: 07/25/2022 REV1
Open Monday – Friday 7:00am – 7:00pm CST,our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within office hrs): < 15 M
AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Clamp-on Desk Privacy Panel – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>