TokeShimi 2B0BBV1S31J 20×28 Inch Backlit LED Bathroom Vanity Mirror Instruction Manual
- June 15, 2024
- TokeShimi
Table of Contents
2B0BBV1S31J 20×28 Inch Backlit
LED Bathroom Vanity Mirror
Instruction Manual
2B0BBV1S31J 20×28 Inch Backlit LED Bathroom Vanity Mirror
Installation
Instruction
CONTACT US
Note: After opening the package, Please inspect the product immediately for
damage in transit or missing parts. If there is any help missing, Please
contact us by (aftersale@tokeshimi-home.com). – or you can contact us at Amazon by following these steps:
– Open “Orders” at Amazon
– Find the product you have purchased and open the product page
– Click Sold by “TokeShimi” -Click”Ask a question”
– Click “An order I have placed”
– Click “Your product” -Click “Other” -Click “Troubleshooting” Then you can
send us messages, we will reply within 24 hours.
PACKING LIST
INSTALLATION TOOLS
PRODUCT DESCRIPTOIN
PRODUCT STYLE
Mounting Method
The mirror can be mounted either Horizontally or Vertically, so there are 8
mounting points on the back of mirror. Please confirm the wall mount
Horizontally or Vertically before installation.
Vertically
Vertically hanging: Please measure the mounting points of “A 1” and “A2”; and the mounting points of “A3″and “A4”
Horizontally
Horizontally hanging: Please measure the mounting points of “B1” and “B2”; and the mounting points of “B3″and “B4”
INSTALLATION OF LED MIRROR
Open the carton and make sure all the parts listed below are present.
Note: Please don’t remove the silicone corner protector before completing the installation.
Mounting point measurement
Measure the distance of four hooks centre and use the level ruler to draw a
horizontal line on the wall and then mark the location of the center of hooks.
Drill pilot holes on the marked spots
Use a electric drill to punch four 6mm holes at the marked spots, and then
apply wall anchors with hammer.
(6mm drill bit, drilling depth in 5 cm)
Insert the screw
Use a screwdriver to screw the screws into the wall anchors. Leave a distance
of 7 mm from the wall.
Connect the power
There are three power wires behind the mirror, including the live wire
(black), the neutral wire (white) and the ground wire (green). You can connect
the wires to standard switched lighting circuit or plug. If you want to
connect power wires to plug, you can refer to the steps:
- Remove the plug cover.
- Unscrew the screws on each of the plug’s pins.
- Insert the twisted copper wires into the holes in the pins.
- Tighten the little screw on each of the plug’s pins.
- Make sure the wire is tightly clamped by the brake or clip.
- Replace the cover of the plug.
Other power connection methods are on the same principle.
Mount the mirror on the wall and ensure it is sturdy
Note: After the installation is completed, please remove the silicone corner protector.
USE AND CLEANING INSTRUCTION
In order to keep the LED mirror look perfectly, we suggest using and cleaning the mirror regularly.
- Please use in safe voltage range. (100V-240V)
- Use electrical tape to wrap around the wires to prevent leakage.
- Do not strike mirror glass with hard or pointed items.
Please obey the following procedure when you clean the mirror.
- It is recommended that the product is cleaned with a soft, non abrasive cloth.
- Do not use Irritating cleaning agents or abrasive materials on any type of finished surface. Please use the any following cleanser to remove the dirt.
Gentle liquid detergent.
Colorless cleanser.
Product Warranty
Manufacturer warranty for 1 year from date of purchase.
If you have any problem, please feel free to contact us on
aftersale@tokeshimi-home.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>