TokeShimi JG-01 Bathroom LED Medicine Cabinet Mirror Instruction Manual
- June 17, 2024
- TokeShimi
Table of Contents
TokeShimi JG-01 Bathroom LED Medicine Cabinet Mirror
HOW TO USE AND CLEAN
In order to keep the LED mirror in perfect condition, we suggest proper use and regular cleaning.
How to Use
- Please ensure that the product is used within the safe voltage range of 100V-120V.
- Please wrap electrical tape around the wires to prevent electrical leakage.
- Avoid using hard or pointed items to strike the mirror glass so as to prevent damage.
How to Clean
When cleaning the mirror, please follow these steps:
- Use a soft, non-abrasive cloth to clean the mirror. Avoid using rough or abrasive materials that may damage the surface.
- Do not use any cleaning agents that may cause irritation or damage to the mirror’s finish. Instead, use any of the recommended cleansers to remove dirt and grime.
Gentle liquid detergent. lY’J Colorless cleanser.
Warranty
A one-year warranty from the date of your purchase.
CONTACT US
After opening the package, please inspect the product immediately and see if there is any damage or missing parts. If there is, please feel free to contact us by aftersale@tokeshimi-home.com or find us at Amazon by following steps:
- Open “Orders” at Amazon, find the product you have purchased and open the product page;
- Click Sold by ”TokeShimi”, and click “Ask a question” on the redirected page;
- Click “An order I have placed” in the chat with Seller Messaging Assistant ;
- Click in sequence “Your product”, “Other”, “Troubleshooting” from available
options, you will see a message box after that.
Please leave us a message, and we will reply within 24 hours.
PACKING LIST
BEFORE INSTALLATION
Thank you for choosing TokeShimi products. To ensure the best experience, please read carefully and follow the instructions provided below before assembling and installing the product.
Important Safety Instructions
- Assembly by two or more adults is highly recommended, so as to ensure proper installation.
- To connect the wires to the electrical junction box, a qualified technician or electrician is highly recommended.
- Disconnect power before installing, adding, or changing any components.
- Make sure that the fixing location can support the weight of the entire fixture (e.g. solid stone or brick walls).
- To prevent injury, the mirror must be installed as per the instructions provided.
Pre-assembly
- Inspect the product immediately upon receipt for any transit damage or missing parts.
- The voltage for your product should be between 100V and 120V. If the voltage exceeds 120V, please use a transformer.
- You can connect the wires directly to your junction box or plug.
Before Installation
Please check and make sure that the mirror is functioning properly.
-
CD ON/OFF/ Brightnes s
The button controls light switch and brightness. Tap the button to turn on the light and tap again to turn it off. The brightness can be adjusted with a long press on the button. -
Anti-fog
The anti-fog function helps resist the troubling fog and keep a clear reflection image. To save energy, it will automatically turn off after one hour.
By following these steps, you can ensure that your mirror is working properly before installation. If there’re any problems, please contact us for support.
INSTALLATION
Installation Tools
-
Before installation, release the cable that connects the door and the cabinet (@). Press the lever under the hydraulic hinge (CD), detach and slide the door off the frame (@).
-
Place the medicine cabinet against the wall and mark the placement of the cabinet. Draw a line on the wall with a level and marker to indicate where the cabinet bottom is and mark spots (CD®) for the lower brackets.
NOTE: Please hang the cabinet at Least 3 inches above the faucet. -
Use an electric drill to punch holes at the marked spots (CD), then apply the wall anchors with a hammer (®).
NOTE: Please wear goggles and pay attention to your safety while drilling. -
Place the medicine cabinet securely onto the lower bracket and hold it upright. Secure two upper brackets in the groove on top of the cabinet and mark the spots on the wall.
-
Use an electric drill to punch holes at the marked spots (CD), secure the upper brackets in the groove, and mount them to the wall with screws (@).
NOTE: Gently adjust the mirror to ensure
that the mirror is securely installed. -
Connect the power. You can use the plug directly or connect the wire to a standard switch lighting circuit.
Plug-in:
Before hanging the cabinet securely, plug the power cable to a standard socket .
Hardwired :
Cut the head off the plug and hardwire it into an outlet.- BLACK WIRE — POWER SUPPLY L (HOT)
- WHITE WIRE — POWER SUPPLY N (NEUTRAL)
- GREEN WIRE — POWER SUPPLY E (EARTH)
- A WARNING: This mirror must be earthed.
- A Reminder: Please make sure the power is cut off before installation.
-
Place the cabinet in the cutout opening, secure the cabinet to the framing studs with screws, and Insert the provided shelf clips into the round holes on both sides of the cabinet. After installing the shelf clips. insert the glass shelve.
-
Attach the cabinet door back after installing the shelves (®) aplug the cable back to the top of cabinet and screw it securely (CD).
HOW TO ADJUST HYDRAULIC HINGES
Open the “DTC”cover in the direction of the arrow.
- Turn screw CD to adjust the depth of door overlay;
- Turn front screw® to adjust the gap between the door and cabinet;
- Turn the eccentric screw® to release the mounting plate from the cabinet, allowing the door to be moved up and down.
NOTE: No hydraulic hinges are applied in single-door
medicine cabinets, which adopt piano hinges instead.
SPECIFICATIONS
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>